It was 30 ADC. And it happened after adding the second inverter to increase charge rate. I just checked last info on Optics and found that the 2nd inverter is newer firmware (61 and 68) . I had made sure all other settings were identical on both inverters but didn't look at firmware. Now I realize the 2nd inverter may be fighting with the first one if they have different firmware. Guess I better start there and update the older inverter if possible. Actual charge rate was also half of what it should be based on AC charge current settings.
John On Sun, May 11, 2025 at 10:48 AM Jay via RE-wrenches < [email protected]> wrote: > Hi John > > Do you mean 30 amps dc or AC from the inverter? > > Regardless I can only think the issue is programming. > > Is this a new issue after new equipment or ? > > Jay > > > > On May 10, 2025, at 7:17 PM, John Blittersdorf via RE-wrenches < > [email protected]> wrote: > > > > > > The system is Flexware 500 with 2 VFX3648 Master and slave L1, with > FM100. There are 2 Fortress eVault batteries and MATE3s and HUB. We had a > problem with charging going between 0 and approx 30 amps DC. The current > would climb up in about 10 seconds and then slowly go back to 0 in about > the same amount of time and then repeat. For some reason when we unplugged > the FM100 from the HUB, charging would resume at about 40 ADC continuous > from the generator.. This happens when the sun is out and when dark so the > solar input is having no effect on this strange behavior. Any ideas? > > > > John Blittersdorf > > _______________________________________________ > > List sponsored by Redwood Alliance > > > > Pay optional member dues here: http://re-wrenches.org > > > > List Address: [email protected] > > > > Change listserver email address & settings: > > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > > > There are two list archives for searching. When one doesn't work, try > the other: > > https://www.mail-archive.com/[email protected]/ > > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > > > List rules & etiquette: > > http://www.re-wrenches.org/etiquette.htm > > > > Check out or update participant bios: > > http://www.members.re-wrenches.org > > > _______________________________________________ > List sponsored by Redwood Alliance > > Pay optional member dues here: http://re-wrenches.org > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > There are two list archives for searching. When one doesn't work, try the > other: > https://www.mail-archive.com/[email protected]/ > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > http://www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > http://www.members.re-wrenches.org > >
_______________________________________________ List sponsored by Redwood Alliance Pay optional member dues here: http://re-wrenches.org List Address: [email protected] Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org There are two list archives for searching. When one doesn't work, try the other: https://www.mail-archive.com/[email protected]/ http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: http://www.re-wrenches.org/etiquette.htm Check out or update participant bios: http://www.members.re-wrenches.org
