I have not had any issues with either the FX or Radian. I have had lots of
bad gennys fields failed, over under voltage, Check programming possible
overloading of the genny
Jerry
On Mar 18, 2015 4:39 PM, "jay peltz" wrote:
> HI All,
>
> My question is. are there any known issues with the Radian i
This sounds like the exact same issue with the FX and VFX inverters. Meter the
power quality while under charge - nasty. We found a lot of computerized
control systems on furnaces and boilers would either reject the power and not
power up, or would behave erratically, some would be ok if you pow
Are LED's on dimmers and non dimmers flickering or just dimmer switch
connected lightsi have had problems with LED's on dimmer switches even
with LED specific dimmer switches. ..
Just an idea. ...
On Mar 18, 2015 7:39 PM, "jay peltz" wrote:
> HI All,
>
> My question is. are there any known is
HI All,
My question is. are there any known issues with the Radian interfacing with a
generator?
I have a customer with flickering lights.
The lights are LED ( some dimmer/some on/off)
The generator supplier says that there are lots of problems with the Radian.
I've not heard this and don't bel
We use elite batteries with BMS no problems, the BMS sensor does seem to
run warm we are now setting up 4, 100 Ah banks with no problems so far.
Jerry
On Mar 18, 2015 1:52 PM, "Bruce Erickson" wrote:
> If a communication failure with a single cell (not even an actual fault)
> can cause total batt
Not at all. The EMS boards are well built and are protected under a
cover with the terminals. I have not had any failures of the EMS boards
or any failure to communicate with them.
Larry
On 3/18/15 4:52 PM, Bruce Erickson wrote:
If a communication failure with a single cell (not even an actual
If a communication failure with a single cell (not even an actual fault) can
cause total battery shutdown, does that lead to a lot of nuisance tripping?
Bruce Erickson
Mendocino Solar Service
PO Box 1252
Mendocino, CA 95460
707-937-1701
707-937-1741 fax
br...@mendocinosolar.com
Celebrating 20 Ye
There was a certification update the last year or so where UL standards on
transformers changed. If you have an X240 that came with a 25, then it was
from the old math. The X240s that ship under the new math have 20A
breakers. Like you, I've installed tons of X240s with 25A breakers, but
either
Hi Chris,
Thanks for the recommendation. I received a quote from Comrent$1800
to rent a load for 1 week. Ouch! I'll go with the $10 water elements and
a little fabrication time. I have AH counters and controllers to stop
the discharge.
Thank you,
Larry Crutcher
Starlight Solar Power Sys
Larry,
I've been checking out the [current] viability of Li+ technologies for RE
systems, and I'm encouraged to hear of the success you've apparently had.
What is the typical kWh size of the battery packs you've been putting together?
Are you sourcing the GBS batteries directly from the manufac
Phil
Please confirm i have built lots of ps2 and 4 seams to always have 25's on
the x240 not 20's
Jerry
On Mar 18, 2015 10:04 AM, "Phil Undercuffler" wrote:
> The PSX-240 (independent unit in enclosure) has active cooling, so it has
> a higher capacity and therefore the 25A breaker. The X-240 (b
The PSX-240 (independent unit in enclosure) has active cooling, so it has a
higher capacity and therefore the 25A breaker. The X-240 (bare xformer)
should have a 20A. The good news is, in OutBack Stacking the xformer is
balancing the phases, which since there are inverters on both phases means
th
We're leaning toward the LiFePO4 batteries (low internal resistance) GBS have
a medium high resistance so they warm faster and have a lower C rate
efficiency, were gathering info as we go.. Max Balchowsky
Design Engineer
Golden Bridge Development
1048 Irvine Ave Suite 217
Newport Beach, Ca.
Kevin and Matt,
Good advice from Matt. Just one detail: On the Outback PSX-240 (the
independent unit with enclosure) the output breakers are 25A, not
20A. I suspect that the 2P
breaker for the X-240 would be the same. As the unit often operates
at close to its capacit
Hi Jarmo,
I agree and recognize your urgency in making us aware of the proper use
and charging of Li-ion batteries as well as the dangers of mistreating
them. As an early adopter myself, I am very cautious in my approach even
to the point of refusing to sell to some customers. Lithium battery
Wrenches,
Do you have a favorite brand/model of torque wrenches when assembling
mounts to manufacturer's specs? How do you handle calibration?
TIA,
--
Bill Loesch
Solar 1 - Saint Louis Solar
314 631 1094
-
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.57
16 matches
Mail list logo
