Stus-List Fwd: Whisker pole

[Richard Bush via CnC-List]

Thanks to all for the responses; FYI, I though I would share the response from 
Forte, the manufacturer...

"The pole is painted in a high quality (Alexseal brand) 2 – part polyurethane 
clear paint and it does serve as UV protection.  Most masts, outriggers, spin 
poles etc are painted with the same paint and last for many years in the direct 
sun.  Having said that, a little extra protection certainly would not hurt.  A 
sun cover for storage would be nice, but if the poles starts to look crappy, it 
can be disassembled and repainted and it will look good again.  As far as 
cleaning, you can treat it just like it was a painted fiberglass surface 
(similar to the side of your boat – although that is probably gelcoat).  Most 
importantly I would say would be to keep sand out of it.    I don’t think I 
would worry too much about heat build up from the sun, the carbon fiber tubes 
are cured at 300F and the Tg is around 220F.  So they would have to get up past 
220 before they epoxy started to soften and even that wouldnt hurt it as long 
as it wasn’t under a lot of stress when it was that hot.  
 FORTECarbon Fiber Products14 Lorenz Industrial PkwyLedyard, CT 
06339860-464-5221www.fortecarbon.com 
www.facebook.com/fortecarbon
___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[Richard Bush via CnC-List]

 the cooling pump on my Yanmar 3HMF has a drip which I need to repair or 
replace; there are no marine Yanmar dealers in our area; the Yanmar dealer for 
us is Mastry in St., Petersburg Florida; they want $500+ for a new pump; anyone 
have any suggestions? Thanks
Richard
 
s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
Richard N. Bush Law Offices 
2950 Breckenridge Lane, Suite Nine 
Louisville, Kentucky 40220-1462 
502-584-7255 
 
-Original Message-
From: Bill Coleman via CnC-List 
To: cnc-list 
Cc: Bill Coleman 
Sent: Thu, Apr 2, 2020 9:35 pm
Subject: Re: Stus-List Carbon Fiber Whisker Pole

 #yiv5681438084 #yiv5681438084 -- _filtered {} _filtered {} _filtered {} 
_filtered {} #yiv5681438084 #yiv5681438084 p.yiv5681438084MsoNormal, 
#yiv5681438084 li.yiv5681438084MsoNormal, #yiv5681438084 
div.yiv5681438084MsoNormal 
{margin:0in;margin-bottom:.0001pt;font-size:12.0pt;font-family:New;} 
#yiv5681438084 a:link, #yiv5681438084 span.yiv5681438084MsoHyperlink 
{color:blue;text-decoration:underline;} #yiv5681438084 a:visited, 
#yiv5681438084 span.yiv5681438084MsoHyperlinkFollowed 
{color:purple;text-decoration:underline;} #yiv5681438084 
span.yiv5681438084EmailStyle17 {color:#1F497D;} #yiv5681438084 
.yiv5681438084MsoChpDefault {} _filtered {} #yiv5681438084 
div.yiv5681438084Section1 {} #yiv5681438084 As long as you keep the clear coat 
on, and protected, you shouldbe good. My pole peeled a little, and I got some 
clear coat, but never gotaround to re-Applying it.  I don’t think it will 
normally peel, unless it isnicked, then it starts.  If you touch it up right 
away, you can nip it in thebud.  They say a good polymer on the clear coat, 
like ReJex will  do a good jobof protecting the clear coat, while the clear 
coat protects the epoxy in thecarbon fiber.    My neighbor has a clear-coat 
carbon fiber spar on his J-160, andI don’t think it has been touched since 
1997. Or, if you want to baby it,  I have seen some guys in the fleetput a 
little cloth bag under the boom, and store it there.    Bill Coleman Erie PA    
From: CnC-List[mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Richard Bush 
viaCnC-List
Sent: Thursday, April 02, 2020 5:18 PM
To: cnc-list@cnc-list.com
Cc: Richard Bush
Subject: Re: Stus-List Carbon Fiber Whisker Pole    Listers; I recently 
acquired acarbon fiber whisker pole; 12-22ft X 3.5 in;  (Defender sale); I 
amlooking for advice on how to protect the pole from UV rays; I have seen 
somephotos of the pole deployed on deck with a sunbrella fabric cover; is this 
thebest way? Any better ideas? Are these covers commercially available or 
should Ihave one custom made? Many thanks in advance;      Richard s/v 
Bushmark4:1985 C&C 37 CB; Ohio River, Mile 596;    Richard N. Bush Law Offices  
2950 Breckenridge Lane, Suite Nine  Louisville, Kentucky 40220-1462  
502-584-7255       -Original Message-
From: David Risch via CnC-List 
To: cnc-list@cnc-list.com 
Cc: David Risch 
Sent: Thu, Apr 2, 2020 4:38 pm
Subject: Re: Stus-List Water fill hose question Internal ribbing  impedeaflow 
and reduces pump capacity Sent from my Android. Please forgive typos. Thank 
you.     From: CnC-List  on behalf of 
BillColeman via CnC-List 
Sent: Thursday, April 2, 2020 4:29:44 PM
To: cnc-list@cnc-list.com 
Cc: Bill Coleman 
Subject: Re: Stus-List Water fill hose question    I agree, that is what I use 
formost of my thru hulls as well.
Sirco has a husky vinyl hose with a green spiral reinforcing. 

https://www.sircoindustrialerie.com/


Bill Coleman
Erie PA

-Original Message-
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com]On Behalf Of Len Mitchell 
via CnC-List
Sent: Thursday, April 02, 2020 4:13 PM
To: CNC List
Cc: Len Mitchell
Subject: Stus-List Water fill hose question

When replacing the original ribbed hose or even drain hose I use the 
reinforcedclear vinyl beverage hose. It’s strong, flexible enough and will be 
easier tosource too. 
Len

Sent from my iPad
___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray



___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray 
___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --  https://www.paypal.me/stumurray 
___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --  https:/

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[ALAN BERGEN via CnC-List]

Tri marine pump direct.com. I got a direct replacement from them for a 3gmf
at about half the price of a Yanmar pump.

Alan Bergen
35 Mk III Thirsty
Rose City YC
Portland, OR

On Mon, Apr 6, 2020 at 10:54 AM Richard Bush via CnC-List <
cnc-list@cnc-list.com> wrote:

> the cooling pump on my Yanmar 3HMF has a drip which I need to repair or
> replace; there are no marine Yanmar dealers in our area; the Yanmar dealer
> for us is Mastry in St., Petersburg Florida; they want $500+ for a new
> pump; anyone have any suggestions? Thanks
> Richard
>
> s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
> Richard N. Bush Law Offices
> 2950 Breckenridge Lane, Suite Nine
> Louisville, Kentucky 40220-1462
> 502-584-7255
>
>
> -Original Message-
> From: Bill Coleman via CnC-List 
> To: cnc-list 
> Cc: Bill Coleman 
> Sent: Thu, Apr 2, 2020 9:35 pm
> Subject: Re: Stus-List Carbon Fiber Whisker Pole
>
> As long as you keep the clear coat on, and protected, you should be good.
> My pole peeled a little, and I got some clear coat, but never got around to
> re-Applying it.  I don’t think it will normally peel, unless it is nicked,
> then it starts.  If you touch it up right away, you can nip it in the bud.
> They say a good polymer on the clear coat, like ReJex will  do a good job
> of protecting the clear coat, while the clear coat protects the epoxy in
> the carbon fiber.
>
> My neighbor has a clear-coat carbon fiber spar on his J-160, and I don’t
> think it has been touched since 1997.
> Or, if you want to baby it,  I have seen some guys in the fleet put a
> little cloth bag under the boom, and store it there.
>
> Bill Coleman
> Erie PA
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Richard
> Bush via CnC-List
> *Sent:* Thursday, April 02, 2020 5:18 PM
> *To:* cnc-list@cnc-list.com
> *Cc:* Richard Bush
> *Subject:* Re: Stus-List Carbon Fiber Whisker Pole
>
> Listers; I recently acquired a carbon fiber whisker pole; 12-22ft X 3.5
> in;  (Defender sale); I am looking for advice on how to protect the pole
> from UV rays; I have seen some photos of the pole deployed on deck with a
> sunbrella fabric cover; is this the best way? Any better ideas? Are these
> covers commercially available or should I have one custom made? Many thanks
> in advance;
>
> Richard
> s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
>
> Richard N. Bush Law Offices
> 2950 Breckenridge Lane, Suite Nine
> Louisville, Kentucky 40220-1462
> 502-584-7255
>
>
> -Original Message-
> From: David Risch via CnC-List 
> To: cnc-list@cnc-list.com 
> Cc: David Risch 
> Sent: Thu, Apr 2, 2020 4:38 pm
> Subject: Re: Stus-List Water fill hose question
> Internal ribbing  impedea flow and reduces pump capacity
> Sent from my Android. Please forgive typos. Thank you.
>
> --
> *From:* CnC-List  on behalf of Bill
> Coleman via CnC-List 
> *Sent:* Thursday, April 2, 2020 4:29:44 PM
> *To:* cnc-list@cnc-list.com 
> *Cc:* Bill Coleman 
> *Subject:* Re: Stus-List Water fill hose question
>
> I agree, that is what I use for most of my thru hulls as well.
> Sirco has a husky vinyl hose with a green spiral reinforcing.
>
> https://www.sircoindustrialerie.com/
> 
>
>
> Bill Coleman
> Erie PA
>
> -Original Message-
> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com
> ] On Behalf Of Len Mitchell via CnC-List
> Sent: Thursday, April 02, 2020 4:13 PM
> To: CNC List
> Cc: Len Mitchell
> Subject: Stus-List Water fill hose question
>
> When replacing the original ribbed hose or even drain hose I use the
> reinforced clear vinyl beverage hose. It’s strong, flexible enough and will
> be easier to source too.
> Len
>
> Sent from my iPad
> ___
>
> Thanks everyone for supporting this list with your contributions.  Each
> and every one is greatly appreciated.  If you want to support the list -
> use PayPal to send contribution --   https://www.paypal.me/stumurray
> 
>
>
>
> ___
>
> Thanks everyone for supporting this list with your contributions.  Each
> and every one is greatly appreciated.  If you want to support the list -
> use PayPal to send contribution --   https://www.paypal.me/stumurray
> 
> ___
>
> Thanks everyone for supporting this list with your contributions.  Each
> and every one is greatly appreciated.  If you want to support the list -
> use PayPal to send contribution --  https://www.paypal.me/stumurray
> 

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[ALAN BERGEN via CnC-List]

That should have been marinepumpdirect.com


On Mon, Apr 6, 2020 at 11:08 AM ALAN BERGEN  wrote:

> Tri marine pump direct.com. I got a direct replacement from them for a
> 3gmf at about half the price of a Yanmar pump.
>
> Alan Bergen
> 35 Mk III Thirsty
> Rose City YC
> Portland, OR
>
> On Mon, Apr 6, 2020 at 10:54 AM Richard Bush via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> the cooling pump on my Yanmar 3HMF has a drip which I need to repair or
>> replace; there are no marine Yanmar dealers in our area; the Yanmar dealer
>> for us is Mastry in St., Petersburg Florida; they want $500+ for a new
>> pump; anyone have any suggestions? Thanks
>> Richard
>>
>> s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
>> Richard N. Bush Law Offices
>> 2950 Breckenridge Lane, Suite Nine
>> Louisville, Kentucky 40220-1462
>> 502-584-7255
>>
>>
>> -Original Message-
>> From: Bill Coleman via CnC-List 
>> To: cnc-list 
>> Cc: Bill Coleman 
>> Sent: Thu, Apr 2, 2020 9:35 pm
>> Subject: Re: Stus-List Carbon Fiber Whisker Pole
>>
>> As long as you keep the clear coat on, and protected, you should be good.
>> My pole peeled a little, and I got some clear coat, but never got around to
>> re-Applying it.  I don’t think it will normally peel, unless it is nicked,
>> then it starts.  If you touch it up right away, you can nip it in the bud.
>> They say a good polymer on the clear coat, like ReJex will  do a good job
>> of protecting the clear coat, while the clear coat protects the epoxy in
>> the carbon fiber.
>>
>> My neighbor has a clear-coat carbon fiber spar on his J-160, and I don’t
>> think it has been touched since 1997.
>> Or, if you want to baby it,  I have seen some guys in the fleet put a
>> little cloth bag under the boom, and store it there.
>>
>> Bill Coleman
>> Erie PA
>>
>> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of 
>> *Richard
>> Bush via CnC-List
>> *Sent:* Thursday, April 02, 2020 5:18 PM
>> *To:* cnc-list@cnc-list.com
>> *Cc:* Richard Bush
>> *Subject:* Re: Stus-List Carbon Fiber Whisker Pole
>>
>> Listers; I recently acquired a carbon fiber whisker pole; 12-22ft X 3.5
>> in;  (Defender sale); I am looking for advice on how to protect the pole
>> from UV rays; I have seen some photos of the pole deployed on deck with a
>> sunbrella fabric cover; is this the best way? Any better ideas? Are these
>> covers commercially available or should I have one custom made? Many thanks
>> in advance;
>>
>> Richard
>> s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
>>
>> Richard N. Bush Law Offices
>> 2950 Breckenridge Lane, Suite Nine
>> Louisville, Kentucky 40220-1462
>> 502-584-7255
>>
>>
>> -Original Message-
>> From: David Risch via CnC-List 
>> To: cnc-list@cnc-list.com 
>> Cc: David Risch 
>> Sent: Thu, Apr 2, 2020 4:38 pm
>> Subject: Re: Stus-List Water fill hose question
>> Internal ribbing  impedea flow and reduces pump capacity
>> Sent from my Android. Please forgive typos. Thank you.
>>
>> --
>> *From:* CnC-List  on behalf of Bill
>> Coleman via CnC-List 
>> *Sent:* Thursday, April 2, 2020 4:29:44 PM
>> *To:* cnc-list@cnc-list.com 
>> *Cc:* Bill Coleman 
>> *Subject:* Re: Stus-List Water fill hose question
>>
>> I agree, that is what I use for most of my thru hulls as well.
>> Sirco has a husky vinyl hose with a green spiral reinforcing.
>>
>> https://www.sircoindustrialerie.com/
>> 
>>
>>
>> Bill Coleman
>> Erie PA
>>
>> -Original Message-
>> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com
>> ] On Behalf Of Len Mitchell via CnC-List
>> Sent: Thursday, April 02, 2020 4:13 PM
>> To: CNC List
>> Cc: Len Mitchell
>> Subject: Stus-List Water fill hose question
>>
>> When replacing the original ribbed hose or even drain hose I use the
>> reinforced clear vinyl beverage hose. It’s strong, flexible enough and will
>> be easier to source too.
>> Len
>>
>> Sent from my iPad
>> ___
>>
>> Thanks everyone for supporting this list with your contributions.  Each
>> and every one is greatly appreciated.  If you want to support the list -
>> use PayPal to send contribution --   https://www.paypal.me/stumurray
>> 
>>
>>
>>
>> ___
>>
>> Thanks everyone for supporting this list with your contributions.  Each
>> and every one is greatly appreciated.  If you want to support the list -
>> use PayPal to send contribution --   https://www.paypal.me/stumurray
>> 
>> ___
>

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[Richard Bush via CnC-List]

 Alan, I will! thanks
 
Richard
 
Richard N. Bush Law Offices 
2950 Breckenridge Lane, Suite Nine 
Louisville, Kentucky 40220-1462 
502-584-7255 
 
-Original Message-
From: ALAN BERGEN via CnC-List 
To: C&C 
Cc: ALAN BERGEN 
Sent: Mon, Apr 6, 2020 2:10 pm
Subject: Re: Stus-List Sea water cooling pump for Yanmar 3HMF

That should have been marinepumpdirect.com

On Mon, Apr 6, 2020 at 11:08 AM ALAN BERGEN  wrote:

Tri marine pump direct.com. I got a direct replacement from them for a 3gmf at 
about half the price of a Yanmar pump.
Alan Bergen35 Mk III ThirstyRose City YCPortland, OR

On Mon, Apr 6, 2020 at 10:54 AM Richard Bush via CnC-List 
 wrote:

 the cooling pump on my Yanmar 3HMF has a drip which I need to repair or 
replace; there are no marine Yanmar dealers in our area; the Yanmar dealer for 
us is Mastry in St., Petersburg Florida; they want $500+ for a new pump; anyone 
have any suggestions? Thanks
Richard
 
s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
Richard N. Bush Law Offices 
2950 Breckenridge Lane, Suite Nine 
Louisville, Kentucky 40220-1462 
502-584-7255 
 
-Original Message-
From: Bill Coleman via CnC-List 
To: cnc-list 
Cc: Bill Coleman 
Sent: Thu, Apr 2, 2020 9:35 pm
Subject: Re: Stus-List Carbon Fiber Whisker Pole

As long as you keep the clear coat on, and protected, you shouldbe good. My 
pole peeled a little, and I got some clear coat, but never gotaround to 
re-Applying it.  I don’t think it will normally peel, unless it isnicked, then 
it starts.  If you touch it up right away, you can nip it in thebud.  They say 
a good polymer on the clear coat, like ReJex will  do a good jobof protecting 
the clear coat, while the clear coat protects the epoxy in thecarbon fiber.    
My neighbor has a clear-coat carbon fiber spar on his J-160, andI don’t think 
it has been touched since 1997. Or, if you want to baby it,  I have seen some 
guys in the fleetput a little cloth bag under the boom, and store it there.    
Bill Coleman Erie PA    From: CnC-List[mailto:cnc-list-boun...@cnc-list.com] On 
Behalf Of Richard Bush viaCnC-List
Sent: Thursday, April 02, 2020 5:18 PM
To: cnc-list@cnc-list.com
Cc: Richard Bush
Subject: Re: Stus-List Carbon Fiber Whisker Pole    Listers; I recently 
acquired acarbon fiber whisker pole; 12-22ft X 3.5 in;  (Defender sale); I 
amlooking for advice on how to protect the pole from UV rays; I have seen 
somephotos of the pole deployed on deck with a sunbrella fabric cover; is this 
thebest way? Any better ideas? Are these covers commercially available or 
should Ihave one custom made? Many thanks in advance;      Richard s/v 
Bushmark4:1985 C&C 37 CB; Ohio River, Mile 596;    Richard N. Bush Law Offices  
2950 Breckenridge Lane, Suite Nine  Louisville, Kentucky 40220-1462  
502-584-7255       -Original Message-
From: David Risch via CnC-List 
To: cnc-list@cnc-list.com 
Cc: David Risch 
Sent: Thu, Apr 2, 2020 4:38 pm
Subject: Re: Stus-List Water fill hose question Internal ribbing  impedeaflow 
and reduces pump capacity Sent from my Android. Please forgive typos. Thank 
you.     From: CnC-List  on behalf of 
BillColeman via CnC-List 
Sent: Thursday, April 2, 2020 4:29:44 PM
To: cnc-list@cnc-list.com 
Cc: Bill Coleman 
Subject: Re: Stus-List Water fill hose question    I agree, that is what I use 
formost of my thru hulls as well.
Sirco has a husky vinyl hose with a green spiral reinforcing. 

https://www.sircoindustrialerie.com/


Bill Coleman
Erie PA

-Original Message-
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com]On Behalf Of Len Mitchell 
via CnC-List
Sent: Thursday, April 02, 2020 4:13 PM
To: CNC List
Cc: Len Mitchell
Subject: Stus-List Water fill hose question

When replacing the original ribbed hose or even drain hose I use the 
reinforcedclear vinyl beverage hose. It’s strong, flexible enough and will be 
easier tosource too. 
Len

Sent from my iPad
___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray



___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray 
___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --  https://www.paypal.me/stumurray 
___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --  https://www.paypal.me/stumurray

Re: Stus-List Fwd: Whisker pole

[Charlie Nelson via CnC-List]

Great choice Richard--
Both my poles are Forte and have worked well and looked good for 10+ years. I 
thought they were better made and were definitely less expensive than the 
Forespar (?) poles at that time.
Charlie Nelson


-Original Message-
From: Richard Bush via CnC-List 
To: cnc-list 
Cc: Richard Bush 
Sent: Mon, Apr 6, 2020 11:17 am
Subject: Stus-List Fwd: Whisker pole

Thanks to all for the responses; FYI, I though I would share the response from 
Forte, the manufacturer...

"The pole is painted in a high quality (Alexseal brand) 2 – part polyurethane 
clear paint and it does serve as UV protection.  Most masts, outriggers, spin 
poles etc are painted with the same paint and last for many years in the direct 
sun.  Having said that, a little extra protection certainly would not hurt.  A 
sun cover for storage would be nice, but if the poles starts to look crappy, it 
can be disassembled and repainted and it will look good again.  As far as 
cleaning, you can treat it just like it was a painted fiberglass surface 
(similar to the side of your boat – although that is probably gelcoat).  Most 
importantly I would say would be to keep sand out of it.    I don’t think I 
would worry too much about heat build up from the sun, the carbon fiber tubes 
are cured at 300F and the Tg is around 220F.  So they would have to get up past 
220 before they epoxy started to soften and even that wouldnt hurt it as long 
as it wasn’t under a lot of stress when it was that hot.  
 FORTECarbon Fiber Products14 Lorenz Industrial PkwyLedyard, CT 
06339860-464-5221www.fortecarbon.com 
www.facebook.com/fortecarbon
___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --  https://www.paypal.me/stumurray

___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[Charlie Nelson via CnC-List]

Your pump likely has a rear O-ring seal on the shaft that may be shot--or the 
shaft may be 'scored' from this O-ring after it broke up, etc. If the scoring 
is slight, you may get away with some fine sanding and a new O-ring. If the 
scoring is significant, you probably need to go for the entire pump--I doubt 
that you could source the shaft only.
Charlie Nelson


-Original Message-
From: Richard Bush via CnC-List 
To: cnc-list 
Cc: Richard Bush 
Sent: Mon, Apr 6, 2020 2:39 pm
Subject: Re: Stus-List Sea water cooling pump for Yanmar 3HMF

 Alan, I will! thanks
 
Richard
 
Richard N. Bush Law Offices 
2950 Breckenridge Lane, Suite Nine 
Louisville, Kentucky 40220-1462 
502-584-7255 
 
-Original Message-
From: ALAN BERGEN via CnC-List 
To: C&C 
Cc: ALAN BERGEN 
Sent: Mon, Apr 6, 2020 2:10 pm
Subject: Re: Stus-List Sea water cooling pump for Yanmar 3HMF

That should have been marinepumpdirect.com

On Mon, Apr 6, 2020 at 11:08 AM ALAN BERGEN  wrote:

Tri marine pump direct.com. I got a direct replacement from them for a 3gmf at 
about half the price of a Yanmar pump.
Alan Bergen35 Mk III ThirstyRose City YCPortland, OR

On Mon, Apr 6, 2020 at 10:54 AM Richard Bush via CnC-List 
 wrote:

 the cooling pump on my Yanmar 3HMF has a drip which I need to repair or 
replace; there are no marine Yanmar dealers in our area; the Yanmar dealer for 
us is Mastry in St., Petersburg Florida; they want $500+ for a new pump; anyone 
have any suggestions? Thanks
Richard
 
s/v Bushmark4: 1985 C&C 37 CB; Ohio River, Mile 596;
Richard N. Bush Law Offices 
2950 Breckenridge Lane, Suite Nine 
Louisville, Kentucky 40220-1462 
502-584-7255 
 
-Original Message-
From: Bill Coleman via CnC-List 
To: cnc-list 
Cc: Bill Coleman 
Sent: Thu, Apr 2, 2020 9:35 pm
Subject: Re: Stus-List Carbon Fiber Whisker Pole

As long as you keep the clear coat on, and protected, you shouldbe good. My 
pole peeled a little, and I got some clear coat, but never gotaround to 
re-Applying it.  I don’t think it will normally peel, unless it isnicked, then 
it starts.  If you touch it up right away, you can nip it in thebud.  They say 
a good polymer on the clear coat, like ReJex will  do a good jobof protecting 
the clear coat, while the clear coat protects the epoxy in thecarbon fiber.    
My neighbor has a clear-coat carbon fiber spar on his J-160, andI don’t think 
it has been touched since 1997. Or, if you want to baby it,  I have seen some 
guys in the fleetput a little cloth bag under the boom, and store it there.    
Bill Coleman Erie PA    From: CnC-List[mailto:cnc-list-boun...@cnc-list.com] On 
Behalf Of Richard Bush viaCnC-List
Sent: Thursday, April 02, 2020 5:18 PM
To: cnc-list@cnc-list.com
Cc: Richard Bush
Subject: Re: Stus-List Carbon Fiber Whisker Pole    Listers; I recently 
acquired acarbon fiber whisker pole; 12-22ft X 3.5 in;  (Defender sale); I 
amlooking for advice on how to protect the pole from UV rays; I have seen 
somephotos of the pole deployed on deck with a sunbrella fabric cover; is this 
thebest way? Any better ideas? Are these covers commercially available or 
should Ihave one custom made? Many thanks in advance;      Richard s/v 
Bushmark4:1985 C&C 37 CB; Ohio River, Mile 596;    Richard N. Bush Law Offices  
2950 Breckenridge Lane, Suite Nine  Louisville, Kentucky 40220-1462  
502-584-7255       -Original Message-
From: David Risch via CnC-List 
To: cnc-list@cnc-list.com 
Cc: David Risch 
Sent: Thu, Apr 2, 2020 4:38 pm
Subject: Re: Stus-List Water fill hose question Internal ribbing  impedeaflow 
and reduces pump capacity Sent from my Android. Please forgive typos. Thank 
you.     From: CnC-List  on behalf of 
BillColeman via CnC-List 
Sent: Thursday, April 2, 2020 4:29:44 PM
To: cnc-list@cnc-list.com 
Cc: Bill Coleman 
Subject: Re: Stus-List Water fill hose question    I agree, that is what I use 
formost of my thru hulls as well.
Sirco has a husky vinyl hose with a green spiral reinforcing. 

https://www.sircoindustrialerie.com/


Bill Coleman
Erie PA

-Original Message-
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com]On Behalf Of Len Mitchell 
via CnC-List
Sent: Thursday, April 02, 2020 4:13 PM
To: CNC List
Cc: Len Mitchell
Subject: Stus-List Water fill hose question

When replacing the original ribbed hose or even drain hose I use the 
reinforcedclear vinyl beverage hose. It’s strong, flexible enough and will be 
easier tosource too. 
Len

Sent from my iPad
___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray



___

Thanks everyone for supporting this list with your contributions.  Eachand 
every one is greatly appreciated.  If you want to support the list -use PayPal 
to send contribution --   https://www.paypal.me/stumurray 
__

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[Doug Mountjoy via CnC-List]

Most sea water pumps can be rebuilt, new bearings, seals. I did my yanmar pump 
for about 1/2 of new.  Doug Mountjoysv Rebecca Leah C&C Landfall 39Port Orchard 
yacht club
null___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Re: Stus-List Sea water cooling pump for Yanmar 3HMF

[Hoyt, Mike via CnC-List]

Wait .. is this the fresh water pump or the raw water pump?  We replaced fresh 
water pump on persistence in 2015 and I di not recall it being expensive.  Was 
3GM30F but I would think the newer engine pumps would not be that different or 
more expensive. In summer 2011 the yanmar fresh water pump for 3GM30F from 
local dealer was $211 CDN (approx. $0.50 USD).

Hope this helps

Mike



From: CnC-List  On Behalf Of Doug Mountjoy via 
CnC-List
Sent: April 6, 2020 4:40 PM
To: cnc-list@cnc-list.com
Cc: Doug Mountjoy 
Subject: Re: Stus-List Sea water cooling pump for Yanmar 3HMF

Most sea water pumps can be rebuilt, new bearings, seals. I did my yanmar pump 
for about 1/2 of new.



Doug Mountjoy
sv Rebecca Leah
C&C Landfall 39
Port Orchard yacht club
___

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray