What version of VMS? Check the startup file (Systartup_v5.com or
Systartup_vms.com) and see what's going on with the system before you
change anything IYAM.
Using the editor you can comment out networking lines if you want to
disable the DECNET commands. See if Multinet is installed, that's an e
> On 2 May 2019, at 23:16, Carlos E Murillo-Sanchez via cctalk
> wrote:
>
> Hello;
>
> In my quest to try to see what the problem is with my vs/60, I want to
> convert it into a networked stand-alone machine, i.e. not use clustering at
> all. What is the easiest way to do this? I still wan
Hello;
In my quest to try to see what the problem is with my vs/60, I want to
convert it into a networked stand-alone machine, i.e. not use clustering
at all. What is the easiest way to do this? I still want it to do
DECnet and TCPIP.
Carlos.
> On May 2, 2019, at 10:49 AM, Ethan Dicks wrote:
>
> On Thu, May 2, 2019 at 8:13 AM Paul Koning wrote:
>>> On May 1, 2019, at 10:58 PM, Ethan Dicks wrote:
>>> I think those were still true for V3.X. I know we had a problem back
>>> then with our backups where someone elevated the priority
> From: Mister PDP
> reading through the "DLV11-E and DLV11-F asynchronous line interface
> user's manual", the diagrams of the DLV11-E and F do not line up my
> module.
Oh, must be a later board rev, one that's not covered in EK-DLV11-OP-001.
(I should have compared your pic with
Well, it defiantly is a M8017 (M8017-AA to be exact), not a M7940.
https://ibb.co/rQk55FC
>From what I read, the M8017-AA refers to the DLV11-E/EC, but reading
through the "DLV11-E and DLV11-F
asynchronous line interface user's manual", the diagrams of the DLV11-E and
F do not line up my module.
> From: Mister PDP
> I have this DEC M8017-AA / DLV11 module that I am trying to configure
> ... the only manuals or resources I can seem to scrounge up are for the
> DLV11-E, DLV11-F, and DLV11-J.
> If anybody knows what the jumper settings are, or where I can find
> them
On Thu, May 2, 2019 at 8:13 AM Paul Koning wrote:
> > On May 1, 2019, at 10:58 PM, Ethan Dicks wrote:
> > I think those were still true for V3.X. I know we had a problem back
> > then with our backups where someone elevated the priority of the Tape
> > ACP over the Disk ACP (because it was faste
Hello,
I have this DEC M8017-AA / DLV11 module that I am trying to configure to
act as a console. I have been trying to find a manual to tell me what
jumpers go where, but the only manuals or resources I can seem to scrounge
up are for the DLV11-E, DLV11-F, and DLV11-J.
If anybody knows what the
> On May 1, 2019, at 10:58 PM, Ethan Dicks wrote:
>
> On Wed, May 1, 2019 at 7:42 PM Paul Koning via cctalk
> wrote:
>> ...
>> 9.3 names back then, I'm pretty sure. File system still in an ACP (separate
>> process)? DECnet Phase II ???
>
> I think those were still true for V3.X. I know w
10 matches
Mail list logo
