In data giovedì 14 gennaio 2010 00:08:00, Nils Erik Svangård ha scritto:
> ==
> Opening audio decoder: [pcm] Uncompressed PCM audio decoder
> AUDIO: 32000 Hz, 7 ch, s16be, 6272.0 kbit/87.50% (ratio: 784000->896000)
> Selected a
Hi!
I'm trying to get the most out of my surround system.
Now I'm trying to get LPCM pass through directly to my receiver over S/DIF.
I'm not getting it to work. Could it be that it is supposed to be sent
in 190kHz and the M-Audio Delta 1010LT only support up to 96kHz?
This is what mplayer says:
l
2010/1/9 Nils Erik Svangård :
[snip]
> I have some lingering questions:
> -Can I somehow fix so I dont have to use Envy24control to change
> these settings? Can I do it dynamiclly on the fly?
Perhaps the iecset command could help?
It has boolean options for audio mode and professional mode.
But I
Solved it!!! :D
After a couple of hours of trying different combinations of settings I
finally found what was wrong!
For AC3 or DTS pass through in Envy24Control must be set:
-Hardware Settings:Professional:Data-Mode = Non-audio
-Patchbay/Router:S/PDIF OUT (L) = S/PDIF OUT (L)
-Patchbay/Rout
> You can't output more than 2 channels over SPDIF using PCM. To do this you
> have to use a compressed audio stream (Dolby Digital, DTS, etc.)
>
Ah, ok that is good to know! Can the 1010LT card send activity on its
diffrent channels as DTS, Dolby Digital or anything else. Eg. can I
from Ardour pi
> Make sure you have a Dolby or DTS surround file and try to play it with
> mplayer
>
I think I have. I have downloaded some from the net.
If I have activity on 5 channels when watching in Envy24Control is the
PCM-stream that is sent from the card automaticly compressed into DTS
or any other stand
Op Thu, 07 Jan 2010 00:35:08 +0100 schreef Nils Erik Svangård
:
> Hi!
> I'm having trouble getting surround sound working with my M Audio
> Delta 1010LT over S/PDIF.
>
> When I run:
>> speaker-test -Dplug:surround40 -c4 -l1 -twav
>
> It seems that all channels have been mixed into my two front s
Hi!
I'm having trouble getting surround sound working with my M Audio
Delta 1010LT over S/PDIF.
When I run:
> speaker-test -Dplug:surround40 -c4 -l1 -twav
It seems that all channels have been mixed into my two front speakers,
no sound on my two rear speakers.
I have tried playing movies via mplay
All,
I'm using a Roland UA-1EX
(http://www.rolandus.com/products/productdetails.aspx?ObjectId=743) and
using the optical out.
I'm having some very basic surround sound issues, I believe.
Doing a simple speaker-test -c 6 I see the following output:
speaker-test 1.0.18rc3
Playback
I'm trying to get surround sound working on PS3's (w/ alsa under linux).
I'm able to get Stereo through the SPDIF, and my understanding is that I should
be able to pass-through AC3 encoded audio to get surround sound.
Has any one got this to work, or can some-one assert that it can't be done?
On Tue, 5 Jun 2007 09:56:29 +0300
"Vasilis Manolopoulos" <[EMAIL PROTECTED]> wrote:
> Thanks for the reply.
>
> Well I tried your version of .asoundrc file but this gives me no
> surround sound. The aplay -lLv gives among other a
> card.pcm.surround51 output. I think that by using slave.pcm
> "su
Thanks for the reply.
Well I tried your version of .asoundrc file but this gives me no surround
sound. The aplay -lLv gives among other a card.pcm.surround51 output. I
think that by using slave.pcm "surround51" we use a strandart
implementations of surround sound in the cs46xx file in alsa settin
On Tue, 05 Jun 2007 01:16:55 +0300
Vasilis Manwlopoulos <[EMAIL PROTECTED]> wrote:
> Hi there,
>
>
> I have a Hercules Fortissimo III soundcard which refers to the cs46xx
> chip as far as I know in ALSA modules. I have created a .asoundrc with
> the following:
>
> pcm.!default {
>type plug
Hi there,
I have a Hercules Fortissimo III soundcard which refers to the cs46xx
chip as far as I know in ALSA modules. I have created a .asoundrc with
the following:
pcm.!default {
type plug
slave.pcm "surround51"
slave.channels 6
route_policy duplicate
}
in order to enable surroun
Sorin Peste wrote:
> Hello,
>
> I've got an issue with the M-Audio Revolution 5.1 card. Basically, I can
> only get it to output 2.0 stereo; the LFE, center, and surround channels
> are silent.
>
> ALSA 1.0.13, OpenSUSE 10.1 stock RPMs.
>
> I ran alsaconf and configured the card with the ice1724 dr
Hi!
I didn't see you trying the following command, which, in contrary to the
commands below, should work:
speaker-test -c -Dsurround51
This plays a 6 channel audio stream on a 6 channel device. The commands
below played 2 channel streams on 6 channel devices or 6 channel streams
on 2 channel dev
Hello,
I've got an issue with the M-Audio Revolution 5.1 card. Basically, I can
only get it to output 2.0 stereo; the LFE, center, and surround channels
are silent.
ALSA 1.0.13, OpenSUSE 10.1 stock RPMs.
I ran alsaconf and configured the card with the ice1724 driver (I
previously had an onboard
On Sun, 2006-10-22 at 14:18 +0200, Dominique Dumont wrote:
> Lee Revell <[EMAIL PROTECTED]> writes:
>
> >> (of course without taking into account the sata pb that's plaguing me
> >> ;-) )
> >
> > I'm afraid that is a hardware problem and there's no software solution.
>
> :-(
>
> The only way to
Lee Revell <[EMAIL PROTECTED]> writes:
>> (of course without taking into account the sata pb that's plaguing me
>> ;-) )
>
> I'm afraid that is a hardware problem and there's no software solution.
:-(
The only way to be sure is to check how this stuff works with
Windoze. This is going to take a
On Sat, 2006-10-14 at 22:40 +0200, Dominique Dumont wrote:
> Lee Revell <[EMAIL PROTECTED]> writes:
>
> >> No you should use:
> >>
> >> ac3dec -C some_ac3_file.ac3
> >
> > No, that will decode the AC3 file on the host in software, what Nathan
> > wants to get working is AC3 passthrough, where t
Lee Revell <[EMAIL PROTECTED]> writes:
>> No you should use:
>>
>> ac3dec -C some_ac3_file.ac3
>
> No, that will decode the AC3 file on the host in software, what Nathan
> wants to get working is AC3 passthrough, where the receiver does the AC3
> decoding.
Sorry, I must respecfully disagree. I
On Sat, 2006-10-14 at 12:15 +0200, Dominique Dumont wrote:
> "Nathan A. Smith" <[EMAIL PROTECTED]> writes:
>
> > Does that mean I should do something like this:
> >
> > speaker-test -Dplug:iec958 -c6 -w SURROUNDTEST_011212.wav
> >
> > where the wav file is a ac3 encoded file?
>
> No you should us
"Nathan A. Smith" <[EMAIL PROTECTED]> writes:
> Does that mean I should do something like this:
>
> speaker-test -Dplug:iec958 -c6 -w SURROUNDTEST_011212.wav
>
> where the wav file is a ac3 encoded file?
No you should use:
ac3dec -C some_ac3_file.ac3
HTH
---
Am Samstag 14 Oktober 2006 05:09 schrieb Lee Revell:
> I'm not really a home theater expert, but the DVD standard is AC3 which
> is also known as DD.
DVD standard limits bitrate to 448kbits, though ac3 allows up to 640kbit.
> DTS is an older, less common format.
Nope, it's actually newer, but an
On Fri, 2006-10-13 at 22:52 -0400, Nathan A. Smith wrote:
> On Fri, 2006-10-13 at 22:39 -0400, Lee Revell wrote:
> > I think that's a DTS/DD file. Try this one:
> >
> > http://downloads.lightspeed.cx/lynne/bjorn_lynne-secret_world_(surround_version).ac3
> First off
>
> Nice song -- I might h
On Fri, 2006-10-13 at 22:39 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 22:16 -0400, Nathan A. Smith wrote:
> > Playing SURROUNDTEST_011212.wav.
> > Audio file file format detected.
> > ==
> > Forced audio codec: hwac3
> >
On Fri, 2006-10-13 at 22:16 -0400, Nathan A. Smith wrote:
> Playing SURROUNDTEST_011212.wav.
> Audio file file format detected.
> ==
> Forced audio codec: hwac3
> Cannot find codec for audio format 0x2001.
> Read DOCS/HTML/en/c
On Fri, 2006-10-13 at 22:06 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 21:48 -0400, Nathan A. Smith wrote:
> > BTW: using files from
> > http://www.sr.se/cgi-bin/mall/index.asp?programid=2445
> >
> > I ran "aplay -v ..." and got the following,
> >
> >
> > aplay -v SURROUNDTEST_DD_640.wav
On Fri, 2006-10-13 at 21:48 -0400, Nathan A. Smith wrote:
> BTW: using files from
> http://www.sr.se/cgi-bin/mall/index.asp?programid=2445
>
> I ran "aplay -v ..." and got the following,
>
>
> aplay -v SURROUNDTEST_DD_640.wav
Are you still testing AC3/DTS/etc passthrough? aplay won't play tho
On Fri, 2006-10-13 at 21:48 -0400, Nathan A. Smith wrote:
> On Fri, 2006-10-13 at 19:05 -0400, Nathan A. Smith wrote:
> > On Fri, 2006-10-13 at 18:50 -0400, Gordon McLellan wrote:
> > > just to chime in ... I have a similar pioneer
> > >
> > > look on your display, where the little digital / analo
On Fri, 2006-10-13 at 19:05 -0400, Nathan A. Smith wrote:
> On Fri, 2006-10-13 at 18:50 -0400, Gordon McLellan wrote:
> > just to chime in ... I have a similar pioneer
> >
> > look on your display, where the little digital / analog display box
> > is. when receiving a encoded pcm bitstream, the d
On Fri, 2006-10-13 at 18:50 -0400, Gordon McLellan wrote:
> just to chime in ... I have a similar pioneer
>
> look on your display, where the little digital / analog display box
> is. when receiving a encoded pcm bitstream, the display will show:
>
> DOLBY
> DIGITAL
>
> or
>
> DIGITAL
> DTS
>
just to chime in ... I have a similar pioneer
look on your display, where the little digital / analog display box
is. when receiving a encoded pcm bitstream, the display will show:
DOLBY
DIGITAL
or
DIGITAL
DTS
depending on the encoding used... when a normal non-encoded pcm is
received the ind
On Fri, 2006-10-13 at 17:57 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 17:39 -0400, Nathan A. Smith wrote:
> > > Does the receiver indicate an AC3 signal rather than standard PCM?
> > No, nothing visibile on my receiver.
>
> Do you mean the receiver has no way to display whether it's receiv
On Fri, 2006-10-13 at 17:39 -0400, Nathan A. Smith wrote:
> > Does the receiver indicate an AC3 signal rather than standard PCM?
> No, nothing visibile on my receiver.
Do you mean the receiver has no way to display whether it's receiving
PCM or AC3, or that the indicator is not active?
Lee
---
On Fri, 2006-10-13 at 17:05 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 16:52 -0400, Nathan A. Smith wrote:
> > On Fri, 2006-10-13 at 16:36 -0400, Lee Revell wrote:
> > > On Fri, 2006-10-13 at 16:34 -0400, Nathan A. Smith wrote:
> > > > On Fri, 2006-10-13 at 09:56 -0400, Lee Revell wrote:
> >
On Fri, 2006-10-13 at 16:52 -0400, Nathan A. Smith wrote:
> On Fri, 2006-10-13 at 16:36 -0400, Lee Revell wrote:
> > On Fri, 2006-10-13 at 16:34 -0400, Nathan A. Smith wrote:
> > > On Fri, 2006-10-13 at 09:56 -0400, Lee Revell wrote:
> > > > On Fri, 2006-10-13 at 04:10 -0400, Nathan A. Smith wrote:
On Fri, 2006-10-13 at 16:36 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 16:34 -0400, Nathan A. Smith wrote:
> > On Fri, 2006-10-13 at 09:56 -0400, Lee Revell wrote:
> > > On Fri, 2006-10-13 at 04:10 -0400, Nathan A. Smith wrote:
> > > > Unfortunately, I still am unable to get surround sound to
On Fri, 2006-10-13 at 16:34 -0400, Nathan A. Smith wrote:
> On Fri, 2006-10-13 at 09:56 -0400, Lee Revell wrote:
> > On Fri, 2006-10-13 at 04:10 -0400, Nathan A. Smith wrote:
> > > Unfortunately, I still am unable to get surround sound to work. The
> > > way we were testing this is
> > > with "sp
On Fri, 2006-10-13 at 09:56 -0400, Lee Revell wrote:
> On Fri, 2006-10-13 at 04:10 -0400, Nathan A. Smith wrote:
> > Unfortunately, I still am unable to get surround sound to work. The
> > way we were testing this is
> > with "speaker-test -Dplug:iec958 -c6" (note: iec958 and spdif are the
> > s
On Fri, 2006-10-13 at 04:10 -0400, Nathan A. Smith wrote:
> Unfortunately, I still am unable to get surround sound to work. The
> way we were testing this is
> with "speaker-test -Dplug:iec958 -c6" (note: iec958 and spdif are the
> same for this motherboard).
> I am getting sound from my left an
Hi,
I am running a mythtv box based on Mandriva 2007 on a AMD 3200xp (Dual
core) on an AM2 chipset. I am attempting to get surround sound audio out to my
stereo
via an optical s/pidf cable.
With some help from kirberich && crimsum I adjusted the model= line in my
modprobe.conf
and applied t
I have a Terratec Aureon 5.1 card, which works fine with an OpenSuse 10
installation, but here's the catch:
playing 6 channel surround sound over mplayer, I get three different
behaviors depending on what output device I use:
hw:0,0 played at 1/3 speed only on the rear speakers
hw:0,1
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Hello all (again),
I was playing round with amixer yesterday and managed to get sound coming out
of my front and rear speakers, how happy I was until I lost the settings..
Anyway, After running alsamixer again and fiddling around, I couldn't stumble
do u play a real 6 channel sound, if not u will never hear...
A way to test is to play a movie with mplayer in the following way :
mplayer -ao alsa9 -channels 6 movie.avi
Or this :
http://dtab.hit.bg/tester.mp3
mplayer -ao alsa9 -channels 6 -af=channels=6:6:0:0:0:2:0:4:1:1:1:3:1:5
-loop 0 tes
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On Tuesday 30 December 2003 8:08 am, raptor wrote:
> to all,
> as it seems this is "strongly hidden feature" :")...
> If u have an "M" on a control in alsamixer, just use "<", ">" instead of
> the arrows to mute/unmute it.. (it took me several days to
to all,
as it seems this is "strongly hidden feature" :")...
If u have an "M" on a control in alsamixer, just use "<", ">" instead of the arrows to
mute/unmute it..
(it took me several days to get this)
As it seems "M"-key does the same thing..
|On 2003-12-28 10:01:28 + Dave Hope <[EMAIL PR
On 2003-12-28 10:01:28 + Dave Hope <[EMAIL PROTECTED]>
wrote:
On Saturday 27 December 2003 8:49 pm, Jason Clouse wrote:
On 2003-12-27 16:58:41 + Dave Hope <[EMAIL PROTECTED]>
wrote:
Hello List,
Having got a lovely surround system for christmas I was slightly
dissapointed
to discover that
On 2003-12-27 16:58:41 + Dave Hope <[EMAIL PROTECTED]>
wrote:
Having got a lovely surround system for christmas I was slightly
dissapointed
to discover that sound would not come out my two rear speakers, but
would out
my front 3 and sub. I realise the information is extremely vague, but
i
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On Saturday 27 December 2003 8:49 pm, Jason Clouse wrote:
> On 2003-12-27 16:58:41 + Dave Hope <[EMAIL PROTECTED]>
>
> wrote:
> > Hello List,
> > Having got a lovely surround system for christmas I was slightly
> > dissapointed
> > to discover that
On 2003-12-27 16:58:41 + Dave Hope <[EMAIL PROTECTED]>
wrote:
Hello List,
Having got a lovely surround system for christmas I was slightly
dissapointed
to discover that sound would not come out my two rear speakers, but
would out
my front 3 and sub. I realise the information is extremely vag
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On Saturday 27 December 2003 7:05 pm, Jason Clouse wrote:
> On 2003-12-27 16:58:41 + Dave Hope <[EMAIL PROTECTED]>
>
> wrote:
> > Having got a lovely surround system for christmas I was slightly
> > dissapointed
> > to discover that sound would not
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Hello List,
Having got a lovely surround system for christmas I was slightly dissapointed
to discover that sound would not come out my two rear speakers, but would out
my front 3 and sub. I realise the information is extremely vague, but is this
a k
On Mon, 2002-09-30 at 23:04, Daniel Belcher wrote:
> I am sure this question has been asked before, and I have been all over
> the alsa mixer, tried various compiles of the alsa drivers with
> different configuration settings, cleaned up and redone my modules.conf
> more times than I can count
I am sure this question has been asked before, and I have been all over
the alsa mixer, tried various compiles of the alsa drivers with
different configuration settings, cleaned up and redone my modules.conf
more times than I can count and still can't get rear sound out of my
sblive 5.1...
Hello,
I have the Creative Live 1024 Player and FourPointSurround 1600.
I'm using the latest Alsa Driver (0.9x), and everything works fine,
but I hear no surround sound !
I downloaded the xmms-alsa-plugin, and activated the surround option,
but with no success ...
Are there any test-files, or ca
Hi,
I've spent most of today (and night ;-) looking for information regarding
surround sound support for the SB Live! card using Alsa, however, I have not
found any answers. My (quite simple) question is:
- Is surround sound supported in Alsa, and if so, how do I enable/use it?
Currently, it
57 matches
Mail list logo
