Hello,
When I type "alsactl restore", it does not load the driver state.
Steps to reproduce:
1. Open a first terminal dedicated to alsa-mixer
2. Open a second terminal where you will type the following commands
3. In the first terminal, press F4, set the audio volume for capture to 40
4. In the
On Sun, 4 Feb 2018 13:22:43 +0100, Clemens Ladisch via Alsa-user wrote:
>Nikos Chantziaras wrote:
>> How do I assign numbers?
>
>With a line
>
> options snd slots=snd-virtuoso,snd-usb-audio
>
>in some .conf file in /etc/modprobe.d/.
FWIW "some .conf file" means you could name it as you want, a
Nikos Chantziaras wrote:
> How do I assign numbers?
With a line
options snd slots=snd-virtuoso,snd-usb-audio
in some .conf file in /etc/modprobe.d/.
Regards,
Clemens
--
Check out the vibrant tech community on one of
On 29/01/18 14:25, Clemens Ladisch via Alsa-user wrote:
Nikos Chantziaras wrote:
alsactl sometimes fails to restore the mixer settings at system boot. Failure
rate is about 50/50.
systemd-udevd[151]: Process '/usr/sbin/alsactl restore 1' failed with exit code
99.
systemd-udevd[149]: Process '
Nikos Chantziaras wrote:
> alsactl sometimes fails to restore the mixer settings at system boot. Failure
> rate is about 50/50.
>
> systemd-udevd[151]: Process '/usr/sbin/alsactl restore 1' failed with exit
> code 99.
> systemd-udevd[149]: Process '/usr/sbin/alsactl restore 0' failed with exit
>
Hello.
On a Gentoo systemd system, with alsa-restore.service enabled, alsactl
sometimes fails to restore the mixer settings at system boot. Failure
rate is about 50/50. Half the time it restores correctly, half the time
it does nothing.
However, even when it fails, systemd thinks it succeede
Hello,
I installed alsa-lib and alsa-utils. Then I ran 'alsactl store' to save
the volume level. This is how I got /etc/asound.state. Then I ran
'alsactl restore' and got this message:
Unknown hardware: "YMF724F" "SigmaTel STAC9700,83,84" "AC97a:83847600"
"0x1073" "0x000d"
Hardware is initi
I have been getting
'alsactl restore' failed with error message "Unknown hardware ..."
and
"Saved ALSA mixer settings detected: aumix will not touch mixer ... (warning)"
Running a debug procedure ..
cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.20.
cat /proc/a
Hi,
My bootup msgs include
'alsactl restore' failed with error message "Unknown hardware"
.. and later with
"Saved ALSA mixer sttings detected: aumix will not touch mixer .. (warning)"
"lspci" (as root) gives me
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 730 Host (rev 02)
00:00.1
At startup, settings are obviously restored, but whenever I change
anything in envy24control, these are not stored at shutdowwn.
- kernel 2.6.3
- alsa driver version 1.0.2c (supplied with kernel source)
- alsa utilities etc.: 1.0.2
... and before you ask, this is the important portion of my
/etc
Hi,
On Mon, 17 Nov 2003 23:25:57 +0100 wwp <[EMAIL PROTECTED]> wrote:
> 1/
> since alsa 0.9.8 packages, alsactl always crashes when invocated
> from /etc/init.d/alsasound start or stop (so w/ -f and store/restore command),
> whereas it works well from console after init completion.
>
> It seems
Hi alsa folks,
1/
since alsa 0.9.8 packages, alsactl always crashes when invocated
from /etc/init.d/alsasound start or stop (so w/ -f and store/restore command),
whereas it works well from console after init completion.
It seems to crash from 0.9.8, but probably since 0.9.7 too (OK w/ 0.9.3-0.9.
Hi,
I just backported Debian unstable ALSA packages to my stable
system. Current ALSA version packaged in the unstable branch is 0.9.4.
The script /etc/init.d/alsa includes calling alsactl store on stopping
and alsactl restore on starting, so mixer settings are saved between
sessions. However, th
When I run "alsactl store" I get this message:
ALSA lib conf.c:1156:(parse_def) is not a compound
ALSA lib conf.c:1565:(snd_config_load1) _toplevel_:4:28:Invalid argument
alsactl: conf.c:1226: string_print: Assertion `0' failed.
And sometimes this message:
ALSA lib conf.c:1565:(snd_config_load1)
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
I have an onboard intel 845 chipset using the
snd-intel8x0 alsa driver for sound, everything
works fine except that alsactl hangs on either
a save or restore, except during the initial
boot it when it loads ok. I'm using alsa
0.9.4 and I'm sure I've r
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
I'm having an annoying problem with alsactl, on shutdown
it hangs when trying to save the state of all the mixer
controls. During startup I haven't had a problem, but
if I manually run the alsa startup script, it hangs trying
to restore the state and
At Wed, 12 Feb 2003 12:25:47 +0100 (CET),
Sylvain Petreolle wrote:
>
> [1 ]
> > > But if I hit halt|shutdown| ctr-alt-del, the alsactl service is
> > > reported sucessfull but set all channels to 0 and mute them.
> >
> > please make sure that this alsactl init script is called in the boot
> > se
> > But if I hit halt|shutdown| ctr-alt-del, the alsactl service is
> > reported sucessfull but set all channels to 0 and mute them.
>
> please make sure that this alsactl init script is called in the boot
> sequence. i guess no symlink was created for a certain runlevel.
[syl@snoop syl]$ ls -l
At Wed, 12 Feb 2003 00:12:40 +0100 (CET),
Sylvain Petreolle wrote:
>
> Hasnt got someone any clue about this ?
>
> Using rc7, I have all mixers set to muted and volume at 0.
>
> I have no problem with sound if I set it with alsamixer.
>
> Becoming root and run /etc/init.d/alsactl start|store wh
Hasnt got someone any clue about this ?
=
Sylvain Petreolle
[EMAIL PROTECTED]
Fight against Spam ! http://www.euro.cauce.org/en/index.html
ICQ #170597259
"Don't think you are. Know you are." Morpheus, in "Matrix".
___
Do You Yahoo!? --
Using rc7, I have all mixers set to muted and volume at 0.
I have no problem with sound if I set it with alsamixer.
Becoming root and run /etc/init.d/alsactl start|store when the machine
is up saves correctly the values into /etc/asound.state.
But if I hit halt|shutdown| ctr-alt-del, the alsactl
"alsactl restore 0" gives error and does not restore mixer settings which
have to be changed manually when rebooting. This is painful but doable
since the sound works fine other than for this glitch.
The error is:
boris:~/# alsactl restore 0
alsactl: set_control:960: Cannot write control '3:0:0:
Frank Barknecht wrote:
Everything is always muted when I restart my computer.
I have an /etc/asound.state but I always have to run alsamixer.
Does "alsactl restore" restore the settings? If yes, that you need to
add this somewhere in your startup scripts or maybe into the
module-configuratio
Hi,
Bob Lockie hat gesagt: // Bob Lockie wrote:
> Everything is always muted when I restart my computer.
> I have an /etc/asound.state but I always have to run alsamixer.
Does "alsactl restore" restore the settings? If yes, that you need to
add this somewhere in your startup scripts or maybe into
Everything is always muted when I restart my computer.
I have an /etc/asound.state but I always have to run alsamixer.
From Mozilla and GNU/Linux
---
This sf.net emial is sponsored by: Influence the
hi im using the latest alsa (0.9beta10) it's all ok but i cant store the
config with alsactl, here the shell err:
[root@localhost nerula]# /usr/sbin/alsactl store
/usr/sbin/alsactl: save_state:963: No soundcards found...
why this? i cant understand...i got the card, if i open the mixer the
level
For the last couple of months, both the cvs version as well as the 9.0
beta 8 version will not compile the alsa-utils on my box. I am running a
RH6.2 system with an upgraded kernel 2.4.10. The sound card is a SB512.
Every time I try to compile alsa I get
alsactl.c:1053: `SND_CTL_POWER_D0' undec
27 matches
Mail list logo
