Re: dhcp6leased: problem configuring a public IPv6 address on the external interface

Op za 12 okt 2024 om 00:24 schreef Jason Tubnor : > You would have been getting your external /128 address via ia_na, not > slaac. My ISP is configured the same way. [...] > dhcp6leased only does PD and not NA at this time. In my case, once I > request a PD from the ISP, I can route all traffic

dhcp6leased: problem configuring a public IPv6 address on the external interface

8 em0 vlan4 wg0 vlan5 vlan3 } This doesn't feel right though, but I'm not sure why. I don't know why em1 doesn't get a public IPv6 address from slaacd. Should the external interface get an external IPv6 address from slaacd using router solicitations, and if so, what am I doing wrong here? Regards, Jurjen Oskam

Re: amd64 vmm(4) virtual machine "powers off" instead of rebooting when started with "-B disk"

16:01 schreef Philipp Buehler : > > Am 29.12.2022 15:40 schrieb Jurjen Oskam: > > From the host dmesg I noticed the following line: > > It has been this way since day-1 of -B -- unclear if you want to call > it expected, feature or bug :-) > > Noticed this early on the vagra

amd64 vmm(4) virtual machine "powers off" instead of rebooting when started with "-B disk"

Hi, Today I first started to use vmm(4) virtual machines (on amd64 7.2 with all syspatches applied, dmesg of the host is below). From what I've seen so far I'm quite happy with it, it's very elegant and straightforward how all the components work together. One thing I noticed is that when a VM is

Could "re0: watchdog timeout" be caused by pf queues?

Hi, On my home router, since a year or two I've occasionally seen watchdog timeouts on re0 (which is connected with 1Gbps to a Cisco switch): re0: watchdog timeout They weren't frequent, but when they occurred it was always under high-ish throughput (300-400 Mbps). Yesterday however, one particu

Re: uvn_flush: WARNING: changes to page may be lost

scenario where the msync(2) manpage warns for: "Filesystem operations on a file that is mapped for shared modifications are unpredictable except after an msync()." Thanks for pointing me in this direction, it resulted in an interesting half hour of reading web pages about mmap on several OSes. :) Regards, Jurjen Oskam

Re: uvn_flush: WARNING: changes to page may be lost

n messages like this? (Not counting situations where softupdates are enabled) Regards, Jurjen Oskam

Re: msyscall error during boot

On Thu, Jul 09, 2020 at 06:38:01AM +, mabi wrote: > I just upgraded one of my vmd virtual machine from OpenBSD 6.6 to 6.7 using > sysupgrade and noticed a new msyscall error message I have never seen before > during reboot as you can see below: > > ... > preserving editor files. > starting

Re: [smartmontools] OpenBSD testers required

On Fri, Jun 05, 2020 at 10:52:38AM +0200, Marek Benc wrote: > There's been some changes in the OpenBSD port of smartmontools, > tools for working with S.M.A.R.T diagnostic of hard drives and SSDs, > the platform-specific code was modernized, so it would be quite useful > if people could test these

Re: Offline autoinstall(install.conf)

l(8)). The link you gave describes a good method of doing that, and nowadays it's easier because rdsetroot is part of the base system so you don't even need to build it. Regards, Jurjen Oskam

Forgetting pkg_add -u after sysupgrade can cause ansible msyscall errors

e-2.7.9 and python-3.6.8p0. This caused me to realize I had forgotten to update my packages after doing the sysupgrade... A quick "pkg_add -u" later and my problem was gone. D'oh! So, moral of the story: don't forget to update your packages after a sysupgrade. Regards, Jurjen Oskam

Re: OpenBSD VM on ESXi: uvn_flush: obj=0xfffffd813ee78298, offset=0x33f000. error during pageout.

On Thu, Oct 31, 2019 at 08:01:25AM -, Stuart Henderson wrote: > On 2019-10-30, Jurjen Oskam wrote: > > > > All snapshots I tried up to and including this point did not show the > > problem: > > OpenBSD 6.6-beta (GENERIC.MP) #202: Mon Aug 12 11:01:21 MDT 2019 &g

Re: OpenBSD VM on ESXi: uvn_flush: obj=0xfffffd813ee78298, offset=0x33f000. error during pageout.

On Tue, Oct 29, 2019 at 01:25:10PM -0700, Mike Larkin wrote: > On Tue, Oct 29, 2019 at 09:16:42PM +0100, Jurjen Oskam wrote: [...] > > uvn_flush: obj=0xfd813ee78298, offset=0x33f. error during pageout. > > uvn_flush: WARNING: changes to page may be lost! > > uvn_f

OpenBSD VM on ESXi: uvn_flush: obj=0xfffffd813ee78298, offset=0x33f000. error during pageout.

PCIE" rev 0x01 pci34 at ppb33 bus 34 isa0 at pcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets root on sd0a (afa24b55e438df24.a) swap on sd0b dump on sd0b Regards, Jurjen Oskam

Re: L2TP/IPsec VPN server: trying to force HMAC_SHA in phase 2, but isakmpd keeps offering HMAC_SHA2_256?

y using the -K option (in which case it's certain that policy checking never happens). But now I know better. :) Thanks, Jurjen 2017-03-20 9:33 GMT+01:00 Jurjen Oskam : > Hi Philipp, > > Thank you - this was exactly what I was missing. I have now gotten it to > work by excluding

L2TP/IPsec VPN server: trying to force HMAC_SHA in phase 2, but isakmpd keeps offering HMAC_SHA2_256?

AUTHENTICATION_ALGORITHM" HMAC_SHA # I'm likely to miss something obvious here. Why is isakmpd negotiating HMAC_SHA2_256 instead of HMAC_SHA, as it is configured to do? Any hints would be much appreciated. Thanks, Jurjen Oskam

Re: Cannot set stty parameters and read from /dev/ttyU0

Stuart Henderson spacehopper.org> writes: > > On 2014-01-10, Jurjen Oskam osk.am> wrote: > > Philip Guenther gmail.com> writes: > > > >> Oh, you're running 5.4-stable? I thought you were running -current > >> and was worried there was an

Re: Cannot set stty parameters and read from /dev/ttyU0

(and leave everything else the same), everything works as expected: no hangs at all, and interrupting a read is no problem. I'm sorry, but I don't know which hang you fixed in October. With this information, do you think it's the same hang? Thanks, Jurjen Oskam

Re: Cannot set stty parameters and read from /dev/ttyU0

Philip Guenther gmail.com> writes: > > On Thu, Jan 9, 2014 at 8:20 AM, Jurjen Oskam osk.am> wrote: > > OK, I've got it to work using a /dev/cua* device. I still have problems > > with processes not exiting though. Since this machine has real com > > ports, I

Re: Cannot set stty parameters and read from /dev/ttyU0

e process to just exit and release cua01 after I killed it. Regards, Jurjen Oskam

Re: Cannot set stty parameters and read from /dev/ttyU0

t coming back, at least not until I Ctrl-C the Perl script: 15860 perl 1389125426.222462 CALL open(0x12f6694a1d70,0) 15860 perl 1389125426.222465 NAMI "/dev/ttyU0" 15860 perl 1389125451.261414 PSIG SIGINT SIG_DFL Again, open() doesn't seem to return. Am I doing something wrong here? Regards, Jurjen Oskam

Cannot set stty parameters and read from /dev/ttyU0

sconnecting the SSH session doesn't work: joskam 21226 0.0 0.0 180 152 p0 D+ 3:56PM0:00.00 stty -f /dev/ttyU0 joskam 22302 0.0 0.0 236 176 p1- IE 3:54PM0:00.00 (cat) I did read the manual pages, but I probably overlooked something. How can I set the c

Re: dhclient, resolv.conf

supersede domain-name-servers 192.168.1.1; supersede domain-name ""; Regards, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Seeking inexpensive RAID 1 hardware recommendation

works extremely well. It wasn't hard to find over here, and not expensive. I just visited a reputable Web shop, searched for EH417AA and that was basically it. Regards, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Auto Logout Idle Users

ce, not a security measure: $ TMOUT=600 $ readonly TMOUT $ exec perl -e 'delete $ENV{TMOUT} ; exec "/bin/ksh";' $ echo $TMOUT 0 $ -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

mt_soname mbufs keep increasing steadily, where can I look?

) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x25 lm2 at wbsio0 port 0x290/8: W83627DHG lm1 detached mtrr: Pentium Pro MTRR support softraid0 at root root on sd1a swap on sd1b dump on sd1b WARNING: / was not properly unmounted -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: TRIM support?

nd my almost-always-quite-low write response times. :) -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: trouble showing a kernel dmesg

pect the hardware) but you've guessed it: in that case the dmesg doesn't survive the reboot... -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Why does dhclient-script set a route to 127.0.0.1?

ipt goes out of its way to set this route. Could someone point me in the right direction? I'd like to understand the effects of setting (or not setting) such a route... Regards, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Hardware problem? amd64 system sometimes just resets with MP kernel, dmesg buffer doesn't survive.

RAM ECC PC2-6400CL5 usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at pcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x25 lm2 at wbsio0 port 0x290/8: W83627DHG lm1 detached mtrr: Pentium Pro MTRR support softraid0 at root root on sd1a swap on sd1b dump on sd1b Thank you, -- Jurjen Oskam

Re: how to fresh raidframe install on an already raidframe system?

within. Once happy, I can set the boot.conf of the two disks to the autoconfig RAIDframe enabled kernel, which will then load from one of the normal partitions, but once started will use the root filesystem in the RAID partition. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: bioctl's "Device" name inconsistent with dmesg device name: is that expected?

27;t have time to work on it right away so I need reminder :-) Sure, I've just sent in my report and it's now registered under number 6269. Thanks for the quick reply, and if there's something I can do just let me know. Regards, -- Jurjen Oskam

bioctl's "Device" name inconsistent with dmesg device name: is that expected?

t 0x3f8/8 irq 4: ns16550a, 16 byte fifo com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x25 lm2 at wbsio0 port 0x290/8: W83627DHG lm1 detached mtrr: Pentium Pro MTRR support softraid0 at root root on sd1a swap on sd1b dump on sd1b Thanks, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Kernel log message without a \n

ot send Michael MIC Failure reports as recommended since -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

ahci0: unrecoverable errors (IS: 8000000), disabling port.

ity: can't read stripe. Could not verify parity. raid0: Error re-writing parity! ral0: Michael MIC failureClosing the opened device: /dev/sd3l About to (re-)open the device for rebuilding: /dev/sd3l RECON: Initiating in-place reconstruction on row 0 col 0 -> spare at row 0 col 0. Quiescence reached... Thanks, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: 200g harddisk after newfs = Available 174g?

/second, and not 1073741824 bits/second. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Memory on 4.5 again

(99% in use) > > 0 requests for memory denied > > 0 requests for memory delayed > > 0 calls to protocol drain routines > > > > 150 MB for network seems a bit much to me, especially since I can literally > > watch that number grow. The system has 3 wired ethernet in

Re: mount point busy, can't find process holding it

see my signature in almost every unix command :]) > > amaaq$ sudo fstat -f /adata > USER CMD PID FD MOUNTINUM MODE R/WSZ|DV > > no luck Are you sure you haven't mounted anything else somewhere in the filesystem you're trying to unmount? You

Re: bash for root?

andy when you want the ERR trap to fire when any single command of a set of piped commands exits non-zero. (If there's a better way of doing things, I'd love to hear about it...) -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

ral0: "ping: sendto: No buffer space available"

lm1 at wbsio0 port 0x290/8: W83697HF fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec Kernelized RAIDframe activated raid0 at root: (RAID Level 1) total number of sectors is 154534656 (75456 MB) as root softraid0 at root swapmount: no device -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Nintendo Wii seems to be unhappy with a ral in hostap mode

yte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 lpt0 at isa0 port 0x378/4 irq 7 wbsio0 at isa0 port 0x2e/2: W83697HF rev 0x12 lm1 at w

How to (help) diagnose a system hang?

at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 lpt0 at isa0 port 0x378/4 irq 7 wbsio0 at isa0 port 0x2e/2: W83697HF rev 0x12 lm1 at wbsio0 port 0x290/8: W83697HF fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec Kernelized RAIDframe activated raid0 at root: (RAID Level 1) total number of sectors is 154534656 (75456 MB) as root softraid0 at root swapmount: no device -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: ral(4) hostap plea

1, address 00:11:6b:3d:7f:6a ral0: MAC/BBP RT2561C, RF RT2527 Try attaching (if you haven't already) a high quality external antenna. This made a world of difference in my case. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Environment variables

py-pasted this program from somewhere on the Web. You'll not be seeing me near any C code with any significant value anytime soon. :) But thanks for the tip. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Environment variables

On Fri, Apr 18, 2008 at 04:21:08PM +0200, Almir Karic wrote: > On Fri, Apr 18, 2008 at 3:20 PM, Jurjen Oskam <[EMAIL PROTECTED]> wrote: > > So ps does show FOO, *and* it shows the value of FOO changing after > > ten seconds. > > > > what is so weird about it

Environment variables

s does pick up newly set environment variables. Is this behaviour implementation dependent? Thanks, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: USB speed (umass): what should I expect?

xample "MAKEDEV all" took 45 seconds without soft updates, and 2 seconds with soft updates. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

USB speed (umass): what should I expect?

b1 port 1 configuration 1 interface 0 "OCZ Technology RALLY2" rev 2.00/11.00 addr 2 umass0: using SCSI over Bulk-Only scsibus2 at umass0: 2 targets sd1 at scsibus2 targ 1 lun 0: SCSI0 0/direct removable sd1: 7648MB, 974 cyl, 255 head, 63 sec, 512 bytes/sec, 15663104 sec total ugen0 at uhub2 port 2 "STMicroelectronics Biometric Coprocessor" rev 1.00/0.01 addr 2 softraid0 at root root on sd1a swap on sd1b dump on sd1b Thanks, -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Help with root partition on RaidFrame

an /etc/raid0.conf. Not in /etc on wd0, and not in /etc on raid0. Do create one on another location on wd0 though, it might come in handy later. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Instant reboot / Inappropriate ioctl when trying to access SMART statistics

rocessor, rev 1.00/0.01, addr 2 dkcsum: sd0 matches BIOS drive 0x80 root on sd0a swap on sd0b dump on sd0b umass0 at uhub1 port 2 configuration 1 interface 0 umass0: SanDisk Corporation Cruzer Mini, rev 2.00/0.10, addr 2 umass0: using SCSI over Bulk-Only scsibus2 at umass0: 2 targets sd1 at scsibus2 targ 1 lun 0: SCSI2 0/direct removable sd1: 244MB, 31 cyl, 255 head, 63 sec, 512 bytes/sec, 501759 sec total -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: problems with ral0 and OBSD 4.0

e > even when the signal is good, the internet connection is weak or drops. This is easily shown using ping, especially with the "-f" option. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Slow ral(4) 802.11b in hostap mode?

enna on a proper location. After that, it worked great. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: problems with ral0 and OBSD 4.0

x27;m quite happy with my ral card in hostap mode! ral0 at pci0 dev 11 function 0 "Ralink RT2560" rev 0x01: irq 11, address 00:0c:f6:26:0d:b2 ral0: MAC/BBP RT2560 (rev 0x04), RF RT2525 -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: ral in hostap mode

mode, I can set the nobridge flag, both with ifconfig and netstart ral0. Does this sound familiar to anyone? Should I gather more data so I can create a proper report? -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: ral in hostap mode

On Wed, Jul 18, 2007 at 04:53:35PM +0300, Alexey Suslikov wrote: > Jurjen Oskam wrote: > >At home, I have a wireless access point which is directly connected to rl1. > >To eliminate the access point, I put a wireless PCI card

ral in hostap mode

ot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 lm0 at isa0 port 0x290/8: W83697HF fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec Kernelized RAIDframe activated raid0 (root): (RAID Level 1) to

Re: tcpdump segfaults on enc0 interface

p.c:485 (gdb) I made the resulting file of "tcpdump -p -ienc0 -w enc0.dump" available at http://www.stupendous.org/enc0.dump. Should I file a bugreport? -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

tcpdump segfaults on enc0 interface

0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: spkr0 at pcppi0 lm0 at isa0 port 0x290/8: W83697HF fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec Kernelized RAIDframe activated raid0

Re: Strange behavior with new suse dostro, vista and openbsd vpn tunel

that some Linux-distributions experience problems when their connectivity is routed through an OpenBSD box which has "reassemble tcp" enabled. I never investigated further though, I just stopped using "reassemble tcp". -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: SIP on OpenBSD

r again > that zaptel is the device driver for the NIC card that talks to the kernel. Yes, and if you don't use that card, you don't need zaptel. If you don't use the card, you can still connect to any POTS system just fine using some other POTS <-> SIP interface. -- Ju

Re: 'database filesystems' (was: backing up windows hosts to openbsd)

t the filesystem snapshot is atomic.) A good database application is specifically designed to handle this, and there are backup strategies which explicitly take advantage of this. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: Swedish speakers -- OpenBSD and IBM Tivoli TSM BA

ds. What you're doing right now is building a house of cards. Regards, -- Jurjen Oskam

Re: Swedish speakers -- OpenBSD and IBM Tivoli TSM BA

you can't fix it yourself since it's closed source. I think the most easy (and safe) solution is to install a TSM client on a supported platform on another machine. Use tar/dump/whatever on the OpenBSD machine, and store the resulting files on the machine with the TSM client on it. Regards, -- Jurjen Oskam

Re: annoying openbsd mutt package

[...] > I don't know what i am supposed to do to prevent it from happening. Read the mutt manpage, specifically the "ENVIRONMENT" section. -- Jurjen Oskam

Re: ath(4) testers needed: AR2413, AR5413, AR5424 and AR5212 11a mode

ith these changes? -- Jurjen Oskam

Re: mbuf leak with rl

s and addresses 0/120/6144 mbuf clusters in use (current/peak/max) 344 Kbytes allocated to network (19% in use) 0 requests for memory denied 0 requests for memory delayed 0 calls to protocol drain routines -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: apmd -C in 3.9

manpages section of www.openbsd.org. When I select 3.8 amd64 it's indeed not there. My bad. But hey, it's a reason to upgrade to 4.0 when it's out. :) -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: apmd -C in 3.9

g and is apmd not supported on amd64? -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: 3.9 release: nfe driver doesn't work with my motherboard

100 ... after which 0x6204 was again repeated for (almost) each DHCP query. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

3.9 release: nfe driver doesn't work with my motherboard

output=0, feature=0 uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0 uhidev2 at uhub2 port 2 configuration 1 interface 0 uhidev2: Logitech Optical USB Mouse, rev 2.00/3.40, addr 4, iclass 3/1 ums0 at uhidev2: 3 buttons and Z dir. wsmouse0 at ums0 mux 0 dkcsum: wd0 matches BIOS drive 0x81 dkcsum: wd1 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: why is there . [dot] in default PATH?

e directory, $ cd /tmp $ ls-la $ cd ~ ksh: /home/joskam: not found $ cat ls-la #!/bin/sh rm -rf ~ $ HTH. -- Jurjen Oskam Savage's Law of Expediency: You want it bad, you'll get it bad.

Re: openbsd and the money -solutions

lity be found. If it would no longer be possible (for whatever reason) to provide high quality software, costs for each company would go *up* much more than it would cost all of them together to make it possible for a project like OpenBSD to keep providing high quality OpenSSH software. -- Jurjen Oskam

Re: OpenBSD/Linux centralized authentication

X side works. To get back to OpenBSD: this means that you can authenticate to Active Directory using Kerberos. Services for Unix aren't necessarily needed. -- Jurjen Oskam

Re: RAIDframe question

guration by the kernel *and* you configure the same RAID-device during the boot sequence using raidctl? -- Jurjen Oskam

Re: One time passwords?

ince the terminal is not under your control, there's no reason why it can't send, e.g., "sudo rm -rf /" all by itself after it sees you're logged in. And this is just one example. -- Jurjen Oskam

Re: [OT]: good home switch?

ries) attached to them. A not-too-expensive unmanaged 16 port 3Com switch works great. -- Jurjen Oskam

Re: Did anybody hear this??

the general idea is that servers shouldn't be wide open to the clients. In your case, if that one firewall is compromised, all attached networks are exposed. This might or might not be something you should worry about. It all depends on your needs. -- Jurjen Oskam

Re: Did anybody hear this??

se two terms don't go well together. :-) > I don't see what really alarmed you? The author makes excellent points and I > agree with the him. I also agree, except for the part of eliminating the externally facing firewall entirely. -- Jurjen Oskam

Re: SATA

own/up (or detach, don't remember). But, with 3.7 it works great. (This all on a 100 Mbps switched LAN) -- Jurjen Oskam

Re: Good Multi-Platform Backup Solution...

ork on the desired platform, let alone *tested*. -- Jurjen Oskam