Yea its tough. I’m trying to make sure I do it right ( whatever that is at this point) and what the customer wants. I”ll check to see if this meets with his approval. Might be the way to go. Thanks for the update as to it being tight.
I”m guessing here, but I can hear him say “ yes but that rubber will compress over time, and then we’ll have the SS washer touching the rail” vs what everyone else is saying “ that the plastic will fail and then it’ll be SS on AL anyway. 1 step forward, 3 steps back. jay > On Jan 28, 2016, at 11:23 AM, Ray Walters <r...@solarray.com> wrote: > > We just had that same concern, but once you torque the connection down there > was no noticeable movement. As someone else mentioned the plastics can be > tough to hold up to UV, temperature, compression, and thermal cycling. Once > that hard plastic cracks and falls out, you definitely will have a loose > connection. > R.Ray Walters > CTO, Solarray, Inc > Nabcep Certified PV Installer, > Licensed Master Electrician > Solar Design Engineer > 303 505-8760 > On 1/28/2016 11:19 AM, jay wrote: >> My hesitation to that is the compressibility of the neoprene. >> >> One of the things I like about nylon or similar hard plastics is they don’t >> compress so you do get a ridged structure. >> >> jay >> >> peltz power >>> On Jan 28, 2016, at 10:15 AM, Ray Walters < >>> <mailto:r...@solarray.com>r...@solarray.com <mailto:r...@solarray.com>> >>> wrote: >>> >>> I would use a SS washer with integrated Neoprene rubber gasket. We use >>> them on roof work, and Unirac uses them under the lag on their roof >>> flashings. >>> <images.jpeg> >>> https://www.copperstate.com/shop/429/neoprene-washers >>> <https://www.copperstate.com/shop/429/neoprene-washers> >>> >>> Thanks, >>> R.Ray Walters >>> CTO, Solarray, Inc >>> Nabcep Certified PV Installer, >>> Licensed Master Electrician >>> Solar Design Engineer >>> 303 505-8760 >>> On 1/28/2016 8:25 AM, Jay wrote: >>>> Hi Larry >>>> >>>> I wasn't planning on installing anything between al and al. Just between >>>> SS and al. So the module will still be bolted directly to the al rack >>>> material. I'm not too worried about the grounding, and certainly not >>>> worried enough to install lay in lugs with copper to each module. >>>> >>>> As lones pointed out, there are parts that would insulate the bolt. >>>> But as the owner hasn't requested that, not going to suggest it! >>>> >>>> I sure didn't plan on stirring the pot like this. >>>> Just really wanted some help on sourcing the washers >>>> >>>> Thanks >>>> >>>> Jay >>>> Peltz power >>>> >>>> On Jan 28, 2016, at 6:49 AM, Starlight Solar Power Systems >>>> <la...@starlightsolar.com <mailto:la...@starlightsolar.com>> wrote: >>>> >>>>> Hey Jay, >>>>> >>>>> I’m still trying to picture this and had a thought: If you isolate the >>>>> module from the rack electrically with these washers, and both are >>>>> grounded, and the two grounds are not at the same potential (different >>>>> length ground runs), you may be creating a path for high voltage into the >>>>> array in event of a near lightning strike. >>>>> >>>>> Also, if the washer is between the two metals, how will you isolate the >>>>> bolt that puts them together from not touching the sides of the holes? >>>>> Perhaps you need to look into non-conductive fasteners as well. >>>>> >>>>> Larry Crutcher >>>>> Starlight Solar Power Systems >>>>> >>>>> >>> >> >> >> >> _______________________________________________ >> List sponsored by Redwood Alliance >> >> List Address: RE-wrenches@lists.re-wrenches.org >> <mailto:RE-wrenches@lists.re-wrenches.org> >> >> Change listserver email address & settings: >> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >> <http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org> >> >> List-Archive: >> http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html >> <http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html> >> >> List rules & etiquette: >> www.re-wrenches.org/etiquette.htm <http://www.re-wrenches.org/etiquette.htm> >> >> Check out or update participant bios: >> www.members.re-wrenches.org <http://www.members.re-wrenches.org/> >> > > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org >
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
