.Gavin,
You might take a look at Falconer (Canada) airplanes.
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
---Original Message---
From: KR builders and pilots
List-Post: krnet@list.krnet.org
Date: Tuesday, November 04
.Larry,
We are in SC.. Go look at our website listed below. I live in
Lugoff and Dan lives in Lexington
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
---Original Message---
From: KR builders and pilots
List-Post
...Tim,
It might be TOO simple; but might I suggest that you check your horizontal
stab incidence to your wing stubs chordline. If it is over about three
degrees, you have a large problem..
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
..Tim, et al,
What I ment to say was.. You need at least three degrees negative,
or you have a problem. If it is POSITIVE, you have a BIG problem...
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
---Original
enairs and others.
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
---Original Message---
From: KR builders and pilots
List-Post: krnet@list.krnet.org
Date: Wednesday, October 15, 2003 21:37:01
To: kr...@mylist.net
Subject: Re: KR>Piano hinge
.have just rejoined the net. I did not see the original post on
rivets; but there are lots of planes flying around with pop rivets holding
them together..Teenie2, Zenair, Sonex; just to name a few. But if you
are talking about pop riveting metal to woodFORGET IT!!!
KRJerry
Mark,
The pop rivets would hold the steel and hinge together quite well, but I
would not count on them holding the assembly to the wooden bulkhead. My
vote is for the SCREWs..!!!
Keep on keepng on,
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR
Hey, while I'm thinking about it , is the antenna coax
50 or 75 ohm, (58 or 59 or will the new RG6 work?)
>>>>>>> Larry,
You will want to use RG58 (50ohm)
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Webs
But one person can pull the
motor mount......
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
. However, you could back-up the
plywood by placing an angle or a flat doubler behind
the plywood to make a sandwich. That way you don't
have the
roll in the back of the store.
Don't get the pre packaged stuffit costs more.
Jim Weir, who built the antennas for Voyager (12 of em) and antenna Guru in
general, uses the Radio Shack stuff and sez he can't tell any diffrence in
performance.
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail:
Brian,
...it may have been ice. I have seen your type of set up setting on the
tarmac at 100 degrees with frost all around the Zenith carb.
Just a guess
KRJerry
Jerry Mahurin
Lugoff, SC
e-mail: krje...@bellsouth.net
Website: http://KR-Builder.org
---Original Message
Navigator Dan may have been lost, but I knew exactly where we were; between
Rough River, KY and Faifield County, SC. We did have to clean out the right
front seat (Navigator(?) Dan's) when we landed...
A GOOD time was had by all though!!
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bells
Dan'l
You got the wrong mag article
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builder.org
---Original Message---
From: KR builders and pilots
List-Post: krnet@list.krnet.org
Date: Friday, June 06, 2003 05:35:15 PM
To: kr...@mylist.net
Subject: KR>Dual
.OOOPs. didn't mean to send it to the list.
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builder.org
---Original Message---
From: KR builders and pilots
List-Post: krnet@list.krnet.org
Date: Friday, June 06, 2003 06:00:34 PM
To: kr...@mylist.net
Subje
Thanx Mark,
We finally received a V/C compass from Aircraft Spruce after a three month
back order. We looked it over and sent it back
Let's just say that it did not meet our expectations.
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builder.org
---O
.the Wannabee is a standard KR2 with Diehl wingskinned wings
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builder.org
---Original Message---
From: KR builders and pilots
List-Post: krnet@list.krnet.org
Date: Thursday, May 01, 2003 09:06:00 AM
To: KR bu
Netters.
Have any of you guys looked at drawing a vacum from your exhaust.?
After the Wannabee gets into the air we are going to look into it again. We
have both considered it before on other planes..
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builde
uctDisplay?prrfnbr=1783&prmenbr=361 for $31+
shippingJeg's has alot of really cool race car stuff that has application
for aircraft use (like Russell hose and fittings).
KRJerry wrote:Netters.
Have any of you guys looked at drawing a vacum from your exhaust.?
After the Wan
even at that, it takes a pretty big battery (and alternator) to pull
that inverter. Looks like weight and CG considerations have gone
out the window.
N64KR
Jerry Mahurin
Lugoff, SC
krje...@bellsouth.net
http://kr-builder.org
---Original Message---
From: KR buil
sorry. Did not intend to sound so crass. I have just been watching
grams and ounces of weight in pursuit of performance. But 47# is more than
one of the Wannabee's wings weigh. I guess if you want it all and you
are willing to pay the penalty that is your choice.
N64KR
Jerry Mah
20 matches
Mail list logo
