[U-Boot] [PATCH v2 3/5] cgtqmx6eval: Add SPI NOR flash support

[Otavio Salvador]

Add SPI NOR support:

=> sf probe
SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB

Signed-off-by: Otavio Salvador <ota...@ossystems.com.br>
---
Changes since v1:
- None

 board/congatec/cgtqmx6eval/cgtqmx6eval.c | 23 +++++++++++++++++++++++
 include/configs/cgtqmx6eval.h            | 10 ++++++++++
 2 files changed, 33 insertions(+)

diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c 
b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
index 574891e..a9694d5 100644
--- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c
+++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
@@ -45,6 +45,10 @@ DECLARE_GLOBAL_DATA_PTR;
        PAD_CTL_DSE_40ohm | PAD_CTL_HYS |                       \
        PAD_CTL_ODE | PAD_CTL_SRE_FAST)
 
+#define SPI_PAD_CTRL (PAD_CTL_HYS |                            \
+       PAD_CTL_SPEED_MED |             \
+       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
 #define MX6Q_QMX6_PFUZE_MUX            IMX_GPIO_NR(6, 9)
 
 
@@ -152,6 +156,13 @@ static iomux_v3_cfg_t enet_pads_ar8035[] = {
        MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+       MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+       MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+       MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+       MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 struct i2c_pads_info i2c_pad_info1 = {
        .scl = {
@@ -382,6 +393,12 @@ static void setup_iomux_uart(void)
        imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
 }
 
+void setup_spinor(void)
+{
+       imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+       gpio_direction_output(IMX_GPIO_NR(3, 19), 0);
+}
+
 #ifdef CONFIG_FSL_ESDHC
 static struct fsl_esdhc_cfg usdhc_cfg[] = {
        {USDHC2_BASE_ADDR},
@@ -647,6 +664,7 @@ int board_early_init_f(void)
 {
        setup_iomux_uart();
        setup_display();
+       setup_spinor();
 
        return 0;
 }
@@ -672,6 +690,11 @@ int checkboard(void)
        return 0;
 }
 
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+       return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -EINVAL;
+}
+
 #ifdef CONFIG_CMD_BMODE
 static const struct boot_mode board_boot_modes[] = {
        /* 4 bit bus width */
diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h
index 92930c8..d0d098a 100644
--- a/include/configs/cgtqmx6eval.h
+++ b/include/configs/cgtqmx6eval.h
@@ -29,6 +29,16 @@
 /* MMC Configs */
 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
 
+/* SPI NOR */
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS          0
+#define CONFIG_SF_DEFAULT_SPEED                20000000
+#define CONFIG_SF_DEFAULT_MODE         (SPI_MODE_0)
+
 /* Miscellaneous commands */
 #define CONFIG_CMD_BMODE
 
-- 
1.9.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot