I had Jet Hot coat the exhaust system for my Rotax 503. Within just a few
months, small bits of rust appeared throughout the whole surface of the
coating. I know little about the process, but it looked like they didn't do a
good job of prepping (cleaning?) before applying the coating. Given t
I have tried to contact Dave Goodman, but since he sued me and collected, I
have not been able to contact him. I would like to contact him to see how he is
doing.
Jim Morehead
On Wednesday, February 15, 2017 12:05 PM, laser147--- via KRnet
wrote:
Send a note to Jim Morehead. He
Hi Chris;
I did let Gary know that it was all in order and not to worry about it.
Thanks again
Bob
- Original Message -
From: "Chris Gardiner via KRnet"
To: "KRnet"
Cc: "Chris Gardiner"
Sent: Wednesday, February 15, 2017 3:53:10 PM
Subject: Re: KR> spar inspection
Thanks for the update
Thanks for the update, Bob.
I'll call off the hounds.
Cheers
Chris
Sent from my iPad
> On Feb 15, 2017, at 9:45 AM, Robert Russell via KRnet
> wrote:
>
> Hi All :
> So I checked with MD-RA and they simply want to see the project , no mention
> of cutting any holes in the box spars or anythi
Send a note to Jim Morehead. He may have it. kr...@sbcglobal.net
Warning: Don't Use Probiotics Before You See This
Gundry MD
http://thirdpartyoffers.juno.com/TGL3141/58a4b42c8dad1342c4ec6st02vuc
Steve Bennett had the exhaust coated with Jet Hot when he put the engine in my
plane and it's held up everywhere except where the crossover pipes come
together. I keep a coat of hi-temp paint on the small area that's affected.
The "Lifetime Guarantee" the Jet Hot advertises is full of exclusi
Oscar wrote: I agree, in general. Just arguing the numbers though, if the AN
bolt has a tensile strength of 125,000 psi,
Let's look at this at a different direction. I'm bolting on a 220 lbs or so
Corvair engine onto a WOODEN firewall at six point. I don't think I need to
worry about the s
Mark L. wrote-
>In general though, the AN5 bolts that Aircraft Spruce sells are far superior
>to grade 5, if that answers your question.
I agree, in general. Just arguing the numbers though, if the AN bolt has a
tensile strength of 125,000 psi, a quick search of the data for grade 5 fine
th
Stef den Boer wrote:
I am still in a doubt to use the M8.8 or to order the AN5/16 Bolt. I
have found
that a M 8.8 Bolt is a grade 5. So I did a search for the AN Bolt
but
cant Find
no grade information for NAS or AN bolts.
There are a lot of different kinds of AN and NAS bolts...probably e
Does anyone have contact info for Dave Goodman?
He built a Kr that he called Goliath. It had a blue/gray camo paint scheme.
The link in the KRNET seems to be broken.
Thanks,
Jim Litchfield
S.E. Virginia
___
Search the KRnet Archives at https://www.mail
Hi everyone,
I am still in a doubt to use the M8.8 or to order the AN5/16 Bolt. I have found
that a M 8.8 Bolt is a grade 5. So I did a search for the AN Bolt but cant Find
no grade information for NAS or AN bolts.
Some of you know this information?
Thanks Stef
> Op 9 februari 2017 om 0:16 schree
Hi All :
So I checked with MD-RA and they simply want to see the project , no mention of
cutting any holes in the box spars or anything of the sort.
I think this was just a misinformed opinion from an inspector in a casual
conversation.
I have sent all the documents to MD-RA and they will take
12 matches
Mail list logo
