On 10/31/2012 1:00 PM, Daniel Mack wrote:
> cc devicetree-discuss. Here's a reference to the full thread:
>
> http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/145221/
>
> On 26.10.2012 20:39, Stephen Warren wrote:
>> On 10/24/2012 03:47 AM, Daniel Mack wrote:
>>> Hi,
>>>
>>> a project I'm
On Fri, Oct 26, 2012 at 09:24:11AM +0200, Daniel Mack wrote:
> On 26.10.2012 02:53, David Gibson wrote:
> > On Thu, Oct 25, 2012 at 10:46:32PM +0200, Wolfgang Denk wrote:
> >> Dear Daniel,
> >>
> >> In message <50893633.6070...@gmail.com> you wrote:
> >>>
> >>> Overwrites must be addressed in the f
At some point, a confusion arose about the use of the bit
definitions in host_caps for bus widths, and the value
in ext_csd. By coincidence, a simple shift could convert
between one and the other:
MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0
MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1
MMC_MODE_8B
On 10/31/2012 6:36 PM, Stephen Warren wrote:
> On 10/31/2012 05:56 PM, Mitch Bradley wrote:
>> On 10/31/2012 1:00 PM, Daniel Mack wrote:
>>> cc devicetree-discuss. Here's a reference to the full thread:
>>>
>>> http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/145221/
>>>
>>> On 26.10.2012 2
board configuration file is included before asm/config_mpc85xx.h.
however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h.
it will never take effective in the board configuration file for
this kind of code :
#ifdef CONFIG_FSL_SATA_V2
...
#endif
To solve this problem, move CONFIG_FSL_SAT
Hello Stephen,
On 31.10.2012 17:25, Stephen Warren wrote:
On 10/31/2012 09:56 AM, Simon Glass wrote:
Hi Stephen,
On Wed, Oct 31, 2012 at 8:41 AM, Stephen Warren wrote:
On 10/31/2012 12:00 AM, Heiko Schocher wrote:
Hello Stephen,
On 30.10.2012 23:32, Stephen Warren wrote:
On 10/30/2012 11:
Hi Andy,
It's working fine on my environment.
Tested-by: Jaehoon Chung
Best Regards,
Jaehoon Chung
On 11/01/2012 02:02 PM, Andy Fleming wrote:
> At some point, a confusion arose about the use of the bit
> definitions in host_caps for bus widths, and the value
> in ext_csd. By coincidence, a si
On 01.11.2012 04:26, David Gibson wrote:
> On Fri, Oct 26, 2012 at 09:24:11AM +0200, Daniel Mack wrote:
>> I would especially like to know where such a new functionality should
>> live, which data types it should operate on and what would be an
>> appropriate name for it.
>
> So.. the first thoug
On 10/31/2012 07:21 PM, Alejandro Mery wrote:
> the upcoming sunxi (allwinner a10/a13) platform enables zfs
> by default, and using linaro's hf -msoft-float makes the build
> fail because this u64 division.
>
> Signed-off-by: Alejandro Mery
Acked-by: Stefan Roese
Thanks,
Stefan
___
Signed-off-by: Josh Wu
---
arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c | 12
arch/arm/cpu/arm926ejs/at91/cpu.c| 11 +++
arch/arm/include/asm/arch-at91/at91_dbu.h|4
arch/arm/include/asm/arch-at91/at91sam9x5.h |1 -
4 files c
This patch series adds ANSI terminal Bootmenu command. It use generic menu
code for creating menu structures, but use own functions for drawing menu on
ANSI terminal. First patch modify generic menu code for using other functions
for printing and choosing menu entry, second patch is bootmenu comman
* In menu_interactive_choice can be used user specified function
item_data_choice (instead hardcoded function which read input
from standard input)
* Added option to specify user data for menu
* menu_display_statusline will pass pointer to user data
(instead pointer to menu)
* This patch i
This patch adding new simple command clear which clear ANSI terminal.
Signed-off-by: Pali Rohár
Cc: Marcel Mol
---
This patch was in Nokia RX-51 patch series (v2).
Changes since RX-51 patch v2:
- Removed from include/config_cmd_all.h
- Removed ANSI escape codes (now in BootMenu command patc
This patch adding ANSI terminal bootmenu command. It is extension to generic
menu which provide output for ANSI terminals.
Signed-off-by: Pali Rohár
---
Changes in v2:
- Added commit message
- Removed bootmenu from include/config_cmd_all.h
- Moved ANSI escape codes from include/common.h to
* default bootmenu entries:
attached kernel, internal eMMC memory, external SD card, u-boot boot order
* in CONFIG_PREBOOT try load bootmenu.scr from first FAT partition of internal
eMMC memory (also known as MyDocs) which (should) overwrite default bootmenu
entries
* when keyboard sl
Dear Andy Fleming,
> On Wed, Oct 31, 2012 at 9:32 PM, Marek Vasut wrote:
> > Dear Joe Hershberger,
> >
> >> When building in parallel, make sure that we look up the children
> >> based on the the actual process group id instead of just assuming
> >> that the MAKEALL pid is the process group id.
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/01/12 07:35, Marek Vasut wrote:
> Dear Andy Fleming,
>
>> On Wed, Oct 31, 2012 at 9:32 PM, Marek Vasut
>> wrote:
[snip]
>>> btw. is it possible to improve the u-boot build process
>>> parallelization?
>>
>> In what way?
>
> I recall someone
On Thu, Nov 1, 2012 at 3:13 AM, Roy Zang wrote:
> board configuration file is included before asm/config_mpc85xx.h.
> however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h.
> it will never take effective in the board configuration file for
> this kind of code :
>
> #ifdef CONFIG_FSL_SATA
On Thu, Nov 1, 2012 at 11:20 AM, Tabi Timur-B04825 wrote:
>
>> To solve this problem, move CONFIG_FSL_SATA_V2 to board
>> configuration header file.
>
> http://patchwork.ozlabs.org/patch/126958/
To be clear, I think you should say in the patch description that your
patch effectively reverts mine.
Hello,
Does anyone have any experience with PCIe on an i.MX6 processor (in
particular the i.MX6 Solo)?
I can access the config space of my PCIe device but can't seem to get its
BARs mapped in properly. I thought I had the viewports set up but when I
try to access the space, I just get a processor
Remove the hard-coded bootfile handler and use a callback instead
Signed-off-by: Joe Hershberger
---
common/cmd_nvedit.c| 9 -
include/env_callback.h | 1 +
net/net.c | 17 +
3 files changed, 18 insertions(+), 9 deletions(-)
diff --git a/common/cmd_nv
Use the variable access flags to implement the protection for ethaddr
and serial# instead of hard-coding them.
Signed-off-by: Joe Hershberger
---
common/env_flags.c | 19 ---
include/env_flags.h | 22 ++
tools/env/fw_env.c | 17 -
3 files ch
Remove the hard-coded baudrate handler and use a callback instead
Signed-off-by: Joe Hershberger
---
common/cmd_nvedit.c | 47 -
drivers/serial/serial.c | 70 +
include/env_callback.h | 1 +
3 files changed, 7
When a variable with a registered callback is inserted, deleted, or
overwritten the callback is called and gives the system an opportunity
to do something in response to the change. It also has the opportunuty
to reject the change by returning non-zero.
The flags on variables can control their t
isspace() and strim() are not in the typical user-mode string.h, so
put them in a separate compilation unit so that they can be built into
tools that need them independent of the other common string functions.
This allows code shared by u-boot and the linux user-mode tools to link.
Signed-off-by:
Similar to the env callback command, this will show details about the
options available, the static list, and the currently active variables.
Signed-off-by: Joe Hershberger
---
README | 1 +
common/cmd_nvedit.c | 56 +
common/env
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger
---
common/console.c | 23 +++
doc/README.silen
The callbacks can be bound, but are otherwise invisible. Add a command
to show what callbacks are available.
Signed-off-by: Joe Hershberger
---
README | 1 +
common/cmd_nvedit.c | 77 +
2 files changed, 78 insertions(+)
diff --
Remove the hard-coded console handler and use a callback instead
Signed-off-by: Joe Hershberger
---
common/cmd_nvedit.c| 33 +++--
common/console.c | 44
include/env_callback.h | 1 +
3 files changed, 48 inserti
Move the read of the old value to inside the check function. In some
cases it can be avoided all together and at the least the code is only
called from one place.
Also name the function and the callback to more clearly describe what
it does.
Pass the ENTRY instead of just the name for direct acc
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address. Call
env_acl_validate_setenv_params() from setenv() in fw_env.c.
If the entry is not found in the env .flags, then look in the static
one. This allows the env to override the static definitions,
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberge
Remove the hard-coded loadaddr handler and use a callback instead
Signed-off-by: Joe Hershberger
---
common/cmd_nvedit.c| 12
common/image.c | 21 +
include/env_callback.h | 1 +
3 files changed, 22 insertions(+), 12 deletions(-)
diff --git a/commo
The same chunk of code was replicated in two places and the following
changes will make that chunk grow a bit, so combine into a static func.
Signed-off-by: Joe Hershberger
---
lib/hashtable.c | 71 ++---
1 file changed, 37 insertions(+), 34 d
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address.
If the entry is not found in the env ".flags", then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environme
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger
---
arch/arm/lib/board.c| 4 +---
arch/m68k/lib/board.c | 3 +--
arch/microblaze/lib/board.c | 4 +---
arch/powerpc/cpu/mpc85xx/mp.c |
Use a flag in hsearch_r for insert mode passed from import to allow the
behavior be different based on use.
Signed-off-by: Joe Hershberger
---
Changes in v3:
- Rebase onto Gerlando Falauto's env patches
- Refactor himport_r() and hsearch_r()'s parameters
common/cmd_nvedit.c | 17 ---
Add support for read-only, write-once, and change-default.
Signed-off-by: Joe Hershberger
---
README| 13 -
common/cmd_nvedit.c | 31 --
common/env_common.c | 18 ++
common/env_flags.c| 153 --
include/en
Add support for per-variable callbacks to the "hashtable" functions.
Signed-off-by: Joe Hershberger
---
Changes in v3:
- Use Marek's linker lists instead of implementing it directly
- Rebase onto latest master
- Add flags parameter to callbacks
- Implement reverse search in env_attr_lookup()
- Fi
On 11/01/2012 01:42 AM, Heiko Schocher wrote:
> Hello Stephen,
>
> On 31.10.2012 17:25, Stephen Warren wrote:
>> On 10/31/2012 09:56 AM, Simon Glass wrote:
>>> Hi Stephen,
>>>
>>> On Wed, Oct 31, 2012 at 8:41 AM, Stephen
>>> Warren wrote:
On 10/31/2012 12:00 AM, Heiko Schocher wrote:
> H
On Thu, Nov 1, 2012 at 2:32 PM, Carolyn Smith wrote:
> Hello,
>
> Does anyone have any experience with PCIe on an i.MX6 processor (in
> particular the i.MX6 Solo)?
>
> I can access the config space of my PCIe device but can't seem to get its
> BARs mapped in properly. I thought I had the viewports
The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.
It
Yes, I have the PCI clocks on. I can read the config space and can see the
PCIe bus traffic using a logic analyzer when I do so. When I try reading
memory or I/O space, I don't see any bus traffic.
Thanks,
Carolyn
On Thu, Nov 1, 2012 at 11:18 AM, Fabio Estevam wrote:
> On Thu, Nov 1, 2012 at 2:
The documented work-around for P4080 erratum SERDES-9 has been updated.
It is now compatible with the work-around for erratum A-4580.
This requires adding a few bitfield macros for the BnTTLCRy0 register.
Signed-off-by: Timur Tabi
---
arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c | 20 +++
Hi,
I used to have a working setup using U-Boot 2009.03 before upgrading to U-Boot
2012.07. The problem I'm facing is related to the escaping policies of
lib/hashtable.c.
What I did before was for example having something like this in my default
environment:
bootcmd=run first_boot
first_boot=
Dear Mats Kärrman,
In message you wrote:
>
> I used to have a working setup using U-Boot 2009.03 before upgrading to
> U-Boot 2012.07. The problem I'm facing is related to the escaping policies of
> lib/hashtable.c.
>
> What I did before was for example having something like this in my defaul
Hi Wolfgang,
On Wed, Oct 31, 2012 at 5:04 PM, Simon Glass wrote:
> Hi Wolfgang,
>
> On Wed, Oct 31, 2012 at 4:40 PM, Wolfgang Denk wrote:
>> Dear Simon,
>>
>> In message
>> you
>> wrote:
>>>
>>> >> These changes are required to the patman libraries. This is not a proper
>>> >> patch yet, just
Hi Andy / Tom,
On Wed, Oct 31, 2012 at 9:17 PM, Andy Fleming wrote:
> On Wed, Oct 31, 2012 at 8:18 PM, Tom Rini wrote:
>> On Wed, Oct 31, 2012 at 05:11:51PM -0700, Simon Glass wrote:
>>
>> [snip]
>>> Also rather than running with 'make -j40' or whatever, it uses 'make
>>> -j1' but with 40 thread
This allows the default console to be specified as the nulldev. This is
specifically helpful when the real serial console's init() cannot run
early in the boot process. When the init can be run, then the console
can be switched to the real device using the std* env vars.
Signed-off-by: Joe Hersh
Each serial device is added as a console device. There was also the
"serial" device that points to the most-recently-assigned-to-some-
console-handle device. This can be confusing. Instead, only show the
actual serial devices.
Signed-off-by: Joe Hershberger
---
common/console.c | 37 +
On 07/30/2012 12:53 AM, Simon Glass wrote:
> This enables NAND support for the Seaboard.
> diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h
> #include "tegra20-common-post.h"
>
> +/* NAND support */
> +#define CONFIG_CMD_NAND
> +#define CONFIG_TEGRA_NAND
> +
> +/* Max numbe
From: Stephen Warren
TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board co
If sub-page reads are supported, this will save reading unneeded data
Signed-off-by: Joe Hershberger
---
drivers/mtd/ubi/io.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/mtd/ubi/io.c b/drivers/mtd/ubi/io.c
index 8423894..23660e3 100644
--- a/drivers/mtd/ubi/io.c
+
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).
Signed-off-by: Joe Hershberger
---
drivers/mtd/nand/nand_base.c | 9 +++--
include/linux/mtd/nand.h | 7 ---
2 files changed, 11 insertions(+), 5 deletions(-)
diff --g
Am Donnerstag, den 01.11.2012, 15:57 -0600 schrieb Stephen Warren:
> On 07/30/2012 12:53 AM, Simon Glass wrote:
> > This enables NAND support for the Seaboard.
>
> > diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h
>
> > #include "tegra20-common-post.h"
> >
> > +/* NAND sup
Hi,
On Thu, Nov 1, 2012 at 4:13 PM, Lucas Stach wrote:
> Am Donnerstag, den 01.11.2012, 15:57 -0600 schrieb Stephen Warren:
>> On 07/30/2012 12:53 AM, Simon Glass wrote:
>> > This enables NAND support for the Seaboard.
>>
>> > diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h
>
Hi Stephen,
Am Donnerstag, den 01.11.2012, 16:14 -0600 schrieb Stephen Warren:
> From: Stephen Warren
>
> TrimSlice's USB1 port has two purposes; it either acts as a device port
> hosting Tegra's USB recovery protocol, or acts as a host port connected
> to the internal USB->SATA bridge chip, whi
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/01/12 14:01, Simon Glass wrote:
> Hi Andy / Tom,
>
> On Wed, Oct 31, 2012 at 9:17 PM, Andy Fleming
> wrote:
>> On Wed, Oct 31, 2012 at 8:18 PM, Tom Rini wrote:
>>> On Wed, Oct 31, 2012 at 05:11:51PM -0700, Simon Glass wrote:
>>>
>>> [snip]
>>
On 11/01/2012 05:17 PM, Lucas Stach wrote:
> Hi Stephen,
>
> Am Donnerstag, den 01.11.2012, 16:14 -0600 schrieb Stephen Warren:
>> From: Stephen Warren
>>
>> TrimSlice's USB1 port has two purposes; it either acts as a device port
>> hosting Tegra's USB recovery protocol, or acts as a host port co
Am Donnerstag, den 01.11.2012, 17:30 -0600 schrieb Stephen Warren:
> On 11/01/2012 05:17 PM, Lucas Stach wrote:
> > Hi Stephen,
> >
> > Am Donnerstag, den 01.11.2012, 16:14 -0600 schrieb Stephen Warren:
> >> From: Stephen Warren
> >>
> >> TrimSlice's USB1 port has two purposes; it either acts as
Add support for CONSOLE_MUX to tegra-kbc driver. This requires
adding a flag to struct keyb to know the driver has already been
initialized so if we try to initialize it again we can just return
success. Also call into iomux_doenv() from drv_keyboard_init to
re-evaluate the stdin string.
Signed-
It is good to have these functions written in C instead of assembler,
but with -O0 the cache_disable() function doesn't return. Rather than
revert to assembler, this fix just forces this to be built with -O2.
Signed-off-by: Simon Glass
---
arch/arm/lib/cache-cp15.c | 10 ++
1 files cha
From: Gabe Black
It may be necessary to know where the TLB area ends as well as where it
starts. This allows board code to complete a secure memory erase without
destroying the page tables.
Signed-off-by: Gabe Black
Signed-off-by: Simon Glass
---
arch/arm/include/asm/global_data.h |1 +
a
This option displays board info after stdio is running, so that it will
appear on the LCD. If it is displayed earlier, the board info will appear
on the serial console but not on the LCD.
Signed-off-by: Simon Glass
---
README |9 +
arch/arm/lib/board.c | 19 +
This option delays loading of the environment until later, so that only the
default environment will be available to U-Boot.
This can address the security risk of untrusted data being used during boot.
When CONFIG_DELAY_ENVIRONMENT is defined, it is convenient to have a
run-time way of enabling l
From: Tom Wai-Hong Tam
SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.
Signed-off-by: Tom Wai-Hong Tam
Signed-off-by: Simon Glass
---
arch/arm/lib/Makefile |5 +++--
1 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/a
We want to use the fdt inside board_early_init_f(), so check for its
presence earlier in the pre-reloc init sequence.
Signed-off-by: Simon Glass
---
arch/arm/lib/board.c |7 +++
1 files changed, 3 insertions(+), 4 deletions(-)
diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c
ind
From: Arun Mankuzhi
In Cortex-A15 architecture, when we run cache invalidate
the cache clean operation executes automatically.
So if there are any dirty cache lines before disabling the L2 cache
these will be synchronized with the main memory when
invalidate_dcache_all() runs in the last part of
From: Taylor Hutt
The two modified lines were indented with spaces.
They are now indented with tabs.
Signed-off-by: Taylor Hutt
Signed-off-by: Simon Glass
---
arch/arm/lib/board.c |4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/lib/board.c b/arch/arm/lib/b
The timer may be inited in arch_cpu_init() so it is not safe to make a
bootstage mark before this is called. Arrange the code to fix this.
We now get a correct time for board_init_f:
Timer summary in microseconds:
MarkElapsed Stage
0 0 reset
100,000100,000
Some boards want to report more than just memory size. For example, it
might be useful to display the memory type (DDR2, DDR3) or manufacturer.
Add a weak function to support this requirement.
Any example of the DRAM: output is below, just for illustration:
U-Boot 2011.12-02470-gd64a0f8-dirty (S
Dear Allen Martin,
> Add support for CONSOLE_MUX to tegra-kbc driver. This requires
> adding a flag to struct keyb to know the driver has already been
> initialized so if we try to initialize it again we can just return
> success. Also call into iomux_doenv() from drv_keyboard_init to
> re-evalu
Best Regards
Jerry Huang
> -Original Message-
> From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de]
> On Behalf Of Andy Fleming
> Sent: Thursday, November 01, 2012 12:09 PM
> To: Lukasz Majewski
> Cc: Jaehoon Chung; Marek Vasut; Lei Wen; u-boot@lists.denx.de
> Subje
Hi,
Andy has sent the patch related with this problem.
Check the patch "[RFC] mmc: Properly determine maximum supported bus width"
Best Regards,
Jaehoon Chung
>> decide the best workaround was to cripple our controller by eliminating
>> support for 8-bit?
> I see 12bit width when using mmcinfo, t
On Thu, Nov 1, 2012 at 3:14 PM, Stephen Warren wrote:
> From: Stephen Warren
>
> TrimSlice's USB1 port has two purposes; it either acts as a device port
> hosting Tegra's USB recovery protocol, or acts as a host port connected
> to the internal USB->SATA bridge chip, which may in turn be connecte
Thanks, Jaehoon, I saw it.
Best Regards
Jerry Huang
> -Original Message-
> From: Jaehoon Chung [mailto:jh80.ch...@samsung.com]
> Sent: Friday, November 02, 2012 10:03 AM
> To: Huang Changming-R66093
> Cc: Andy Fleming; Lukasz Majewski; Jaehoon Chung; Marek Vasut; u-
> b...@lists.denx.de;
Make setexpr accept a 2 parameter variant that will simply load a value
into a variable. This is useful for loading a value from memory.
Signed-off-by: Joe Hershberger
---
Changes in v2:
- Replaced memory get command with option to setexpr
common/cmd_setexpr.c | 19 ---
1 file
Hi Marek,
On Wed, Oct 31, 2012 at 4:39 PM, Marek Vasut wrote:
> Dear Simon Glass,
>
>> This adds a docbook template for fs, and makes CBFS use it.
>>
>> Problems (advise please as I have enough 500pp books in my bookshelf):
>>
>> 1. It requires the function names to be repeated. I would like to d
Hi,
On Wed, Oct 31, 2012 at 6:22 PM, Tom Rini wrote:
> On Wed, Oct 31, 2012 at 11:41:20PM +0100, Wolfgang Denk wrote:
>> Dear Simon Glass,
>>
>> In message <1350087972-1581-6-git-send-email-...@chromium.org> you wrote:
>> > From: Gabe Black
>> >
>> > This change adds CBFS support and some comman
UBI can mount volumes by name or number The current code forces you
to name the volume by prepending every name with "ubi:".
>From fs/ubifs/super.c
* There are several ways to specify UBI volumes when mounting UBIFS:
* o ubiX_Y- UBI device number X, volume Y;
* o ubiY - UBI device num
The ip is stored in network order, so we can't test it in host order.
Signed-off-by: Joe Hershberger
---
net/link_local.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/link_local.c b/net/link_local.c
index d52f13a..8a8f605 100644
--- a/net/link_local.c
+++ b/net/link_lo
Dear Simon Glass,
> Hi Marek,
>
> On Wed, Oct 31, 2012 at 4:39 PM, Marek Vasut wrote:
> > Dear Simon Glass,
> >
> >> This adds a docbook template for fs, and makes CBFS use it.
> >>
> >> Problems (advise please as I have enough 500pp books in my bookshelf):
> >
> >> 1. It requires the functio
Dear Huang Changming-R66093,
> Thanks, Jaehoon, I saw it.
>
> Best Regards
> Jerry Huang
I wonder if you're just making fun of all of us or what you're actually trying
to acomplish here with the constant top-posting ... I'm really stunned :-(
> > -Original Message-
> > From: Jaehoon Ch
Hi
I analyzed the code and put some prints to find the below mentioned
behavior.
The ARP packet is being received by ENC28J60 but when it reaches the
software pkt format is not correct.
A 0 is being appended to the packet.
After analysis I found this errata mentioned in ENC28J60 errata sheet i
84 matches
Mail list logo
