Hi I analyzed the code and put some prints to find the below mentioned behavior. The ARP packet is being received by ENC28J60 but when it reaches the software pkt format is not correct. A 0 is being appended to the packet.
After analysis I found this errata mentioned in ENC28J60 errata sheet is not applied for the initial case (for the first packet). Later on it is fine. I have made the changes and I need to test it today night after office. Module: Memory (Ethernet Buffer) The receive hardware may corrupt the circular receive buffer (including the Next Packet Pointer and receive status vector fields) when an even value is programmed into the ERXRDPTH:ERXRDPTL registers. Work around Ensure that only odd addresses are written to the ERXRDPT registers. Assuming that ERXND contains an odd value, many applications can derive a suitable value to write to ERXRDPT by subtracting one from the Next Packet Pointer (a value always ensured to be even because of hardware padding) and then compensating for a potential ERXST to ERXND wraparound. Assuming that the receive buffer area does not span the 1FFFh to 0000h memory boundary, the logic in Example 1 will ensure that ERXRDPT is programmed with an odd value Are you aware of any such change required in the ENC28J60 uboot code. Kindly let me know if anybody has faced such issue akdas75 wrote: > > Hi > > As per your suggestion I tried 2012.10 > Still the result is same. But it shows receive length is zero. > > I have attached the logs > I have attached the changes to make ethernet work. > > As I am new to this forum I hope you said me to reply to this mailing > list. > > Ajoy http://old.nabble.com/file/p34620403/uboot.txt uboot.txt > http://old.nabble.com/file/p34620403/uboot.patch uboot.patch > > > > akdas75 wrote: >> >> hi >> >> No I dont have any firewall running. >> I have enabled to receive all packets [] >> >> i am using the uboot version 2011.03 with the following changes. >> But i think it will not affect the ping functionality. >> >> Any help. I will try putting more logs and pointing the issue. >> >> attached is the patch >> >> Ajoy >> >> >> >> akdas75 wrote: >>> >>> hi Anatolij >>> I tried your suggestion >>> I generate a macid from uboot/tools/gen_eth_addr. >>> Still the ping says "host not alive" >>> >>> I have attached the uboot log >>> and also the wireshark snapshot on the host >>> >>> host : 192.168.1.101 >>> development board : 192.168.1.100 >>> >>> Ajoy >>> http://old.nabble.com/file/p34610904/uboot_log_1.txt uboot_log_1.txt >>> http://old.nabble.com/file/p34610904/snap_wireshark_host.JPG >>> snap_wireshark_host.JPG >>> >>> akdas75 wrote: >>>> >>>> Hi http://old.nabble.com/file/p34608548/uboot-log.rtf uboot-log.rtf >>>> >>>> I am using beagle board C4 with zippy expansion board. >>>> I am able to do NFS at the kernel level. >>>> I want to o tftp at the u-boot level. >>>> my beagle board is connected to the host via cross ethernet cable. >>>> the phy chip is enc28j60. >>>> when i ping the host it says host not alive. >>>> >>>> i have attached the env variables >>>> >>>> please help >>>> >>>> >>> >>> >> http://old.nabble.com/file/p34615656/u-boot.patch u-boot.patch >> > > -- View this message in context: http://old.nabble.com/ping-failed--host-192.168.1.101-is-not-alive-tp34608548p34631908.html Sent from the Uboot - Users mailing list archive at Nabble.com. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
