Hi Qianyu, There are plans to enable secure boot on LS1043 soon and it would require the SPL flow. The patches for same are already available on LS1020.
Additionally we would also have drivers for CAAM for validation of next level image. Approx 48K of area needs to be reserved for this. Out of this 48K , last 32K of space in OCRAM is reserved for use by Boot ROM and 16K needs to be reserved for header of uboot. Is DEBUG being enabled by default in SPL ? What is the reason for increasing the functionality in SPL. Ideally SPL's role should be limited to DDR Init and copying of image from the boot source. Regards, Ruchika -----Original Message----- From: Q.Y. Gong Sent: Thursday, September 08, 2016 12:32 PM To: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; york sun <york....@nxp.com>; Ruchika Gupta <ruchika.gu...@nxp.com>; u-boot@lists.denx.de Cc: Vincent Hu <mingkai...@nxp.com> Subject: RE: [PATCH] armv8: ls1043a: Extend the size for SPL Hi Prabhakar, Does secure boot enable SPL on LS1043A? I only see secure boot for NOR boot. As there won't be enough space for SPL soon, I don't think it could support secure boot and SPL at the same time. Regards, Qianyu > -----Original Message----- > From: Prabhakar Kushwaha > Sent: Thursday, September 08, 2016 2:35 PM > To: Q.Y. Gong <qianyu.g...@nxp.com>; york sun <york....@nxp.com>; > Ruchika Gupta <ruchika.gu...@nxp.com>; u-boot@lists.denx.de > Cc: Vincent Hu <mingkai...@nxp.com> > Subject: RE: [PATCH] armv8: ls1043a: Extend the size for SPL > > Hi Gong, > > You have increased SPL size to 124KB. It is very high. > As per my understanding 40K has been reserved for headers to be used > during secure boot. > > Have you consider the secure boot case? > > Regards, > Prabhakar > > > -----Original Message----- > > From: Q.Y. Gong > > Sent: Thursday, September 08, 2016 8:04 AM > > To: york sun <york....@nxp.com>; u-boot@lists.denx.de > > Cc: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; Vincent Hu > > <mingkai...@nxp.com> > > Subject: RE: [PATCH] armv8: ls1043a: Extend the size for SPL > > > > Hi York, > > > > > -----Original Message----- > > > From: york sun > > > Sent: Wednesday, September 07, 2016 11:36 PM > > > To: Q.Y. Gong <qianyu.g...@nxp.com>; u-boot@lists.denx.de > > > Cc: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; Vincent Hu > > > <mingkai...@nxp.com> > > > Subject: Re: [PATCH] armv8: ls1043a: Extend the size for SPL > > > > > > On 09/07/2016 03:33 AM, Gong Qianyu wrote: > > > > The SPL images are growing much bigger especially when DEBUG is ON. > > > > So need to fix the values for them. > > > > > > > > Signed-off-by: Gong Qianyu <qianyu.g...@nxp.com> > > > > --- > > > > include/configs/ls1043a_common.h | 25 ++++++++++++++++--------- > > > > 1 file changed, 16 insertions(+), 9 deletions(-) > > > > > > > > diff --git a/include/configs/ls1043a_common.h > > > > b/include/configs/ls1043a_common.h > > > > index e55fcb2..fa20e6d 100644 > > > > --- a/include/configs/ls1043a_common.h > > > > +++ b/include/configs/ls1043a_common.h > > > > @@ -69,16 +69,22 @@ > > > > #define CONFIG_SPL_SERIAL_SUPPORT #define > > > > CONFIG_SPL_DRIVERS_MISC_SUPPORT #define > CONFIG_SPL_MMC_SUPPORT > > > > -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR > > > 0xf0 > > > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR > > > 0x110 > > > > #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500 > > > > > > > > #define CONFIG_SPL_TEXT_BASE 0x10000000 > > > > -#define CONFIG_SPL_MAX_SIZE 0x1d000 > > > > -#define CONFIG_SPL_STACK 0x1001e000 > > > > -#define CONFIG_SPL_PAD_TO 0x1d000 > > > > +/* > > > > + * CONFIG_SPL_MAX_SIZE is limited by OCRAM memory size(128 KiB) > > > > +and > > > > + * a reserved stack size(4 KiB). > > > > + * So notice that even if DEBUG is ON, the SPL > > > > +image(spl/u-boot-spl.bin) > > > > + * should not be > 124 KiB. > > > > + */ > > > > > > Qianyu, > > > > > > It is good to see comment here. However, I am concerned about your > > calculation. > > > Beside the image and stack, the early MMU tables are at the > > > beginning of > > OCRAM. > > > Did you count them? > > > > > > York > > > > No. We don't set up MMU tables in SPL stage on LS1043A/LS1046A. > > Seems so far only LS2080A has done that in SPL. > > > > > > Regards, > > Qianyu _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
