Thanks again for the help Peter. I did the following: 1. Restored sane.d to its original configuration. 2. In hp.conf changed /dev/scanner to /dev/sg0 3. Confirmed that hp is active in dll.conf. 4. Tested system - no change. 5. As root did: chmood 666 /dev/sg0 6. Tested system - no change.
Thanks Frank On Monday 05 August 2002 01:14, Peter Kirchgessner wrote: > > Don't remove the files. You need at least dll.conf too. And check that > it has the line with hp activated. > > --Peter > > Frank Roberts - SOTL wrote: > > Thanks for the help Peter. > > > > I did the following: > > 1. Changed /dev/scanner to /dev/sg0 > > 2. Made directory sane.d-bak > > 3. Removed all configuration files from sane.d except hp.conf > > 4. As root did chmood 666 /dev/sg0 > > > > I received exactly the same results - no change. > > > > Thanks > > Frank > > > > On Sunday 04 August 2002 04:06, Peter Kirchgessner wrote: > >>Hi Frank, > >> > >>try the hp.conf with > >>scsi HP > >>/dev/sg0 > >> > >>If this does not work, you may have a second hp.conf at > >>/etc/sane.d/hp.conf. Try that one with the same content. > >>If it still does not work, do as root a > >> > >>chmod 666 /dev/sg0 > >>and try it again. > >> > >>Sincerely > >>Peter > >> > >>Frank Roberts - SOTL wrote: > >>>Hi All: > >>> > >>>I hope You people will have time to help a relative novice with > >>>configuration of an HP 6100 C which is to be used intermidently on 2 > >>>different RH 7.3 systems. > >>> > >>> > >>>As stated previously the scanner is an HP 6100C if I issue the command: > >>>The scanner is connected by 40 pin scsi. > >>>Several commands were issues with the following results: > >>> > >>>$ scanimage --list devices > >>>sg0 HP C2520A 36644 > >>>sg1 Mitsumi CD-R > >>>sg2 Soney CD-RW > >>> > >>> > >>>$ cat /proc/scsi/scsa > >>>Attached devices: > >>>Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev: > >>> 3644 Type: Processor ANSI SCSI revision: 02 > >>>Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM > >>>FX4830T!B Rev: R02C Type: CD-ROM ANSI SCSI revision: 02 > >>>Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW > >>> CRX175E2 Rev: S002 Type: CD-ROM ANSI SCSI revision: 02 > >>> > >>> > >>>$ export SANE_DEBUGG_HP=17 > >>>$ scanimage -L > >>>[scanei_debug] Setting debug level of hp to 17 > >>>[hp] sane_init called[hp] > >>>[hp] sane_init will finish with Success > >>>[hp] sane_get_devices called > >>>[hp] hp_read_config: hp backend v0.95 start reading conf file > >>>[hp] hp_read_config: processing line <scsi HP> > >>>[hp] hp_read_config: processing line </dev/scaner> > >>>[hp] hp_read_config: attach scsi HP > >>>[hp] hp_read_config: attach /dev/scanner > >>>[hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1 > >>>[hp] sanei_hp_device_new: /dev/scanner > >>>[hp] scsi_newopen failed (Invalid argument) > >>>[hp] /dev/scanner: Can't open scsi device > >>>[hp] sane_get_devices will finish with Success > >>>[hp] sane_exit called > >>>[hp] sane_exit will finish > >>> > >>> > >>>The sane configuration file /etc/sane.d/ho.conf is as follows: > >>>scsi HP > >>>/dev/scannet > >>> > >>>I would appreciate any advice you people may be able to offer. > >>> > >>>Thanks > >>>Frank > >>> > >>>Thanks
