Alera was a lake boat. So, when we brought her out to Seattle we had
to remove the VC-17. The folks as Seaview as well as the Interlux
fellow all warned that the silicon in the VC 17 makes it necessary
to take the hull down to gelcoat. I was also advised that since
there may be some penetra
Good advice from Bob, but this bit is wrong:
"If my memory is correct, you have about two weeks after applying the 2000E
to apply your antifouling paint.After that, you have to sand the
2000E. We applied 2 coats of Micron CSC over the 2000E."
You should put your first coat of antifouling on
- Original Message -
From: "dwight veinot"
To: cnc-list@cnc-list.com
Sent: Saturday, January 12, 2013 6:36:15 AM
Subject: Re: Stus-List Barrier Coating after Soda Blasting
I am not aware of any C&C boats that ever had blistering (osmosis) problems, at
least around here
ailto:cnc-list-boun...@cnc-list.com] On Behalf Of dwight
veinot
Sent: Saturday, January 12, 2013 6:36 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Barrier Coating after Soda Blasting
I am not aware of any C&C boats that ever had blistering (osmosis) problems,
at least around here.ma
Edd,
I soda blasted last spring and used Interprotect 2000E. I used almost six
gallons. Alternating gray and white makes it very easy to show where you've
covered the hull for each coat. I had blisters. Lots of small ones, but
some ended up larger than expected. Several were a couple inches
-list@cnc-list.com
Subject: Re: Stus-List Barrier Coating after Soda Blasting
Did the bottom of my boat six years ago when I purchased it.
We did 2 coats of the high build primer (I think the designation is
Interprotect 3000) followed by 3 coats of the Interprotect 2000. It is a
good product li
Did the bottom of my boat six years ago when I purchased it.
We did 2 coats of the high build primer (I think the designation is
Interprotect 3000) followed by 3 coats of the Interprotect 2000. It is a
good product line.
The key is build thickness. If you don't get enough thickness the epox
Roger that. Interlux also recommends it, and provides timing info.
I put hard paint on, then ablative over that, with a different color.
While I prefer to clean my own hull these days, I've been known to get
lazy and hire a local. Some of these guys think every boat is like his
brother-in-la
Hi Edd,
+1 to what everybody else said. I've used Interlux InterProtect 2000E
too. I like it. As Mike said, there is lots of info on
http://www.yachtpaint.com/can/diy/media-center/technical-bulletin.aspx
Here's a good overview of the process:
http://www.yachtpaint.com/LiteratureCentre/gelcoat
Edd -
I used Interlux 2000E on Stella Blue in 2011, and used 5-1/2 gallons.
It's the thickness, not the number of coats, so go ahead and use a
solvent-resistant roller and brush and lay it on thick. It has a pretty
long pot life, and if you mix up too much at any one time you can put
the can
-List Barrier Coating after Soda Blasting
I was advised to apply one coat of your chosen antifouling (Trinidad hard
antifouling was what I used as the base and have applied Vivid over that
since) before the final coat cures completely, otherwise you will have to
sand to get it to adhere to the
I was advised to apply one coat of your chosen antifouling (Trinidad hard
antifouling was what I used as the base and have applied Vivid over that
since) before the final coat cures completely, otherwise you will have to
sand to get it to adhere to the epoxy.
Tim
Mojito
1984 C&C 35-3
Branford, CT
Hello Edd,
May of 2011, here along the Texas Gulf Coast I too had Finesse , a LF39,
soda blasted and on the recommendation of the boat yard:
1. Used the Interlux primer-cleaner
2. Applied 2 full coats of the 2000E and a 3rd coat over the keel and up the
hull about 1/2 way using a rolle
Edd,
I had Touche' barrier coatedtwice. The first time an idiot did it and
rolled it on. The second time a guy who specialized in bottoms (boat bottoms,
that is) did it and he sprayed it on. My vote goes to spraying it on.
I2000E is a very good product.
Dennis C.
Touche' 35-1 #83
Man
main trim on C&C 115 Koobalibra 59115
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Edd
Schillay
Sent: Friday, January 11, 2013 11:57 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Barrier Coating after Soda Blasting
Mike,
Lt. Kurt,
Mike,
Lt. Kurt, who I've known since third grade, was the best man at my
wedding, and has been racing on my team for years is my Science Officer. He can
calculate, in his head, time-on-time racing handicaps during a race and the
physics of air flow over the sail. In his "real life", he'
Who have you hired for Science Officer?
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Edd
Schillay
Sent: Friday, January 11, 2013 11:48 AM
To: cnc-list@cnc-list.com
Subject: Stus-List Barrier Coating after Soda Blasting
Listers,
I'm gettin
17 matches
Mail list logo
