Define the galois index table offset in chip head file. So user do not need to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh...@atmel.com> --- arch/arm/include/asm/arch-at91/at91sam9x5.h | 6 ++++++ doc/README.atmel_pmecc | 14 -------------- drivers/mtd/nand/atmel_nand.c | 5 ++++- include/configs/at91sam9x5ek.h | 1 - include/configs/sama5d3xek.h | 1 - 5 files changed, 10 insertions(+), 17 deletions(-) diff --git a/arch/arm/include/asm/arch-at91/at91sam9x5.h b/arch/arm/include/asm/arch-at91/at91sam9x5.h index 85e42f5..de9fa50 100644 --- a/arch/arm/include/asm/arch-at91/at91sam9x5.h +++ b/arch/arm/include/asm/arch-at91/at91sam9x5.h @@ -165,6 +165,12 @@ #define ATMEL_ID_UHP ATMEL_ID_UHPHS /* + * PMECC table in ROM + */ +#define ATMEL_PMECC_INDEX_OFFSET_512 0x8000 +#define ATMEL_PMECC_INDEX_OFFSET_1024 0x10000 + +/* * at91sam9x5 specific prototypes */ #ifndef __ASSEMBLY__ diff --git a/doc/README.atmel_pmecc b/doc/README.atmel_pmecc index b483744..41f3bd7 100644 --- a/doc/README.atmel_pmecc +++ b/doc/README.atmel_pmecc @@ -19,17 +19,6 @@ To use PMECC in this driver, the user needs to set: It can be 2, 4, 8, 12 or 24. 2. The PMECC sector size: CONFIG_PMECC_SECTOR_SIZE. It only can be 512 or 1024. - 3. The PMECC index lookup table's offsets in ROM code: CONFIG_PMECC_INDEX_TABLE_OFFSET. - In the chip datasheet section "Boot Stragegies", you can find - two Galois Field Table in the ROM code. One table is for 512-bytes - sector. Another is for 1024-byte sector. Each Galois Field includes - two sub-table: indext table & alpha table. - In the beginning of each Galois Field Table is the index table, - Alpha table is in the following. - So the index table's offset is same as the Galois Field Table. - - Please set CONFIG_PMECC_INDEX_TABLE_OFFSET correctly according the - Galois Field Table's offset base on the sector size you used. Take AT91SAM9X5EK as an example, the board definition file likes: @@ -38,7 +27,4 @@ Take AT91SAM9X5EK as an example, the board definition file likes: #define CONFIG_ATMEL_NAND_HW_PMECC 1 #define CONFIG_PMECC_CAP 2 #define CONFIG_PMECC_SECTOR_SIZE 512 -#define CONFIG_PMECC_INDEX_TABLE_OFFSET 0x8000 -NOTE: If you use 1024 as the sector size, then need set 0x10000 as the - CONFIG_PMECC_INDEX_TABLE_OFFSET diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 3bfbaf8..139a479 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -653,7 +653,10 @@ static int atmel_pmecc_nand_init_params(struct nand_chip *nand, cap = host->pmecc_corr_cap = CONFIG_PMECC_CAP; sector_size = host->pmecc_sector_size = CONFIG_PMECC_SECTOR_SIZE; - host->pmecc_index_table_offset = CONFIG_PMECC_INDEX_TABLE_OFFSET; + if (host->pmecc_sector_size == 512) + host->pmecc_index_table_offset = ATMEL_PMECC_INDEX_OFFSET_512; + else + host->pmecc_index_table_offset = ATMEL_PMECC_INDEX_OFFSET_1024; MTDDEBUG(MTD_DEBUG_LEVEL1, "Initialize PMECC params, cap: %d, sector: %d\n", diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h index ee6e3fc..4364026 100644 --- a/include/configs/at91sam9x5ek.h +++ b/include/configs/at91sam9x5ek.h @@ -137,7 +137,6 @@ #define CONFIG_ATMEL_NAND_HW_PMECC 1 #define CONFIG_PMECC_CAP 2 #define CONFIG_PMECC_SECTOR_SIZE 512 -#define CONFIG_PMECC_INDEX_TABLE_OFFSET 0x8000 #define CONFIG_MTD_DEVICE #define CONFIG_CMD_MTDPARTS diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h index c13e983..67f8180 100644 --- a/include/configs/sama5d3xek.h +++ b/include/configs/sama5d3xek.h @@ -142,7 +142,6 @@ #define CONFIG_ATMEL_NAND_HW_PMECC #define CONFIG_PMECC_CAP 4 #define CONFIG_PMECC_SECTOR_SIZE 512 -#define CONFIG_PMECC_INDEX_TABLE_OFFSET ATMEL_PMECC_INDEX_OFFSET_512 #define CONFIG_CMD_NAND_TRIMFFS #endif -- 1.7.9.5 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot