Stus-List emails (digest version) unreadable

The list digest is almost completely unreadable for me. Is it just me? See below. > On Sep 27, 2020, at 10:36 AM, cnc-list-requ...@cnc-list.com wrote: > >> and every one is greatly appreciated. If you want to support the list - >> use PayPal to send contribution -- https://www.paypal.me/stum

Re: Stus-List 1979 C&C 34: why hangers on thru-deck mast fitting?

Anchovy has no tangs. Rick Bushie 30-1 #1 Sent from my iPhone ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution

Re: Stus-List Anchor locker access

Anchovy has an oval hawse pipe about 3”x2” with a cap adjacent to the stem fitting. No windlass...I wouldn’t think that a windlass would be a factory original install on such a small boat. I do want a windlass, though. Rick Bushie Anchovy, 1971 30-1 Tolchester, MD

Re: Stus-List 35-3 Mast Wedges

I use rubber wedges on my 30-1. I don’t remember where I sourced them but google is your friend. My mast boot is constructed from a tire inner tube and contact cement. Works great. Rick Bushie Anchovy 1971 30-1 ___ Thanks everyone for supporting this

Re: Stus-List Shaft coupler removal

I used a cutting wheel and cut a groove longitudinally down one side being careful not to score the shaft. Then a few surgical strikes in the groove with a cold chisel to slightly spread the coupling. Then it slid right off. About a half an hour minus setup. _

Re: Stus-List Shaft coupler removal

Josh, I had to cut mine off. Luckily, a ready replacement was available from Moyer Marine for my A4. Rick Bushie Anchovy 1971 30-1 Sent from my iPhone ___ Thanks everyone for supporting this list with your contributions. Each and every one is

Re: Stus-List Atomic 4 replacement

remove as much as possible prior to beginning…starter, manifold/carb, alternator, etc. As a fat guy in my 57th year, I had little trouble moving the stripped motor around by hand. Good luck, Rick Bushie Anchovy, 1971 30-1 Tolchester, MD ___ Thanks

Re: Stus-List C&C41 Centerboard models for sale

Richard, Vamp https://www.yachtworld.com/boats/1985/c-c-41-center-board-3150023/ Respite https://www.facebook.com/marketplace/item/470979403728539/?surface=product_details

Re: Stus-List C&C41 Centerboard models for sale

Respite is supposedly in Annapolis. She is actually listed on FaceBook Marketplace for a charity fundraiser. Vamp is in Northeast MD listed on Yacht World. They are both 1985 41’, listed for about $50,000. I appreciate the offer Andrew, but they are both in my general area. It’s just a weird

Stus-List C&C41 Centerboard models for sale

Anyone know anything about Vamp or Respite? These are a pair of 41’ Centerboards for sale here on the Chesapeake. ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support

Re: Stus-List Any Mid-Atlantic rendezvous planned

Anchovy is in for the weekend. > On Aug 19, 2019, at 1:37 PM, cnc-list-requ...@cnc-list.com wrote: > > Re: Any Mid-Atlantic rendezvous > planned ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly

Re: Stus-List rick bushie shared ?Keel Bolt Torquing? with you

Does anyone know how to share photos from google photos without it looking like a crappy spam email? ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - us

Stus-List rick bushie shared “Keel Bolt Torquing” with you

Google Photos rick bushie: I had a keel torquing party this weekend. Used a 250lbft torque wrench with a 4x torque multiplier. Trying to link pics from google photos View photos here: https://photos.google.com/share/AF1QipPhzTqlcILVWVJQkqieUTyUdsECZKqlYPJJs_-QBzTZD5g5RUNgOHWvDbDR808Ejg

Re: Stus-List Stair Treads and companion way finishes

I use polyurethane for all interior brightwork. It cures harder. The name brand polyurethanes don’t have UV protection, but we are talking about cabin use here. I refinished Anchovy’s companionway ladder with big box store poly two seasons ago and I see no signs of wear. Rick Bushie Anchovy

Re: Stus-List Saturday morning reading - Wikipedia Article

aft that the chainplates bolt > to…bulletproof. I’ve seen only one other 30-1 that has this upgrade. She is > indeed stiff! I’ve never had to reef. Good thing too, ‘cause once she gets > the bit in her teeth, there’s no leaving the tiller! …and thanx Ken for the great article. Rick Bush

Re: Stus-List Saturday morning reading - Wikipedia Article - Robert W. Ball

improve balance. I’m beginning to doubt Anchovy’s pedigree. I need a hug. Rick Bushie Anchovy, 1971 30-1 Tolchester, MD > On Dec 15, 2018, at 12:00 PM, cnc-list-requ...@cnc-list.com wrote: > ___ Thanks everyone for supporting this list wit

Stus-List digest ejection!?!

For the last few days I’ve been receiving individual messages instead of the digest. Is this possibly a result of forgetting to change out a subject line? I did apologize as soon as I realized what I had done. I’ll apologize again if that’ll help! _

Re: Stus-List Sail plan and heavy weather.

Sorry about the previous post with the wrong subject. As soon as it swshed, I knew I was a jerk. > On Oct 31, 2018, at 12:00 PM, cnc-list-requ...@cnc-list.com wrote: > > Re: Stus-List Sail plan and heavy weather. ___ Thanks everyone for supportin

Re: Stus-List CnC-List Digest, Vol 153, Issue 162

I’ve never put a reef in. 20 knots sustained. Weather helm was a bear though. Sent from my iPhone > On Oct 31, 2018, at 10:47 AM, cnc-list-requ...@cnc-list.com wrote: > > Stus-List Sail plan and heavy weather. ___ Thanks everyone for supporting this

Re: Stus-List C&C 30

The I.D. plate on Anchovy reads as follows: 30 1 71 No zeros, no month. Rick Bushie Anchovy, 30-1 hull 1 Tolchester, MD ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you

Re: Stus-List C&C 30 MKI Prop Strut

. I cut a hole through the bottom of the boat and glassed it in at the proper angle. Worked great. Rick Bushie Anchovy, 1971 30-1, Hull 1 Tolchester, MD ___ The bills have started coming in for the year 2018 and have gone up again. October will be

Re: Stus-List Anyone headed out?

I'll be on Anchovy starting Wednesday noon through the weekend with no agenda as of yet. Rick Bushie Anchovy '71 30-1 Tolchester ___ This list is supported by the generous donations of our members. If you wish to make a contribution to

Re: Stus-List V Berth Holding Tank

ce but not epoxied so that I can pull them again if needed. I also removed the overboard through-hull and glassed it in. I really like having a 30-35 gallon holding tank. Rick Bushie Anchovy, '71 30-1 Tolchester, MD ___ This list is supported

Re: Stus-List Removing 30-1 Exterior Handrails

Randy, I’m sitting on Anchovy right now, and you’ve described the locations of all the screws. I’ve pulled the outside grab rails in the past and there were no more fasteners on Anchovy than you’ve identified. Possibly some 5200 was used the last time they were installed? Rick Bushie

Re: Stus-List Owners' Database

I have no idea Randy! Maybe I’ve been mistaken about what the data on Anchovy’s ID plate means. Rick Bushie Anchovy, 1971 30-1 Tolchester, MD ___ This list is supported by the generous donations of our members. If you like what we do, please help us

Re: Stus-List C&C 30mkI numbering

Anchovy doesn't have a HIN. Just a small C&C plate on the transom inside the cockpit with 30-1 on one end and 1971N on the opposite end. Rick Bushie 1971 30-1 Anchovy Tolchester, MD ___ This list is supported by the generous donations of ou

Re: Stus-List Stupid Reefing Mistake

Reef? What's a reef? Rick Bushie Anchovy, 1971 30-1, hull #1 Tolchester, Md. Sent from my iPhone ___ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating

Re: Stus-List 2016 C&C Northeast Rendezvous -- Mystic Seaport, CT -- Sept 10-12, 2016

o Cohansey Cove for a break. 12 - 14 hour trips are no problem as long as I'm not crashing into 6 foot square chop not too uncommon on the DelBay with opposing forces. But, you're absolutely right about the canal route being the way to go. Rick Bushie Anchovy, 1971,

Re: Stus-List 2016 C&C Northeast Rendezvous -- Mystic Seaport, CT -- Sept 10-12, 2016

and 210 miles to Mystic around Montauk. Rick Bushie Anchovy, 1971, 30-1 Tolchester, MD ___ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!

Re: Stus-List 2016 C&C Northeast Rendezvous -- Mystic Seaport, CT -- Sept 10-12, 2016

go on sale on Defender. With my winning personality, that might be the only way I could get one. As it stands right now, I'm on vacation from 9/2 - 9/19. Plenty of time. Rick Bushie Anchovy, 1971, 30-1 Tolchester, MD ___ This list is supported

Re: Stus-List 2016 C&C Northeast Rendezvous -- Mystic Seaport, CT -- Sept 10-12, 2016

My “man-cation" is during that timeframe. I’m trying to decide if I want to single hand each way from the Chesapeake. I charted it out last night at around 325 miles if I take the narrows into LIS. Rick Bushie 1971 30-1 Tolchester, MD ___ This

Re: Stus-List 30-1 PHRF

174 base. 6sec for roller furling above deck and 9sec for three blade fixed prop. 189 adjusted phrf spin/non-spin. Ches Bay. Rick Bushie Anchovy, #1 Tolchester, MD Sent from my iPhone ___ This list is supported by the generous donations of our

Re: Stus-List Soft thumping/banging when in gear at low-rpm?

Anchovy had the same symptoms three years ago...broken strut. Rick Bushie Anchovy, 1971 30-1 Tolchester, MD ___ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All

Re: Stus-List Mast boot

Anchovy's five year old boot is cut from an inner tube from Tractor Supply. The seam is sealed with contact cement and the sail track filled with silicone. Not a drop of leakage. Rick Bushie Sent from my iPhone ___ This list is supported b

Re: Stus-List 30-1 Mainsail Foot Length

Anchovy's boom reaches back to within four inches of the backstay. The mails'l clew falls about two feet short of the end of the boom. This winter, I actually raised her boom up a foot to create headroom in the cockpit. Luckily the mAins'l luff was a foot short to begin wit

Re: Stus-List 30-1 Displacement

Randy, I've never weighed Anchovy. I do know that I can't carry her very far when I put her on my back. Seriously though, I think the difference in numbers is found in the distinction between weight and displacement. Rick Bushie Anchovy, 1971 30-1 Tolchester, Md Sent from

Re: Stus-List Gate Valves

I bit the bullet and replaced all my through hulls and replaced the gate valves with proper seacocks. The forty year old (at the time) plumbing just didn't inspire confidence. Rick Bushie Anchovy, 1971, 30-1 Tolchester, MD ___ This list is supp

Re: Stus-List Frolic II 36' cb will be for sale soon

The offer to swap boats a coupla years ago still stands. Anchovy for Frolic. Sent from my iPhone ___ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributi

Re: Stus-List Soft shackle

ution dictates that I make a new batch this winter. Rick Bushie Anchovy Sent from my iPhone ___ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinf

Re: Stus-List repacking toe rails

I tightened all toe rail bolts during Christmas vacation. None of the bolts spun as I tightened from below. This seems to have eliminated all water ingress from topsides. I would try that before I tore into the deck/hull joint. Rick Bushie Anchovy Sent from my iPhone

Re: Stus-List 30-1 Vang Refit?

, the wire topping lift. I wish I had a nickel for every time the lift wrapped itself around the backstay during a jibe and needed to be manually unfouled. She is sans a vang at present and the twist in the mains'l is impossible to get rid of with the end boom sheeting. Rick Bushie Anc

Re: Stus-List Early 30-1 Interior Doors

Anchovy has a hinged bi-fold door between the v-berth and the head. The hinges are on the hanging locker side and is held either open or closed with a simple hook and eye assembly. As far as displacement, I really couldn't say as I've never weighed her. Rick Bushie Anchovy, 1971 30

Re: Stus-List Replacing through hulls on a 30 MK1

Anchovy got all new through hull fittings and proper seacocks four years ago. I bought everything, including flush fitting through hulls from Deep Blue Yacht Supply. I used a small diamond cutting wheel on my Rotozip to cut out the old fittings. Rick Bushie Anchovy, 30-1, Hull 1 Worton, MD

Re: Stus-List tightening the tiller

the tiller and the cockpit deck. Hope this helps Rick Bushie Anchovy, C&C 30-1, Hull #1 Worton Creek, MD ___ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-li

Re: Stus-List Stove

sits nicely across the two burners on top for breakfast goodies. What's not to love! I highly recommend non press alcohol. Rick Bushie Anchovy, 1971 30-1 Worton Creek, MD ___ Email address: CnC-List@cnc-list.com To change your list preferences,

Re: Stus-List teak grab rail help 35 MK I

Joe, I know the 30-1 isn't the same boat but Anchovy's grab rails are wood screwed from inside the cabin THROUGH the cabin grab rails. Rick Bushie Anchovy 30-1 Worton Creek, MD ___ This List is provided by the C&C Photo Album Email add

Re: Stus-List Sail donation

Walt, Feel free to drop that spin over on "D" dock in Anchovy's cockpit! Rick Bushie Sent from my iPhone ___ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, incl

Re: Stus-List Mooring or Slip for 2014 season

y but I'd think that proximity to Baltimore would drive up prices. Rick Bushie Anchovy, 1971 30-1 Worton Creek, MD ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Refrigeration for a C&C 30-2

;ve not had any problems with power management this year. Rick Bushie Anchovy 1971 30-1, Hull 1 Worton Creek, MD Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Broken strut

esign. Rick Bushie Anchovy 1971 30-1 Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Stus-List C&C History now too much boat

Hey Tom, Let me know when you're ready to trade! Rick Bushie Anchovy, 1971 30-1 Worton Creek, MD ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Stus-List Prettiest Girl

30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1, 30-1! Rick Bushie Anchovy, Worton Creek, MD Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List replacing steaming old light

Paul, The mounting pad on my 30-1 is welded on the front of the mast. Rick Anchovy ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List water tank capacity 36-foot

I can't say I've increased capacity on Anchovy. I converted the 35 gallon tank under the v-berth to a holding tank as when I bought her she had a two gallon gas can for that purpose. Then, to replace the capacity i installed bladders on either side of the v-berth. I carry 50 gallons now. Rick

Re: Stus-List self-cleaning shaft

Barnacle cuts are nasty! I have one in my foot from cleaning bottom on day one of man-cation. As an aside, I'm in Selby Bay on the South River on day four of Man-cation 2013. Rick Sent from my iPhone ___ This List is provided by the C&C Photo Album htt

Re: Stus-List self-cleaning shaft

Joe, How much does a bottom cleaning run? Rick Anchovy Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List BOR

No Joe! I just wanna crew! Rick Anchovy Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List BOR

Me too!, Me too! I wanna go! Rick Bushie Anchovy ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Stus-List ReCRYC race

Three as of last nite that I know of. But a fourth skippered by a joe Lombardo has entered gob class. Not sure if he's a c&c though. Rick Anchovy Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@

Re: Stus-List C&C 30 MK1 prop location

Ron, As Gary said. Anchovy is hull 1 built in 1971. Centerline 7/8" shaft hanging of of an Atomic 4. Question for you. If your prop and shaft are offset, is your engine mounted crooked or just off center? Rick Bushie Anchovy ___ This Li

Re: Stus-List C&C 30 MK1 backing help

Anchovy's prop is on centerline. Rick Bushie Anchovy Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Corsica River Rendezvous and Race Crew Needed (TOM VINCENT)

11 year old boy who doesn't listen and the other is a 65 year old man who doesn't know how to sail. Your pick. Rick Bushie Anchovy ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Stus-List Chesapeake Rendezvous - Weekend with Joe

Just got my phrf cert in my email. 186! More generous than I expected. I guessed 180 on my race app. they gave me 6 sec for furler and 6 sec for three blade solid prop. Rick Bushie Anchovy ___ This List is provided by the C&C Photo Album

Stus-List Chesapeake Rendezvous - Weekend with Joe a

Yeah, fun for all the big boats! Just don't put me in the middle of the raft-up...and save me some chicken! Rick Anchovy ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Chesapeake Rendezvous - Weekend with Joe at CRYC

Rick Brass, I'm in for the Light Race. So far, plenty of room at the start line! ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Stus-List Chesapeake Rendezvous - Weekend with Joe at CRYC

to entering the Balto Light Race in the next day or two. Rick Bushie Anchovy ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Bigger Boat Question

I have a 30 I'll trade for a LF38 even up! Anyone? Rick Bushie Anchovy MD ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Chesapeake Rendezvous - Weekend with Joe at CRYC 7-27

Joe, I have applied for a phrf for Anchovy and gotten approval from cbyra to run with sail #1. Plan to enter light race and join the festivities. Hope we don't embarrass ourselves. As of now, looks like our entire crew will include myself and my 11 year old son. Rick Bushie Anchovy,

Re: Stus-List C&C 30 Spreader to deck measurement?

o what I'm doing wrong. Rick Bushie Anchovy 30-1 MD Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List C&C 30 Spreader to deck measurement?

jacks in their current configuration. Food for thought. Rick Bushie Anchovy, 30-1, Hull #1 Worton Creek, MD ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List Chesapeake Rendezvous - Weekend with Joe at CRYC 7-27

Hey Joe, Anchovy is interested in participating in the Balto Light race and subsequent get together. We don't, however, have a phrf rating or really know how to get one or if we really want to get one. We don't race (mostly because the boat's faster than her skipper). Suggestion

Stus-List 30-1 reefing system

Here (diagram 2) is a link to what Anchovy runs. That winch on your boom is for taking up on your reefs and or what appears to be your semi-internal outhaul. Hope this is helpful. http://www.ronstan.com/marine/reefing_systems.asp Rick Bushie s/v Anchovy Sent from my

Re: Stus-List factory reefing arrangement C&C 30MK 1

Anchovy (hull#1) has a roller boom. I put in two line slab reefing for both reefs led back to the cockpit. This arrangement works very well but I'm switching out the double braid I originally used with dyneema or spectra to cut down on the effort required to overcome friction. Rick Bushi

Re: Stus-List Possible C&C 30 purchase

l luff is about 10 inches short) but couldn't get the machine screws out. BTW, my yard removes the backstay on almost all the boats it hauls, and with the 30 its no problem at all...the darn mast is a tree trunk and as stated is keel stepped 6 feet below the partners. Rick Bushie s/v Anchovy,

Re: Stus-List StRe: Possible C&C 30 purchase

aced since then. George Hinterholler possibly owned Anchovy? Cool! Gary, gonna start charging royalties! You hang in St. Mikes...you must be rich! Rick Bushie s/v Anchovy, 1971 30-1, Hull 1 Worton Creek, MD Sent from my iPhone ___ This List is provided

Re: Stus-List Holding Tank for C&C 35 Mk I

type hoses and installed a carbon filter in the vent line. Someday, I'll replace the deck fitting so that it reads "waste" instead of "water"! Hope that helps. Rick Bushie s/v Anchovy, 1971 30-1, Hull #1 Worton Creek, MD ___

Re: Stus-List Topping Lift 33-1

do the job. Rick Bushie s/v Anchovy, 1971 30-1, hull 1 Wonton Creek, MD Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

cnc-list@cnc-list.com

This is why I like the hard plastic sole in Anchovy. I replaced the little bilge coverwith new 1/4" marine ply coated with epoxy and 15 coats of varathane. Now I just sweep the pan and scrub with soap and water once a season. Rick Bushie Anchovy 1971 30-1, Hull 1 Worton Creek, MD

Re: Stus-List Early 30-1

Just re-read your message... I have the scimitar shaped rudder as well. Sorry! Sent from my iPhone ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com

Re: Stus-List early 30-1

with slab reeding and a three part out haul adjusted at the boom end. Rick Bushie s/v Anchovy 1971 30-1 Hull 1 Worton Creek, MD Sent from my iPhone On Jan 10, 2013, at 3:47 PM, cnc-list-requ...@cnc-list.com wrote: > Send CnC-List mailing list submissions to >cnc-list@cnc-list.com &

Re: Stus-List Stus-Trip Planning

Joe, Baltimore Light is the same thing as Seven Foot Knoll light, right? I have a four days off that weekend. Rick Bushie s/v Anchovy 1971 30-1 Hull 1 Worton, MD > -- > > Message: 10 > Date: Thu, 10 Jan 2013 14:16:37 -0500 > From: "Della Bar

Re: Stus-List was: trip planning, now:dummies who forget to edit subject line!

That would be me! Sorry! On Thu, Jan 10, 2013 at 1:37 PM, rick bushie wrote: > In 2008 I bought my first boat ever... a C-22 off of eBay for $400. > Anchovy will be joining the Catalina 22 fleet in July for their East Coast > National Cruise this summer as usual. This year we&

Re: Stus-List CnC-List Digest, Vol 84, Issue 30

ed in around Labor Day for my second annual DelMarVa circumnavigation. The balance of the summer will be filled in with day and weekend trips around the upper Chesapeake Bay. Putting in Refrigeration and a propane stove this winter...gotta log a lot of anchor time to recoup my boat bucks! Rick Bus

Re: Stus-List Sailboat show rendezvous?

We will be at the show all day Monday... ___ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com