Yes, then you need to set/use CONFIG_BOOTDELAY to enable or disable for autoboot. For details and information have a look at doc/README.autoboot
Once you use CONFIG_BOOTDELAY, then recompile and generate u-boot.bin, if everything goes fine you would have bootdelay option in you printenv settings. Kind Regards, Vijay Nikam On Sat, May 23, 2009 at 9:49 AM, paras <bepa...@gmail.com> wrote: > Thank you Sir for your response. > As per your instruction I set "bootdelay" variable. log is given below, But > the problem is not solve. I run command "run bootcmd" for booting the > kernel. > > ------------------------------------------ LOG > ------------------------------------------------------------- > ramboot=setenv rootdev /dev/ram;run setbootargs;tftp $ramdiskaddr > $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr > $ramdiskaddr $fdtaddr > nfsboot=setenv rootdev /dev/nfs;run setbootargs;run setipargs;tftp $loadaddr > $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr > baudrate=115200 > loads_echo=1 > ethaddr=00:E0:0C:00:95:01 > eth1addr=00:E0:0C:00:95:02 > rootpath=/nfs/root/path > hostname=mpc8313erdb > bootfile=uImage > loadaddr=200000 > netdev=eth1 > ethprime=TSEC1 > uboot=u-boot.bin > tftpflash=tftpboot $loadaddr $uboot; protect off 0xFE000000 +$filesize; > erase 0xFE000000 +$filesize; cp.b $loadaddr 0xFE000000 $filesize; protect on > 0xFE000000 +$filesize; cmp.b $e > fdtaddr=400000 > fdtfile=mpc8313erdb.dtb > console=ttyS0 > setbootargs=setenv bootargs root=$rootdev rw console=$console,$baudrate > $othbootargs > setipargs=setenv bootargs nfsroot=$serverip:$rootpath > ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off root=$rootdev > rw console=$console,$baudrate $othbootargs > filesize=490000 > fileaddr=100000 > netmask=255.0.0.0 > bootargs=root=/dev/mtdblock6 rootfstype=jffs2 rw console=ttyS0,115200 > bootcmd=cp.b fe710000 40000 11000; go 40004; bootm fe100000 - fe700000 > *bootdelay=3* > stdin=serial > stdout=serial > stderr=serial > ethact=TSEC1 > -------------------------------------------------------------------------------------------------------------------------------------------------- > > Thanks In Advance. > > > On Fri, May 22, 2009 at 4:22 PM, Wolfgang Denk <w...@denx.de> wrote: > >> Dear paras, >> >> In message <8136f0210905220236o93ab0a0gbf8ff5e15192e...@mail.gmail.com> >> you wrote: >> > >> > I am working on MPC8313erdb board. I configure U-Boot 1.3.0 for my board, >> >> U-Boot 1.3.0 is very old. Why don't you use current code? >> >> > But the problem is on auto-boot. >> > When I start the board it stop on command prompt of u-boot. >> >> That's normal given your setup. Try setting "bootdelay". >> >> Best regards, >> >> Wolfgang Denk >> >> -- >> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel >> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany >> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de >> "Do we define evil as the absence of goodness? It seems only logical >> that shit happens--we discover this by the process of elimination." >> -- Larry Wall >> > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
