If it has a board there are 2 set screws that are adjustable [ 1- upper set point & 2 lower set point for reconnect] and you need to read the current voltage and then apply a simple formula [using a calculator] figure out the setting to adjust it to. It helped to have 2 DVM's along with a calculator. It has been a long time since I had to set one of these and I have no memory as to the formula. If you cannot find it I still Have an ANANDA Power panel in the shop [new] that may have this style of CC and an instruction book but I would have to rip into the box . Let me know if you cannot find it easier than that. If you cannot I will go rummaging.
I would suggest an Outback Flexware or like style upgrade, it would be a lot kinder to the battery bank. Dana Orzel Great Solar Works, Inc www.solarwork.com E - d...@solarwork.com V - 970.626.5253 F - 970.626.4140 C - 970.209.4076 "I'd put my money on solar energy. I hope we don't have to wait 'til oil and coal run out before we tackle that." -Thomas Edison, in conversation with Henry Ford and Harvey Firestone, March 1931 From: re-wrenches-boun...@lists.re-wrenches.org [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Drake Chamberlin Sent: Wednesday, July 15, 2009 7:47 AM To: RE-wrenches Subject: Re: [RE-wrenches] Pulse Power CC Thanks Dana and Brian, I will look for a board next time I'm out. I might try calling Bill Barnickol if necessary. -Drake At 04:56 PM 7/14/2009, you wrote: Content-Type: multipart/alternative; boundary="----=_NextPart_000_0044_01CA0493.564693D0" Content-Language: en-us Does it have a charge controller card mounted in the door? Dana Orzel Great Solar Works, Inc www.solarwork.com <http://www.solarwork.com/> E - d...@solarwork.com V - 970.626.5253 F - 970.626.4140 C - 970.209.4076 "I'd put my money on solar energy. I hope we don't have to wait 'til oil and coal run out before we tackle that." -Thomas Edison, in conversation with Henry Ford and Harvey Firestone, March 1931 From: re-wrenches-boun...@lists.re-wrenches.org [ <mailto:re-wrenches-boun...@lists.re-wrenches.org> mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Drake Chamberlin Sent: Tuesday, July 14, 2009 8:05 AM To: RE-wrenches Subject: [RE-wrenches] Pulse Power CC Is there any way to adjust the voltage on the charge control of a Pulse Power Center? Drake Chamberlin Athens Electric OH License 44810 CO License 3773 NABCEP TM Certified PV Installer Office - 740-448-7328 Mobile - 740-856-9648 _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org <http://www.members.re-wrenches.org/> Drake Chamberlin Athens Electric OH License 44810 CO License 3773 NABCEP TM Certified PV Installer Office - 740-448-7328 Mobile - 740-856-9648
_______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org
