There are options for the image cropping area in the list, no? (-x -y, etc)
I don't know why you want uncalibrated data, it will look terrible. How about you tell us what you are trying to do :) allan On Fri, Feb 11, 2011 at 2:49 PM, Ben Green <greenb1 at mac.com> wrote: > Ha ha - thanks Allan - it worked.. and i pulled up the options too.. > HOWEVER - my (ongoing) problem is that i need to switch off the calibration > section of the scan process so that i receive a raw data feed. > Is there further settings I can effect? For example in the plustec backend, I > was able to adjust crop area, gain, calibration on/off etc.. is this just not > an option with genesys? Is there someone who can do such things? (certainly I > can't - i couldn't even get the command into terminal!!) > > > > > > Thanks > > > Ben > > > > On 11 Feb 2011, at 19:38, m. allan noah wrote: > >> It is a command. you run it in the terminal. If you got no text back, >> try running this instead: >> >> scanimage -L >> >> allan >> >> On Fri, Feb 11, 2011 at 2:33 PM, Ben Green <greenb1 at mac.com> wrote: >>> >>> >>> On 10 Feb 2011, at 05:24, stef wrote: >>> >>>> Le Wednesday 09 February 2011 18:01:08 Ben Green, vous avez ?crit : >>>>> Hi >>>>> I'm trying to configure various actions inside my Lide 60 such as >>>>> analogue gain, tinkering with the calibration and the crop area that >>>>> it scans with. >>>>> >>>>> The backend seems to have been abandoned on the support front ?- >>>>> scanning is no problem, worked first time - its just this .conf file >>>>> that i cannot drive? is there a list of commands I can feed into >>>>> the .config file? like lamp on/off, red gain +3 ??? i'm afraid i dont >>>>> speak Genesys? >>>>> >>>>> I have done this with some earlier LIDEs that worked with the plustec >>>>> backend - these were quite straightforward - i could open the SANE >>>>> prefs and turn calibration on/off, change gain and crop just by >>>>> changing some zeros and ones.. however this genesys backend has only a >>>>> list of scanners and their model/product addresses - I don't know what >>>>> commands to put into the .conf file. >>>>> >>>>> I'm using SANE: mac10.6: >>>>> >>>>> ? TWAIN SANE Interface 2.9 binary ?http://www.ellert.se/twain-sane/ >>>>> SANE Preference Pane 0.9 binary http://www.ellert.se/twain-sane/ SANE >>>>> backends http://www.sane-project.org/ ? libusb 0.1.13 beta 2009-09-10 >>>>> binary http://libusb.sourceforge.net/ >>>>> >>>>> >>>>> Any Help is Much Appreciated.. >>>>> >>>>> >>>>> Thnaks >>>>> >>>>> >>>>> Ben >>>> >>>> ? ? ? Hello, >>>> >>>> ? ? ? all user settable settings are published by the backend through >>>> options. >>>> You can get the full list of active options for your model with 'scanimage >>>> -d >>>> genesys --help'. There is no options or settings to modify in the conf >>>> file. >>>> >>>> Regards, >>>> ? ? ? Stef >>>> >>>> -- >>>> sane-devel mailing list: sane-devel at lists.alioth.debian.org >>>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel >>>> Unsubscribe: Send mail with subject "unsubscribe your_password" >>>> ? ? ? ? ? ? to sane-devel-request at lists.alioth.debian.org >>> >>> >>> Hi Steph, >>> >>> Could you tell me how and where I use this command? (scanimage -d genesys >>> --help) >>> Is it in the SANE prefs file? if so, do i enter the command under my >>> particular scanner model? >>> I tried putting this command into terminal but got nothing back - >>> >>> Sorry I cant profess to know much about command line interface.. >>> >>> >>> Thanks for you help.. >>> >>> >>> Ben >>> >>> >>> >>> -- >>> sane-devel mailing list: sane-devel at lists.alioth.debian.org >>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel >>> Unsubscribe: Send mail with subject "unsubscribe your_password" >>> ? ? ? ? ? ? to sane-devel-request at lists.alioth.debian.org >>> >> >> >> >> -- >> "The truth is an offense, but not a sin" > > -- "The truth is an offense, but not a sin"
