I had a Rule (I think) traditional style flappy float switch, that failed after
about a year in an always-on position, fortunately it was suitably fused so
blew that before the wire caught fire although it did also manage to destroy
the pump. Switched to an electronic switch (which IIRC was a Jo
When I dropped the rudder on our 34R, I had to dig a hole to allow for the long
shaft. I dug a two foot deep hole and setup a long lever (2 x 8) and fulcrum
(sawhorse or a short ladder that is slightly higher than the bottom of the
rudder) to accept the weight of the rudder before removing the
When we rebuilt our rudder several years ago, it did take removal of
quadrant, doughnut nut and some jiggling to remove. Had 2 strong folks
helping which was a real plus as the rudder was water logged and heavy. Much
easier putting the rebuilt dry and much lighter rudder back in. Good advice
to b
IIRC, on my C&C 39 I removed the collar, (first block the bottom of the
rudder)
Loosened the quadrant, , and drove a screwdriver or pry bar into the slot on
the back, to hold it open a little bit so it would slip.
Then I had to dig a hole and jack the back of the cradle up some.
Measure how
Whoa...the 40s rudder was a 4 man job.
Sent from my Android. Please forgive typos. Thank you.
From: CnC-List on behalf of Joe Della Barba via
CnC-List
Sent: Saturday, March 14, 2020 6:31:03 PM
To: cnc-list@cnc-list.com
Cc: Joe Della Barba
Subject: Re: Stus-Li
On the MK I, once you get the collar and the quadrant off, it should be
free. I had to wiggle mine and pull it to get it out. It was
surprisingly light once I got it loose, no issue carrying it around.
Joe
Coquina C&C 35 MK I
On 3/14/2020 3:18 PM, Garry Cross via CnC-List wrote:
Hi all, I sta
We just cancelled the Coomorode’s Ball and are looking at opening day at the
beginning of May.
Tom Buscaglia
S/V Alera
1990 C&C 37+/40
Vashon WA
P 206.463.9200
C 305.409.3660
> On Mar 14, 2020, at 8:51 AM, cnc-list-requ...@cnc-list.com wrote:
>
> BERGEN)
>
>
> --
Everything at our club is cancelled until May 2nd. Oh wait we shut down just
after haul-out in Oct 😜
Mike
> On Mar 14, 2020, at 2:22 PM, Shawn Wright via CnC-List
> wrote:
>
>
> Our club just closed the bar and clubhouse, and Sunday races are cancelled
> for the next 3 weekends. Other loc
What year make and model?
Loosening quadrant my not be enough. I removed mine. You may want to bridle
the rudder somehow in case it decides to break loose.
David F. Risch
(401) 419-4650
From: CnC-List On Behalf Of Garry Cross via
CnC-List
Sent: Saturday, March 14, 2020 3:19 PM
To: cnc-lis
Equalization is not a problem as long as you water the batteries before and
more importantly AFTER each cycle. There is a point of diminishing returns
regarding equalizing but I'm not sure there is a point of damage beyond
boiling dry.
Josh Muckley
S/V Sea Hawk
1989 C&C 37+
Solomons, MD
On Fri,
Hi all, I started the process of removing my rudder. I have loosened the
quadrant and cables attached to it and removed the bearing on the top of
the rudder. Should it now just drop out? What else needs to be done?.
Thanks all.
___
Thanks everyone for s
The short red wire connects power from one fuse to the other instead of
having two longer leads from the power source. Definitely replace the fuse
holders. I recommend replacing the fuse holders with fuse holders from an
automotive parts store, if you can mount them close to the power source..
They
In my opinion, bilge pumps should wired to a house battery. A dedicated wire
should run from the battery or its connection on the back of the battery switch
to a purpose made bilge pump “on-off-auto” switch with self contained fuse.
Dennis C.
Sent from my iPhone
> On Mar 14, 2020, at 11:35 A
Our club just closed the bar and clubhouse, and Sunday races are cancelled
for the next 3 weekends. Other local clubs are revoking reciprocals also,
but I haven't heard about regattas being cancelled yet. I suspect they will
be.
--
Shawn Wright
shawngwri...@gmail.com
S/V Callisto, 1974 C&C 35
http
Look at the Ultra Safety Systems bilge switch.
https://www.ultratef-gel.com/ultra-pump-switches/
It is contained in a tube so nothing will hold it in the on position. Extremely
reliable switch.
Dennis C.
Sent from my iPhone
> On Mar 14, 2020, at 10:24 AM, Charlie Nelson via CnC-List
> wr
I finally managed to reduce the files size sufficiently.
On Mon, Mar 9, 2020, 23:42 David Knecht via CnC-List
wrote:
> My main breaker has a rotary switch (now replaced with a Blue Seas
> selector switch) and four fuses running from positive power to the main
> electrical panel. Most of the fus
Hey edd, hope all is well with you. My local club, lake Townsend yacht club,
sail our one design boats on a city reservoir. The city of Greensboro has
cancelled all events at the lake due to the virus. So I race today is
cancelled. Jim Schwartz SEA YA!38 landfall (currently for sale)Washington
Put a fuse, close to the charger, between the charging outputs and the
batteries. The charger manual should tell you what size fuse to use. My
Water Witch works, even when it's dirty.
Alan Bergen
35 Mk III Thirsty
Rose City YC
Portland, OR
On Sat, Mar 14, 2020 at 9:36 AM Charlie Nelson via CnC-Li
My charger outputs go only to the batteries, which power the relay panel
switches/breakers, one of which is the bilge pump. Should I use a fuse on the
battery positive terminal in addition to the circuit breakers on the breaker
panel?
(I don't recall whether the bilge pump circuit breaker was 't
After two float switch failures, I switched to an electronic switch. No
more failures. Besides having a circuit breaker on the AC side of your
charger, you should have fuses in the DC side,
Alan Bergen
35 Mk III Thirsty
Rose City YC
Portland, OR
On Sat, Mar 14, 2020 at 8:24 AM Charlie Nelson via
We have a regatta coming up, a week from today. We're going ahead with the
races, but cancelled the after race social.
Alan Bergen
35 Mk III Thirsty
Rose City YC
Portland, OR
On Sat, Mar 14, 2020 at 5:48 AM Edd Schillay via CnC-List <
cnc-list@cnc-list.com> wrote:
> Listers,
>
> I’m curious to k
Thanks all for your replies--I might need to tighten the packing gland or
replace the packing material.
My fear about leaving the auto bilge pump on is a result of a failed float
switch many moons ago:
I was away from the boat between weekends (at least) and it may have been
several weeks and le
Bruce,
Designed Aircraft hydraulic electric motor pumps, We used 20 drops per
CC, which is consistent with 1.14 gal per day. The Phosphate Ester
fluid used has a specific gravity of .975 so it is a little thinner than
water but close enough. That said, if you a dripping at 1 drop per
secon
Per the web (?), a drop of water is 'defined' to be 0.05 mL. In this case, a
drop/second x 86400 seconds/day = 4320 mL or 4.32 L.
For my case (~ a drop/18 seconds), this is about 0.24 L/day--which is probably
consistent with my bilge content when left without the pump working.
Since I had the
Edd
Our local sailing club will hold their 41st annual St. Patrick's Regatta on
21/22 March 2020. So far, they have not cancelled. The thought is that
since the competitors will be on the water with little to no (hopefully)
contact between crews or boats during the regatta we should be OK. I doubt
Listers,
I’m curious to know what your local clubs are doing in response to the COVID-19
pandemic. We have a regatta scheduled for April 4 and we are already discussing
cancelling the skippers meeting and post-race festivities - perhaps cancelling
the event altogether.
What are you seeing in
Hi Pierre,I was interested in your comment and went to verify it, and found a
huge disparity in results, everything from the 1.14 you mention to as much as
8 gallons per day, and some of those coming from seemingly reputable websites.
Comments anyone?Sent from Samsung tablet.
Original
Just for reference, 1 drop per second is 1.14 us gallon per day.
Regards,
Pierre Tremblay
Avalanche #54988
C&C38-3 WK, hull #76
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If y
28 matches
Mail list logo
