BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW |GPMC |ELM H/W engine |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC |S/W BCH library |
+-----------------------------------+-----------------+-----------------+
Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.
This patch
- removes CONFIG_AM33xx
Thus this driver can be reused by all devices having ELM h/w engine.
- removes CONFIG_NAND_OMAP_BCH8 and adds new CONFIG_NAND_OMAP_ECCSCHEME
CONFIG_NAND_OMAP_ECCSCHEME determines ecc-scheme to be used
refer doc/README.nand and board/ti/am335x/README
- adds omap_select_ecc_scheme()
A common function to handle ecc-scheme related configurations. This
can be used both during device-probe and via user-space u-boot commads
to change ecc-scheme. During device probe ecc-scheme is selected based
on CONFIG_NAND_OMAP_ECCSCHEME.
- enables CONFIG_BCH
S/W library (lib/bch.c) required by OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
for auto-detection of ONFI compliant NAND devices
- updates following README doc
doc/README.nand
board/ti/am335x/README
doc/README.omap3
Signed-off-by: Pekon Gupta <pe...@ti.com>
---
arch/arm/include/asm/arch-am33xx/omap_gpmc.h | 52 ++---
doc/README.nand | 30 +++
doc/README.omap3 | 4 +-
drivers/mtd/nand/omap_gpmc.c | 287 +++++++++++++++------------
include/configs/am335x_evm.h | 11 +-
include/configs/tricorder.h | 3 +-
6 files changed, 216 insertions(+), 171 deletions(-)
diff --git a/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
b/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
index 00ad1d0..62f608e 100644
--- a/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
+++ b/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
@@ -7,42 +7,20 @@
#ifndef __ASM_ARCH_OMAP_GPMC_H
#define __ASM_ARCH_OMAP_GPMC_H
-/* These GPMC_NAND_HW_BCHx_ECC_LAYOUT defines are based on AM33xx ELM */
-#define GPMC_NAND_HW_BCH4_ECC_LAYOUT {\
- .eccbytes = 32,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33},\
- .oobfree = {\
- {.offset = 34,\
- .length = 30 } } \
-}
+enum omap_ecc {
+ /* 1-bit ECC calculation by Software, Error detection by Software */
+ OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */
+ /* 1-bit ECC calculation by GPMC, Error detection by Software */
+ /* ECC layout compatible to legacy ROMCODE. */
+ OMAP_ECC_HAM1_CODE_HW,
+ /* 4-bit ECC calculation by GPMC, Error detection by Software */
+ OMAP_ECC_BCH4_CODE_HW_DETECTION_SW,
+ /* 4-bit ECC calculation by GPMC, Error detection by ELM */
+ OMAP_ECC_BCH4_CODE_HW,
+ /* 8-bit ECC calculation by GPMC, Error detection by Software */
+ OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
+ /* 8-bit ECC calculation by GPMC, Error detection by ELM */
+ OMAP_ECC_BCH8_CODE_HW,
+};
-#define GPMC_NAND_HW_BCH8_ECC_LAYOUT {\
- .eccbytes = 56,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
- 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
- 52, 53, 54, 55, 56, 57},\
- .oobfree = {\
- {.offset = 58,\
- .length = 6 } } \
-}
-
-#define GPMC_NAND_HW_BCH16_ECC_LAYOUT {\
- .eccbytes = 104,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
- 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
- 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,\
- 64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75,\
- 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,\
- 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99,\
- 100, 101, 102, 103, 104, 105},\
- .oobfree = {\
- {.offset = 106,\
- .length = 8 } } \
-}
#endif /* __ASM_ARCH_OMAP_GPMC_H */
diff --git a/doc/README.nand b/doc/README.nand
index 913e9b5..f9c921e 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -169,6 +169,36 @@ Configuration Options:
Please convert your driver even if you don't need the extra
flexibility, so that one day we can eliminate the old mechanism.
+ CONFIG_SYS_NAND_ONFI_DETECTION
+ Enables detection of ONFI compliant devices during probe.
+ And fetching device parameters flashed on device, by parsing
+ ONFI parameter page.
+
+ CONFIG_BCH
+ Enables software based BCH ECC algorithm present in lib/bch.c
+ This is used by SoC platforms which do not have built-in ELM
+ hardware engine required for BCH ECC correction.
+
+Platform specific options
+=========================
+
+ CONFIG_NAND_OMAP_ECCSCHEME
+ On OMAP platforms, this specifies NAND ECC scheme.
+ 1 - HAM1_SW 1-bit Hamming code using software library
+ (for legacy devices only)
+ 2 - HAM1_HW 1-bit Hamming code using GPMC hardware engine
+ (for legacy devices only)
+ 3 - BCH4_SW 4-bit BCH code (unsupported)
+ 4 - BCH4_HW 4-bit BCH code (unsupported)
+ 5 - BCH8_SW 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using software library.
+ - requires CONFIG_BCH to enable software BCH library
+ (For legacy device which do not have ELM h/w engine)
+ 6 - BCH8_HW 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using ELM hardware engine.
+
NOTE:
=====
diff --git a/doc/README.omap3 b/doc/README.omap3
index 1fbe79d..fd85b22 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -161,8 +161,8 @@ BCH8
To enable hardware assisted BCH8 (8-bit BCH [Bose, Chaudhuri, Hocquenghem]) on
OMAP3 devices we can use the BCH library in lib/bch.c. To do so add CONFIG_BCH
-to enable the library and CONFIG_NAND_OMAP_BCH8 to to enable hardware assisted
-syndrom generation to your board config.
+to enable the library and set CONFIG_NAND_OMAP_ECCSCHEME=5 (as per README.nand)
+to enable BCH8_SW ecc scheme.
The NAND OOB layout is the same as in linux kernel, if the linux kernel BCH8
implementation for OMAP3 works for you so the u-boot version should also.
When you require the SPL to read with BCH8 there are two more configs to
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index ec1787f..7396bee 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -15,15 +15,13 @@
#include <linux/bch.h>
#include <linux/compiler.h>
#include <nand.h>
-#ifdef CONFIG_AM33XX
#include <asm/arch/elm.h>
-#endif
+
+#define BADBLOCK_MARKER_LENGTH 2
+#define SECTOR_BYTES 512
static uint8_t cs;
-static __maybe_unused struct nand_ecclayout hw_nand_oob =
- GPMC_NAND_HW_ECC_LAYOUT;
-static __maybe_unused struct nand_ecclayout hw_bch8_nand_oob =
- GPMC_NAND_HW_BCH8_ECC_LAYOUT;
+static __maybe_unused struct nand_ecclayout omap_ecclayout;
/*
* omap_nand_hwcontrol - Set the address pointers corretly for the
@@ -233,6 +231,7 @@ struct nand_bch_priv {
uint8_t type;
uint8_t nibbles;
struct bch_control *control;
+ enum omap_ecc ecc_scheme;
};
/* bch types */
@@ -274,17 +273,15 @@ static void omap_hwecc_init_bch(struct nand_chip *chip,
int32_t mode)
{
uint32_t val;
uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
-#ifdef CONFIG_AM33XX
uint32_t unused_length = 0;
-#endif
uint32_t wr_mode = BCH_WRAPMODE_6;
struct nand_bch_priv *bch = chip->priv;
/* Clear the ecc result registers, select ecc reg as 1 */
writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
-#ifdef CONFIG_AM33XX
- wr_mode = BCH_WRAPMODE_1;
+ if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) {
+ wr_mode = BCH_WRAPMODE_1;
switch (bch->nibbles) {
case ECC_BCH4_NIBBLES:
@@ -320,7 +317,7 @@ static void omap_hwecc_init_bch(struct nand_chip *chip,
int32_t mode)
val |= (unused_length << 22);
break;
}
-#else
+ } else {
/*
* This ecc_size_config setting is for BCH sw library.
*
@@ -333,7 +330,7 @@ static void omap_hwecc_init_bch(struct nand_chip *chip,
int32_t mode)
* size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
*/
val = (32 << 22) | (0 << 12);
-#endif
+ }
/* ecc size configuration */
writel(val, &gpmc_cfg->ecc_size_config);
@@ -376,9 +373,8 @@ static void __maybe_unused omap_ecc_disable(struct mtd_info
*mtd)
}
/*
- * BCH8 support (needs ELM and thus AM33xx-only)
+ * BCH support using ELM module
*/
-#ifdef CONFIG_AM33XX
/*
* omap_read_bch8_result - Read BCH result for BCH8 level
*
@@ -631,20 +627,19 @@ static int omap_read_page_bch(struct mtd_info *mtd,
struct nand_chip *chip,
}
return 0;
}
-#endif /* CONFIG_AM33XX */
/*
* OMAP3 BCH8 support (with BCH library)
*/
-#ifdef CONFIG_NAND_OMAP_BCH8
+#ifdef CONFIG_BCH
/*
- * omap_calculate_ecc_bch - Read BCH ECC result
+ * omap_calculate_ecc_bch_sw - Read BCH ECC result
*
* @mtd: MTD device structure
* @dat: The pointer to data on which ecc is computed (unused here)
* @ecc: The ECC output buffer
*/
-static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat,
+static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat,
uint8_t *ecc)
{
int ret = 0;
@@ -689,13 +684,13 @@ static int omap_calculate_ecc_bch(struct mtd_info *mtd,
const uint8_t *dat,
}
/**
- * omap_correct_data_bch - Decode received data and correct errors
+ * omap_correct_data_bch_sw - Decode received data and correct errors
* @mtd: MTD device structure
* @data: page data
* @read_ecc: ecc read from nand flash
* @calc_ecc: ecc read from HW ECC registers
*/
-static int omap_correct_data_bch(struct mtd_info *mtd, u_char *data,
+static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data,
u_char *read_ecc, u_char *calc_ecc)
{
int i, count;
@@ -752,7 +747,115 @@ static void __maybe_unused omap_free_bch(struct mtd_info
*mtd)
chip_priv->control = NULL;
}
}
-#endif /* CONFIG_NAND_OMAP_BCH8 */
+#endif /* CONFIG_BCH */
+
+/**
+ * omap_select_ecc_scheme - configures driver for particular ecc-scheme
+ * @nand: NAND chip device structure
+ * @ecc_scheme: ecc scheme to configure
+ * @pagesize: number of main-area bytes per page of NAND device
+ * @oobsize: number of OOB/spare bytes per page of NAND device
+ */
+static int omap_select_ecc_scheme(struct nand_chip *nand, int ecc_scheme,
+ unsigned int pagesize, unsigned int oobsize) {
+ struct nand_bch_priv *bch = nand->priv;
+ struct nand_ecclayout *ecclayout = nand->ecc.layout;
+ int i;
+
+ switch (ecc_scheme) {
+ case OMAP_ECC_HAM1_CODE_SW:
+ debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n");
+ nand->ecc.mode = NAND_ECC_SOFT;
+ nand->ecc.layout = NULL;
+ nand->ecc.size = 0;
+ nand->ecc.strength = 1;
+ bch->ecc_scheme = OMAP_ECC_HAM1_CODE_SW;
+ break;
+ case OMAP_ECC_HAM1_CODE_HW:
+ debug("nand: selected OMAP_ECC_HAM1_CODE_HW\n");
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 1;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 3;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data;
+ nand->ecc.calculate = omap_calculate_ecc;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes *
+ (pagesize / SECTOR_BYTES);
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ bch->ecc_scheme = OMAP_ECC_HAM1_CODE_HW;
+ break;
+#ifdef CONFIG_BCH
+ case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+ debug("nand: selected OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n");
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 8;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 13;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch_sw;
+ nand->ecc.calculate = omap_calculate_ecc_bch_sw;
+ /* BCH SW library is used for error detection */
+ bch_priv.control = init_bch(13, 8, 0x201b);
+ if (!bch_priv.control) {
+ printf("nand: error: could not init_bch()\n");
+ return -ENODEV;
+ }
+ bch_priv.type = ECC_BCH8;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes *
+ (pagesize / SECTOR_BYTES);
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + (oobsize -
+ ecclayout->eccbytes);
+ ecclayout->oobfree[0].offset = BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+ bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
+ break;
+#endif
+ case OMAP_ECC_BCH8_CODE_HW:
+ debug("nand: selected OMAP_ECC_BCH8_CODE_HW\n");
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 8;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 14;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ nand->ecc.read_page = omap_read_page_bch;
+ /* ELM is used for ECC error detection */
+ elm_init();
+ bch_priv.type = ECC_BCH8;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes *
+ (pagesize / SECTOR_BYTES);
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW;
+ break;
+ default:
+ debug("nand: error: ecc scheme not enabled or supported\n");
+ return -EINVAL;
+ }
+
+ /* check if NAND spare/OOB has enough bytes to accomodate ecclayout */
+ if ((ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH) > oobsize) {
+ printf("nand: error: insufficient OOB bytes. require=%d\n", (
+ ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH));
+ return -EINVAL;
+ }
+ return 0;
+}
#ifndef CONFIG_SPL_BUILD
/*
@@ -763,77 +866,52 @@ static void __maybe_unused omap_free_bch(struct mtd_info
*mtd)
* @eccstrength - the number of bits that could be corrected
* (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16)
*/
-void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
+int omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
{
struct nand_chip *nand;
struct mtd_info *mtd;
+ struct nand_bch_priv *bch;
+ int err = 0;
if (nand_curr_device < 0 ||
nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE ||
!nand_info[nand_curr_device].name) {
- printf("Error: Can't switch ecc, no devices available\n");
- return;
+ printf("nand: error: no NAND devices found\n");
+ return -ENODEV;
}
mtd = &nand_info[nand_curr_device];
nand = mtd->priv;
-
+ bch = nand->priv;
nand->options |= NAND_OWN_BUFFERS;
-
- /* Reset ecc interface */
- nand->ecc.mode = NAND_ECC_NONE;
- nand->ecc.read_page = NULL;
- nand->ecc.write_page = NULL;
- nand->ecc.read_oob = NULL;
- nand->ecc.write_oob = NULL;
- nand->ecc.hwctl = NULL;
- nand->ecc.correct = NULL;
- nand->ecc.calculate = NULL;
- nand->ecc.strength = eccstrength;
-
/* Setup the ecc configurations again */
if (hardware) {
if (eccstrength == 1) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_nand_oob;
- nand->ecc.size = 512;
- nand->ecc.bytes = 3;
- nand->ecc.hwctl = omap_enable_hwecc;
- nand->ecc.correct = omap_correct_data;
- nand->ecc.calculate = omap_calculate_ecc;
- omap_hwecc_init(nand);
- printf("1-bit hamming HW ECC selected\n");
- }
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
- else if (eccstrength == 8) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_bch8_nand_oob;
- nand->ecc.size = 512;
-#ifdef CONFIG_AM33XX
- nand->ecc.bytes = 14;
- nand->ecc.read_page = omap_read_page_bch;
-#else
- nand->ecc.bytes = 13;
-#endif
- nand->ecc.hwctl = omap_enable_ecc_bch;
- nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
- printf("8-bit BCH HW ECC selected\n");
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_HAM1_CODE_HW,
+ mtd->writesize, mtd->oobsize);
+ } else if (eccstrength == 8) {
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_BCH8_CODE_HW,
+ mtd->writesize, mtd->oobsize);
+ } else {
+ printf("nand: error: unsupported ECC scheme\n");
+ return -EINVAL;
}
-#endif
} else {
- nand->ecc.mode = NAND_ECC_SOFT;
- /* Use mtd default settings */
- nand->ecc.layout = NULL;
- nand->ecc.size = 0;
- printf("SW ECC selected\n");
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
+ mtd->writesize, mtd->oobsize);
+ }
+ if (err) {
+ printf("nand: error: could not switch ecc, reverting\n");
+ omap_select_ecc_scheme(nand, bch->ecc_scheme,
+ mtd->writesize, mtd->oobsize);
+ return -EINVAL;
}
/* Update NAND handling after ECC mode switch */
- nand_scan_tail(mtd);
-
- nand->options &= ~NAND_OWN_BUFFERS;
+ err = nand_scan_tail(mtd);
+ return err;
}
#endif /* CONFIG_SPL_BUILD */
@@ -873,7 +951,7 @@ int board_nand_init(struct nand_chip *nand)
cs++;
}
if (cs >= GPMC_MAX_CS) {
- printf("NAND: Unable to find NAND settings in "
+ printf("nand: error: Unable to find NAND settings in "
"GPMC Configuration - quitting\n");
return -ENODEV;
}
@@ -885,64 +963,23 @@ int board_nand_init(struct nand_chip *nand)
nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
-
- nand->cmd_ctrl = omap_nand_hwcontrol;
- nand->options = NAND_NO_PADDING | NAND_CACHEPRG;
+ nand->priv = &bch_priv;
+ nand->cmd_ctrl = omap_nand_hwcontrol;
+ nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
/* If we are 16 bit dev, our gpmc config tells us that */
if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
nand->options |= NAND_BUSWIDTH_16;
nand->chip_delay = 100;
-
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
-#ifdef CONFIG_AM33XX
- /* AM33xx uses the ELM */
- /* required in case of BCH */
- elm_init();
-#else
- /*
- * Whereas other OMAP based SoC do not have the ELM, they use the BCH
- * SW library.
- */
- bch_priv.control = init_bch(13, 8, 0x201b /* hw polynominal */);
- if (!bch_priv.control) {
- puts("Could not init_bch()\n");
- return -ENODEV;
+ nand->ecc.layout = &omap_ecclayout;
+
+ /* select ECC scheme */
+ if (omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
+ CONFIG_SYS_NAND_PAGE_SIZE,
+ CONFIG_SYS_NAND_OOBSIZE)) {
+ printf("nand: error: unsupported ecc scheme specified\n");
+ return -EINVAL;
}
-#endif
- /* BCH info that will be correct for SPL or overridden otherwise. */
- nand->priv = &bch_priv;
-#endif
-
- /* Default ECC mode */
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_bch8_nand_oob;
- nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
- nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
- nand->ecc.strength = 8;
- nand->ecc.hwctl = omap_enable_ecc_bch;
- nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
-#ifdef CONFIG_AM33XX
- nand->ecc.read_page = omap_read_page_bch;
-#endif
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
-#else
-#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
- nand->ecc.mode = NAND_ECC_SOFT;
-#else
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_nand_oob;
- nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
- nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
- nand->ecc.hwctl = omap_enable_hwecc;
- nand->ecc.correct = omap_correct_data;
- nand->ecc.calculate = omap_calculate_ecc;
- nand->ecc.strength = 1;
- omap_hwecc_init(nand);
-#endif
-#endif
#ifdef CONFIG_SPL_BUILD
if (nand->options & NAND_BUSWIDTH_16)
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 3de30fc..994e235 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -216,11 +216,11 @@
#ifdef CONFIG_NAND
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_BLOCK_SIZE 131072
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
@@ -232,9 +232,8 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME 6
#endif
#endif
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index a9b2714..27db618 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -110,7 +110,6 @@
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_NAND_OMAP_BCH8
#define CONFIG_BCH
/* commands to include */
@@ -298,6 +297,8 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
+#define CONFIG_NAND_OMAP_ECCSCHEME 5
+#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
--
1.8.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
