Hi Frank, lets start a new test with debugging information. Do
export SANE_DEBUG_HP=17 xscanimage hp > hp.lis 2>&1 gzip hp.lis And please send back the file hp.lis.gz. BTW. What SCSI-card are you using with the scanner ? --Peter Frank Roberts - SOTL wrote: > Thanks again for the help Peter. > I did the following: > 1. Restored sane.d to its original configuration. > 2. In hp.conf changed /dev/scanner to /dev/sg0 > 3. Confirmed that hp is active in dll.conf. > 4. Tested system - no change. > 5. As root did: chmood 666 /dev/sg0 > 6. Tested system - no change. > > Thanks > Frank > > On Monday 05 August 2002 01:14, Peter Kirchgessner wrote: > >>Don't remove the files. You need at least dll.conf too. And check that >>it has the line with hp activated. >> >>--Peter >> >>Frank Roberts - SOTL wrote: >> >>>Thanks for the help Peter. >>> >>>I did the following: >>>1. Changed /dev/scanner to /dev/sg0 >>>2. Made directory sane.d-bak >>>3. Removed all configuration files from sane.d except hp.conf >>>4. As root did chmood 666 /dev/sg0 >>> >>>I received exactly the same results - no change. >>> >>>Thanks >>>Frank >>> >>>On Sunday 04 August 2002 04:06, Peter Kirchgessner wrote: >>> >>>>Hi Frank, >>>> >>>>try the hp.conf with >>>>scsi HP >>>>/dev/sg0 >>>> >>>>If this does not work, you may have a second hp.conf at >>>>/etc/sane.d/hp.conf. Try that one with the same content. >>>>If it still does not work, do as root a >>>> >>>>chmod 666 /dev/sg0 >>>>and try it again. >>>> >>>>Sincerely >>>>Peter >>>> >>>>Frank Roberts - SOTL wrote: >>>> >>>>>Hi All: >>>>> >>>>>I hope You people will have time to help a relative novice with >>>>>configuration of an HP 6100 C which is to be used intermidently on 2 >>>>>different RH 7.3 systems. >>>>> >>>>> >>>>>As stated previously the scanner is an HP 6100C if I issue the command: >>>>>The scanner is connected by 40 pin scsi. >>>>>Several commands were issues with the following results: >>>>> >>>>>$ scanimage --list devices >>>>>sg0 HP C2520A 36644 >>>>>sg1 Mitsumi CD-R >>>>>sg2 Soney CD-RW >>>>> >>>>> >>>>>$ cat /proc/scsi/scsa >>>>>Attached devices: >>>>>Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev: >>>>>3644 Type: Processor ANSI SCSI revision: 02 >>>>>Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM >>>>>FX4830T!B Rev: R02C Type: CD-ROM ANSI SCSI revision: 02 >>>>>Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW >>>>>CRX175E2 Rev: S002 Type: CD-ROM ANSI SCSI revision: 02 >>>>> >>>>> >>>>>$ export SANE_DEBUGG_HP=17 >>>>>$ scanimage -L >>>>>[scanei_debug] Setting debug level of hp to 17 >>>>>[hp] sane_init called[hp] >>>>>[hp] sane_init will finish with Success >>>>>[hp] sane_get_devices called >>>>>[hp] hp_read_config: hp backend v0.95 start reading conf file >>>>>[hp] hp_read_config: processing line <scsi HP> >>>>>[hp] hp_read_config: processing line </dev/scaner> >>>>>[hp] hp_read_config: attach scsi HP >>>>>[hp] hp_read_config: attach /dev/scanner >>>>>[hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1 >>>>>[hp] sanei_hp_device_new: /dev/scanner >>>>>[hp] scsi_newopen failed (Invalid argument) >>>>>[hp] /dev/scanner: Can't open scsi device >>>>>[hp] sane_get_devices will finish with Success >>>>>[hp] sane_exit called >>>>>[hp] sane_exit will finish >>>>> >>>>> >>>>>The sane configuration file /etc/sane.d/ho.conf is as follows: >>>>>scsi HP >>>>>/dev/scannet >>>>> >>>>>I would appreciate any advice you people may be able to offer. >>>>> >>>>>Thanks >>>>>Frank >>>>> >>>>>Thanks >>>>> > > -- Peter Kirchgessner http://www.kirchgessner.net mailto:pe...@kirchgessner.net
