Use a genset for back-up and power it as you said from 240vac inverter. Less is more and a failed DD-DC converter could damage the SQ!
Dave Angelini Offgrid Solar "we go where powerlines don't" http://members.sti.net/offgridsolar/ [1] e-mail offgridso...@sti.net [2] text 209 813 0060 On Tue, 6 Aug 2019 04:31:25 +0000, Tom Duffy wrote: Why don't you go solar direct no batteries? and use AC for your back up as the pump will do both. My experience says at least 60VDC to run the pump so 24 volt battery won't do it. Kind regards TOM DUFFY _SENIOR SOLAR DESIGN ENGINEER_ MAIN TOLL FREE: 888-826-0939 DIRECT: 888-503-6772 INTERNATIONAL: 001-575-539-2111 PANAMA: 507-836-5588 X 122 FAX: 520-844-8442 _WWW.THESOLARBIZ.COM_ FROM: RE-wrenches ON BEHALF OF Gary Higbee SENT: Tuesday, August 21, 2018 12:18 PM TO: re-wrenches@lists.re-wrenches.org SUBJECT: [RE-wrenches] DC-DC converter for SQFlex Hi Wrenches, I'm assisting a customer and well person in replacing a failed Lorentz ETApump (after 15 years of intermittent use). We're looking for a quality DC-DC converter to power a not-yet- ordered Grundfos SQFlex 6 SQF-3 from a 24 V Surrette battery bank (wish it was 48!). The pump draws a max of 8.4A and the curves say we'll need about 600 watts so I figure we'd want at least 70 volts out. Ideal would be a higher DC output, say 200V (save a couple hundred feet of larger copper, greater efficiency) and at least 3A (see questions). The primary power source will be 240V AC but my customer wants a fallback for battery operation. We plan to use the Grundfos IO 101 SQFlex switch box, which will switch to DC if the AC fails. Also the CU 200 SQFlex control unit, so we can accommodate the existing float switch up the hill, etc. The Grundfos tech person I spoke with today said the DC system should be able to supply 8.4A, regardless of the DC voltage.The pump curve says we need 600W for maximum performance at the lift we've got. It seems to me that if we've got 200V and need 600W we'd be drawing 3A. Yet if the Grundfos factory line is there should be 8.4A available that's 1680W. The tech guy said he didn't have specific information why we'd need 8.4A regardless of pump input voltage. The Grundfos Product Guide says: MAX. RATINGS ARE AS FOLLOWS: * MAXIMUM POWER INPUT (P1) OF 1400 W * MAXIMUM CURRENT OF 8.4 A * MAXIMUM SPEED OF 3600 RPM (think I read somewhere it's 3000 rpm for this helical rotor model) THE PUMP DELIVERS ITS MAXIMUM PERFORMANCE WHEN ONE OF THE ABOVE PARAMETERS IS REACHED. Two questions: 1) Do any of you have experience running the SQFlex on DC, and what to make of the 8.4A at any input voltage factory recommendation? Maybe basic amps/volts/power calculations aren't applicable given the pump electronics? 2) Are you aware of any DC-DC converters that will get us from a nominal 24V battery bank to 200V, or somewhere between 70 and 200V, with an appropriate current limiting amp rating to get us at least 600W (depending on thoughts regarding the above question)? Thank you, Gary Gary Higbee Windstream Solar Oregon License 17LRT Renewable Energy Consulting g...@windstreamsolar.com [3] 541-954-3881 -- Links: ------ [1] http://members.sti.net/offgridsolar/ [2] mailto:offgridso...@sti.net [3] mailto:g...@windstreamsolar.com
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
