> -----Original Message----- > From: Wolfgang Denk [mailto:w...@denx.de] > Sent: Monday, August 24, 2009 5:27 PM > To: Prafulla Wadaskar > Cc: Simon Kagstrom; u-boot@lists.denx.de; Ashish Karkare; > Prabhanjan Sarnaik > Subject: Re: [U-Boot] [PATCH] ARM: compiler options cleanup - > improve tool chain support > > Dear Prafulla Wadaskar, > > In message > <73173d32e9439e4abb5151606c3e19e202e3915...@sc-vexch1.marvell. > com> you wrote: > > > > > Hm... aren't there known issues with these compiler > versions on ARM? > > I don't think so, I observed same behavior with sheevaplug, > > Which tool chain are you using? Do you see differnt behaviour with > and without USE_PRIVATE_LIBGCC=yes ? > > > i.e. "nand_bbt: Can't scan flash and build the RAM-based > BBT" message in nand init > > which was okay before this git pull > > But this is a different error message, isn;t it? > > > > Is this with or without USE_PRIVATE_LIBGCC=yes ? > > Yes, the build might be with this defined "yes", without > this build throws error message > > Argh... > > Could you please provide a usable error report? > > Which exact tool chain is this? What are your exact commands to > configure and build the board? What are the exact error messages?
Toolchain I am using toolchain bundled with fedora arm distribution i.e. armv5tel-redhat-linux-gnueabi-gcc -v Using built-in specs. Target: armv5tel-redhat-linux-gnueabi Configured with: ../configure --prefix=/usr --mandir=/usr/share/man --infodir=/usr/share/info --enable-shared --enable-threads=posix --enable-checking=release --with-system-zlib --enable-__cxa_atexit --disable-libunwind-exceptions --enable-languages=c,c++ --disable-libgcj --with-sysroot=yes --enable-version-specific-runtime-libs --target=armv5tel-redhat-linux-gnueabi Thread model: posix gcc version 4.1.2 20070925 (Red Hat 4.1.2-33.fa1) Build commands: make mrproper; make sheevaplug_config; make CROSS_COMPILE=armv5tel-redhat-linux-gnueabi- 2> warn.txt > > > This is openrd board, not yet mainlined, it is derived from > sheevaplug, (na> nd is similar) > > Alternately you can refer sheevaplug.h since problem is on > sheevaplug too. > > I don;t see any error messages when building, and I don't have such a > board to actually run the code. I get following erro only if I execute following build command make mrproper; make sheevaplug_config; make USE_PRIVATE_LIBGCC=no CROSS_COMPILE=armv5tel-redhat-linux-gnueabi- 2> warn.txt And cat warn.txt armv5tel-redhat-linux-gnueabi-ld: cannot find -lgcc make: *** [u-boot] Error 1 Whereas, if I unset first USE_PRIVATE_LIBGCC then I do not get this error and build is through My invocation may be wrong but shouldn't it treat USE_PRIVATE_LIBGCC=no as unset? > > > I tried removing this patch and things are normal on sheevaplug > > I wish you had reported such issues when the patch was posted. There > has been _long_ discussion about it. I am really sory about this, I was away from h/w hence could not check in time :-( Regards.. Prafulla . . > > Best regards, > > Wolfgang Denk > > -- > DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de > "This is a test of the Emergency Broadcast System. If this had been an > actual emergency, do you really think we'd stick around to tell you?" > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
