Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to
DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabha...@freescale.com>
---
This patch depends upon
"[PATCH 3] powerpc/t104xrdb: Unification of T104xRDB header files"
http://patchwork.ozlabs.org/patch/335207/
board/freescale/t104xrdb/Makefile | 7 +-
board/freescale/t104xrdb/README | 87 ++++++++++++++++++++++
board/freescale/t104xrdb/ddr.c | 5 +-
board/freescale/t104xrdb/spl.c | 118 +++++++++++++++++++++++++++++
board/freescale/t104xrdb/t1040_rcw.cfg | 7 ++
board/freescale/t104xrdb/t1042_rcw.cfg | 7 ++
board/freescale/t104xrdb/t104x_pbi.cfg | 26 +++++++
board/freescale/t104xrdb/tlb.c | 12 +++
boards.cfg | 6 ++
include/configs/T104xRDB.h | 128 ++++++++++++++++++++++++++++----
10 files changed, 384 insertions(+), 19 deletions(-)
create mode 100644 board/freescale/t104xrdb/spl.c
create mode 100644 board/freescale/t104xrdb/t1040_rcw.cfg
create mode 100644 board/freescale/t104xrdb/t1042_rcw.cfg
create mode 100644 board/freescale/t104xrdb/t104x_pbi.cfg
diff --git a/board/freescale/t104xrdb/Makefile
b/board/freescale/t104xrdb/Makefile
index e51fb7a..a68c951 100644
--- a/board/freescale/t104xrdb/Makefile
+++ b/board/freescale/t104xrdb/Makefile
@@ -4,10 +4,13 @@
# SPDX-License-Identifier: GPL-2.0+
#
-
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
obj-y += t104xrdb.o
-obj-y += ddr.o
obj-y += eth.o
obj-$(CONFIG_PCI) += pci.o
+endif
+obj-y += ddr.o
obj-y += law.o
obj-y += tlb.o
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index 1da52bb..4001ac8 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -198,3 +198,90 @@ The below commands apply to the board
2.To change from vbank4 to vbank0
=> qixis reset (it will boot using vbank0)
+
+NAND boot with 2 Stage boot loader
+----------------------------------
+PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(768 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+ Run time view of SPL framework during NAND boot :-
+ -----------------------------------------------
+ Area | Address |
+-----------------------------------------------
+ Reserve | 0xFFFC0000 (32KB) |
+ -----------------------------------------------
+ GD, BD | 0xFFFC8000 (4KB) |
+ -----------------------------------------------
+ ENV | 0xFFFC9000 (6KB) |
+ -----------------------------------------------
+ HEAP | 0xFFFCA800 (34KB) |
+ -----------------------------------------------
+ STACK | 0xFFFD8000 (20KB) |
+ -----------------------------------------------
+ U-boot SPL | 0xFFFD8000 (160KB) |
+ -----------------------------------------------
+
+ Run time view of SPL framework during SD, SPI boot :-
+ -----------------------------------------------
+ Area | Address |
+-----------------------------------------------
+ Reserve | 0xFFFC0000 (32KB) |
+ -----------------------------------------------
+ GD, BD | 0xFFFC8000 (4KB) |
+ -----------------------------------------------
+ HEAP | 0xFFFC9000 (40KB) |
+ -----------------------------------------------
+ STACK | 0xFFFD8000 (20KB) |
+ -----------------------------------------------
+ U-boot SPL | 0xFFFD8000 (160KB) |
+ -----------------------------------------------
+
+NAND Flash memory Map on T104xRDB
+------------------------------------------
+ Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB
+0x180000 0x19FFFF u-boot env 128KB
+0x200000 0x21FFFF FMAN Ucode 128KB
+0x280000 0x29FFFF QE Firmware 128KB
+
+SD Card memory Map on T104xRDB
+------------------------------------------
+ Block #blocks Definition Size
+0x008 2048 u-boot 1MB
+0x800 0024 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+SPI Flash memory Map on T104xRDB
+------------------------------------------
+ Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+Please note QE Firmware is only valid for T1040RDB
+
+
+Switch Settings: (ON is 0, OFF is 1)
+===============
+NAND boot SW setting:
+SW1: 10001000
+SW2: 00111001
+SW3: 11110001
+
+SPI boot SW setting:
+SW1: 00100010
+SW2: 10111001
+SW3: 11100001
+
+SD boot SW setting:
+SW1: 00100000
+SW2: 00111001
+SW3: 11100001
diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c
index 57d0f9c..34c9224 100644
--- a/board/freescale/t104xrdb/ddr.c
+++ b/board/freescale/t104xrdb/ddr.c
@@ -113,6 +113,7 @@ phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
puts("Initializing....using SPD\n");
dram_size = fsl_ddr_sdram();
@@ -120,6 +121,8 @@ phys_size_t initdram(int board_type)
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
- puts(" DDR: ");
+#else
+ dram_size = fsl_ddr_sdram_size();
+#endif
return dram_size;
}
diff --git a/board/freescale/t104xrdb/spl.c b/board/freescale/t104xrdb/spl.c
new file mode 100644
index 0000000..3aca0ca
--- /dev/null
+++ b/board/freescale/t104xrdb/spl.c
@@ -0,0 +1,118 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, uart_clk;
+#ifdef CONFIG_SPL_NAND_BOOT
+ u32 porsr1, pinctl;
+#endif
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ /*
+ * There is T1040 SoC issue where NOR, FPGA are inaccessible during
+ * NAND boot because IFC signals > IFC_AD7 are not enabled.
+ * This workaround changes RCW source to make all signals enabled.
+ */
+ porsr1 = in_be32(&gur->porsr1);
+ pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+ out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+ __asm__ __volatile__("" : : : "memory");
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ uart_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ uart_clk / 16 / CONFIG_BAUDRATE);
+
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifndef CONFIG_SPL_NAND_BOOT
+ env_init();
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+
+ /* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+#else
+ env_relocate();
+#endif
+
+ i2c_init_all();
+
+ puts("\n\n");
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t104xrdb/t1040_rcw.cfg
b/board/freescale/t104xrdb/t1040_rcw.cfg
new file mode 100644
index 0000000..3300c18
--- /dev/null
+++ b/board/freescale/t104xrdb/t1040_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0c18000e 0e000000 00000000 00000000
+66000002 80000002 e8106000 01000000
+00000000 00000000 00000000 00032810
+00000000 0342500f 00000000 00000000
diff --git a/board/freescale/t104xrdb/t1042_rcw.cfg
b/board/freescale/t104xrdb/t1042_rcw.cfg
new file mode 100644
index 0000000..a3ea8ad
--- /dev/null
+++ b/board/freescale/t104xrdb/t1042_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0c18000e 0e000000 00000000 00000000
+06000002 00400002 e8106000 01000000
+00000000 00000000 00000000 00030810
+00000000 01fe0a06 00000000 00000000
diff --git a/board/freescale/t104xrdb/t104x_pbi.cfg
b/board/freescale/t104xrdb/t104x_pbi.cfg
new file mode 100644
index 0000000..7b9e9b0
--- /dev/null
+++ b/board/freescale/t104xrdb/t104x_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c
index 84f97a4..95c15aa 100644
--- a/board/freescale/t104xrdb/tlb.c
+++ b/board/freescale/t104xrdb/tlb.c
@@ -53,6 +53,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
+#ifndef CONFIG_SPL_BUILD
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -82,6 +83,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 8, BOOKE_PAGESZ_16M, 1),
#endif
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -102,6 +104,16 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 11, BOOKE_PAGESZ_256K, 1),
#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 12, BOOKE_PAGESZ_1G, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 76f3aae..1c96a51 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -933,7 +933,13 @@ Active powerpc mpc85xx - freescale
p2041rdb
Active powerpc mpc85xx - freescale p2041rdb
P2041RDB_SRIO_PCIE_BOOT
P2041RDB:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
-
Active powerpc mpc85xx - freescale t1040qds
T1040QDS T1040QDS:PPC_T1040
Poonam Aggrwal <poonam.aggr...@freescale.com>
Active powerpc mpc85xx - freescale t104xrdb
T1040RDB T104xRDB:PPC_T1040,T1040RDB
Priyanka Jain <priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1040RDB_NAND
T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,RAMBOOT_SPLPBL,NAND
Priyanka Jain
<priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1040RDB_SPIFLASH
T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,RAMBOOT_SPLPBL,SPIFLASH
Priyanka Jain
<priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1040RDB_SDCARD
T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,RAMBOOT_SPLPBL,SDCARD
Active powerpc mpc85xx - freescale t104xrdb
T1042RDB_PI T104xRDB:PPC_T1042,T1042RDB_PI
Priyanka Jain <priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1042RDB_PI_NAND
T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,RAMBOOT_SPLPBL,NAND
Priyanka Jain
<priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1042RDB_PI_SPIFLASH
T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,RAMBOOT_SPLPBL,SPIFLASH
Priyanka Jain
<priyanka.j...@freescale.com>
+Active powerpc mpc85xx - freescale t104xrdb
T1042RDB_PI_SDCARD
T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,RAMBOOT_SPLPBL,SDCARD
Active powerpc mpc85xx - freescale t208xqds
T2080QDS T208xQDS:PPC_T2080
-
Active powerpc mpc85xx - freescale t208xqds
T2080QDS_NAND
T208xQDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
-
Active powerpc mpc85xx - freescale t208xqds
T2080QDS_SDCARD
T208xQDS:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000
-
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 90ac1ec..6e0bb2b 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -14,8 +14,79 @@
#define CONFIG_PHYS_64BIT
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI
$(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg
+#ifdef CONFIG_T1040RDB
+#define CONFIG_SYS_FSL_PBL_RCW
$(SRCTREE)/board/freescale/t104xrdb/t1040_rcw.cfg
+#endif
+#ifdef CONFIG_T1042RDB_PI
+#define CONFIG_SYS_FSL_PBL_RCW
$(SRCTREE)/board/freescale/t104xrdb/t1042_rcw.cfg
+#endif
+
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
+#define CONFIG_SPL_PAD_TO 0x40000
+#define CONFIG_SPL_MAX_SIZE 0x28000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+#define RESET_VECTOR_OFFSET 0x27FFC
+#define BOOT_PAGE_OFFSET 0x27000
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
#endif
/* High Level Configuration Options */
@@ -50,15 +121,12 @@
#define CONFIG_ENV_OVERWRITE
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
+#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif
-#ifndef CONFIG_SYS_NO_FLASH
#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
@@ -70,11 +138,11 @@
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1658)
+#define CONFIG_ENV_OFFSET (512 * 0x800)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_ENV_IS_IN_FLASH
@@ -82,10 +150,6 @@
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 66666666
@@ -117,6 +181,18 @@
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_L3_SIZE 256 << 10
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_NAND
+#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 10 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (34 << 10)
+#else
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (40 << 10)
+#endif
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (20 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
@@ -279,7 +355,11 @@
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of
monitor */
+#endif
#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
@@ -327,7 +407,9 @@
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+#endif
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
@@ -517,11 +599,11 @@
#elif defined(CONFIG_SDCARD)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image
is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size
is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 0x820)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_QE_FMAN_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
@@ -529,6 +611,20 @@
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000
#endif
+
+#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_QE_FW_ADDR 0x130000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FW_ADDR (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FW_ADDR 0xEFF10000
+#endif
+#endif
+
+
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */
--
1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
