[U-Boot] Using spi_alloc_slave() from SPL

[Fabio Estevam]

Hi,

I am trying to use spi_flash_probe() inside SPL on a custom mx6 board.

The idea is to read some parameters from the SPI NOR flash and configure
the DDR accordingly.

This is similar to what gw_ventana_spl.c does, but it reads from i2c
eeprom instead of SPI NOR.

Here are the changes just to illustrate the problem:

--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -692,6 +692,19 @@ int checkboard(void)
 #ifdef CONFIG_SPL_BUILD
 #include <spl.h>
 #include <libfdt.h>
+#include <spi_flash.h>
+#include <spi.h>
+
+static int read_spi_flash(void)
+{
+       struct spi_flash *spi;
+       char buf[2];
+
+       spi = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
+                             CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+       return spi_flash_read(spi, 0, 2, buf);
+}

 const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
        .dram_sdclk_0 =  0x00020030,
@@ -837,6 +850,8 @@ void board_init_f(ulong dummy)
        /* UART clocks enabled and gd valid - init serial console */
        preloader_console_init();

+       read_spi_flash();
+
        /* DDR initialization */
        spl_dram_init();

diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index 41162ca..f5dfaf7 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -12,6 +12,10 @@
 #ifdef CONFIG_SPL
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SYS_SPI_U_BOOT_OFFS     (64 * 1024)
+#define CONFIG_SPL_SPI_LOAD
 #include "imx6_spl.h"
 #endif

@@ -35,6 +39,12 @@
 #define CONFIG_SYS_MMC_ENV_DEV         1       /* SDHC3 */
 #endif

+#define CONFIG_ENV_SECT_SIZE           (64 * 1024)
+#define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
+
 #define CONFIG_CMD_PCI
 #ifdef CONFIG_CMD_PCI
 #define CONFIG_PCI
-- 
1.9.1

The when I run it:

U-Boot SPL 2015.07-08202-g6dcdca1-dirty (Aug 06 2015 - 10:18:33)
mxc_spi: SPI Slave not allocated !

spi_flash_probe() ---> spi_setup_slave() ----> spi_alloc_slave() which
fails on mxc_spi.c

As read_spi_flash() is called prior to the DDR initialization,
spi_alloc_slave() fails.

Is there a way to avoid calling spi_alloc_slave() in the SPL case?

Any ideas on how to fix this?

Thanks,

Fabio Estevam
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot