I have disassembled many of these pallets. On flat ground they stand up very well in their corner protectors. In fact they are a bit difficult to get out. We raise one side of the truck or trailer a bit and let the stack rest against a wall or something heavy and it works just fine.
These have proven to be great panels for us, and we have 180 mph design wind speeds here. It's a solid product. *Jason Szumlanski* Principal Solar Designer | Florida Solar Design Group On Wed, Aug 21, 2019 at 1:33 PM Ryan Harkins <ryan.hark...@energycraft.com> wrote: > Bill, > > Sometimes we add some duct tape to the corner guards on the side-stacked > module skids, so as you unpack you peel tape back one module at a time. > Helps them stay together as a unit and not tip. > > Careful with those Mission modules! We had a couple skids of those and > the corner miters of the frames were off just a little, so the corners of > the modules were like razor blades! They look great though. > > Ryan > > > > On Aug 20, 2019, at 8:31 PM, William Miller <will...@millersolar.com> > wrote: > > > > Bill: > > > > I hope your trailer has side walls. Load the pallet near one side of > your > > trailer. Encourage modules to lean that direction as you cut the > bands. If > > you are worried about travelling with the load off-center, take some > extra > > pallets to stack between the modules and the downhill side of your > trailer. > > The panels tend to stand up when the bands are cut. > > > > William > > > > Miller Solar > > 17395 Oak Road, Atascadero, CA 93422 > > 805-438-5600 > > www.millersolar.com > > CA Lic. 773985 > > > > > > -----Original Message----- > > From: RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] On > > Behalf Of Bill Battagin > > Sent: Tuesday, August 20, 2019 6:27 PM > > To: re-wrenches@lists.re-wrenches.org > > Subject: [RE-wrenches] Mission PVs > > > > Its after hours and I need to load for tomorrow... > > > > Embarrassing question.... I finally ran out of SolarWorld PVs and just > > received a few pallets of Mission MSE310SQ8T PVs. They are stacked on > > their edges. hmmm. I took off the top cardboard, there are still 2 > > bands running around the 26 PVs horizontally and the cardboard around > > the sides. I think only those who have used Mission will know my > > conundrum....What's the next step? > > > > Thanks, > > > > Bill > > > > Feather River Solar Electric > > > > > > --- > > This email has been checked for viruses by Avast antivirus software. > > https://www.avast.com/antivirus > > > > > > _______________________________________________ > > List sponsored by Redwood Alliance > > > > List Address: RE-wrenches@lists.re-wrenches.org > > > > Change listserver email address & settings: > > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > > > List-Archive: > > > http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html > > > > List rules & etiquette: > > www.re-wrenches.org/etiquette.htm > > > > Check out or update participant bios: > > www.members.re-wrenches.org > > _______________________________________________ > > List sponsored by Redwood Alliance > > > > List Address: RE-wrenches@lists.re-wrenches.org > > > > Change listserver email address & settings: > > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > > > List-Archive: > http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html > > > > List rules & etiquette: > > www.re-wrenches.org/etiquette.htm > > > > Check out or update participant bios: > > www.members.re-wrenches.org > > > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org > >
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
