Hi,
I am trying to install OpenBSD 7.0 macppc on a PoweMac7,3, 2x 2.5GHz.
The install70.iso boots up just fine, but none of my two hard drives, which are
connected using SATA, are recognized by the installer.
Poking around with the shell of the install disk, fdisk wd0 or fdisk sd0 just
says "fdisk: opendev('wd0', 0x0): Device not configured“ for the respective
device. Same for disklabel.
Attached is the dmesg I have extracted with a USB stick (gets then recognized
fine as sd0 and fdisk/disklabel on it work).
The following part seems particularly interesting:
pciide0 at pci8 dev 12 function 0 "ServerWorks K2 SATA" rev 0x00: DMA
pciide0: using irq 0 for native-PCI interrupt
pciide0: port 0: 1.5Gb/s
pciide0: port 1: 1.5Gb/s
pciide0: port 2: PHY offline
pciide0: port 3: PHY offline
If I remove one of the harddrives, one of the 1.5Gb/s entries changes to PHY
offline too, but that is as far as I got.
Any hints or ideas how to debug this further?
Cheers
Florian
console out [NVDA,Display-B] console in [keyboard], using USB
using parent NVDA,Parent:: memaddr 98000000, size 8000000 : consaddr 98004000 :
ioaddr 91000000, size 1000000: width 1920 linebytes 2048 height 1080 depth 8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2021 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 7.0 (RAMDISK) #898: Sat Oct 2 00:32:11 MDT 2021
dera...@macppc.openbsd.org:/usr/src/sys/arch/macppc/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1018093568 (970MB)
random: boothowto does not indicate good seed
mainbus0 at root: model PowerMac7,3
cpu0 at mainbus0: 970FX (Revision 0x300): 2500 MHz
cpu at mainbus0 not configured
mem at mainbus0 not configured
memc0 at mainbus0: u3 rev 0x35
kiic0 at memc0 offset 0xf8001000
iic0 at kiic0
"pulsar-legacy-slewing" at iic0 addr 0x6a not configured
"ds1775" at iic0 addr 0x4a not configured
"max6690" at iic0 addr 0x4c not configured
"ds1631" at iic0 addr 0x4b not configured
fcu0 at iic0 addr 0xaf
"pca9556" at iic0 addr 0x18 not configured
"ad7417" at iic0 addr 0x2c not configured
"24256" at iic0 addr 0x50 not configured
"pca9556" at iic0 addr 0x19 not configured
"ad7417" at iic0 addr 0x2d not configured
"24256" at iic0 addr 0x51 not configured
"dart" at memc0 offset 0xf8033000 not configured
"mpic" at memc0 offset 0xf8040000 not configured
mpcpcibr0 at mainbus0 pci: u3-agp
pci0 at mpcpcibr0 bus 0
pchb0 at pci0 dev 11 function 0 "Apple K2 AGP" rev 0x00
vgafb0 at pci0 dev 16 function 0 "NVIDIA GeForce FX 5200 Ultra" rev 0xa1
vgafb0: aperture needed
wsdisplay0 at vgafb0 mux 1: console (std, vt100 emulation)
ht0 at mainbus0: u3-ht, 8 devices
pci1 at ht0 bus 0
hpb0 at pci1 dev 1 function 0 "AMD 8131 PCIX" rev 0x12: 3 sources
pci2 at hpb0 bus 6
hpb1 at pci1 dev 2 function 0 "AMD 8131 PCIX" rev 0x12: 3 sources
pci3 at hpb1 bus 7
hpb2 at pci1 dev 3 function 0 "Apple U3" rev 0x00: 85 sources
pci4 at hpb2 bus 1
macobio0 at pci4 dev 7 function 0 "Apple K2 Macio" rev 0x60
openpic0 at macobio0 offset 0x40000: version 0x4614 feature 770302 LE
macgpio0 at macobio0 offset 0x50
"pmu-interrupt" at macgpio0 offset 0x9 not configured
"programmer-switch" at macgpio0 offset 0x11 not configured
"modem-reset" at macgpio0 offset 0x1d not configured
"modem-power" at macgpio0 offset 0x1e not configured
"chip-fault" at macgpio0 offset 0x1c not configured
"fcu-interrupt" at macgpio0 offset 0x15 not configured
"fcu-hw-reset" at macgpio0 offset 0x3a not configured
"slewing-done" at macgpio0 offset 0x23 not configured
"codec-input-data-mux" at macgpio0 offset 0xb not configured
"line-input-detect" at macgpio0 offset 0xc not configured
"codec-error-irq" at macgpio0 offset 0xd not configured
"dig-hw-reset" at macgpio0 offset 0x14 not configured
"line-output-detect" at macgpio0 offset 0x16 not configured
"headphone-detect" at macgpio0 offset 0x17 not configured
"codec-irq" at macgpio0 offset 0x18 not configured
"headphone-mute" at macgpio0 offset 0x1f not configured
"amp-mute" at macgpio0 offset 0x20 not configured
"hw-reset" at macgpio0 offset 0x24 not configured
"line-output-mute" at macgpio0 offset 0x25 not configured
"codec-clock-mux" at macgpio0 offset 0x26 not configured
"escc-legacy" at macobio0 offset 0x12000 not configured
zs0 at macobio0 offset 0x13000: irq 22,23
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
"i2c" at macobio0 offset 0x18000 not configured
"i2s" at macobio0 offset 0x10000 not configured
"timer" at macobio0 offset 0x15000 not configured
adb0 at macobio0 offset 0x16000
"fans" at macobio0 offset 0x4c not configured
ohci0 at pci4 dev 8 function 0 "Apple K2 USB" rev 0x00: irq 27, version 1.0,
legacy support
ohci1 at pci4 dev 9 function 0 "Apple K2 USB" rev 0x00: irq 28, version 1.0,
legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 configuration 1 interface 0 "Apple OHCI root hub" rev 1.00/1.00
addr 1
usb1 at ohci1: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "Apple OHCI root hub" rev 1.00/1.00
addr 1
ppb0 at pci1 dev 4 function 0 "Apple U3" rev 0x00
pci5 at ppb0 bus 2
"Broadcom BCM4306" rev 0x03 at pci5 dev 1 function 0 not configured
ohci2 at pci5 dev 11 function 0 "NEC USB" rev 0x43: irq 63, version 1.0
ohci3 at pci5 dev 11 function 1 "NEC USB" rev 0x43: irq 63, version 1.0
ehci0 at pci5 dev 11 function 2 "NEC USB" rev 0x04: irq 63
usb2 at ehci0: USB revision 2.0
uhub2 at usb2 configuration 1 interface 0 "NEC EHCI root hub" rev 2.00/1.00
addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "NEC OHCI root hub" rev 1.00/1.00
addr 1
usb4 at ohci3: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "NEC OHCI root hub" rev 1.00/1.00
addr 1
ppb1 at pci1 dev 5 function 0 "Apple U3" rev 0x00
pci6 at ppb1 bus 3
kauaiata0 at pci6 dev 13 function 0 "Apple K2 ATA" rev 0x00
wdc0 at kauaiata0 irq 39: DMA
atapiscsi0 at wdc0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4163B, A102> removable
cd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
"Apple K2 Firewire" rev 0x00 at pci6 dev 14 function 0 not configured
ppb2 at pci1 dev 6 function 0 "Apple U3" rev 0x00
pci7 at ppb2 bus 4
gem0 at pci7 dev 15 function 0 "Apple K2 GMAC" rev 0x00: irq 41, address
00:0d:93:b1:db:9e
brgphy0 at gem0 phy 1: BCM54K2 10/100/1000baseT PHY, rev. 0
ppb3 at pci1 dev 7 function 0 "Apple U3" rev 0x00
pci8 at ppb3 bus 5
pciide0 at pci8 dev 12 function 0 "ServerWorks K2 SATA" rev 0x00: DMA
pciide0: using irq 0 for native-PCI interrupt
pciide0: port 0: 1.5Gb/s
pciide0: port 1: 1.5Gb/s
pciide0: port 2: PHY offline
pciide0: port 3: PHY offline
uhidev0 at uhub3 port 3 configuration 1 interface 0 "vendor 0x05ac product
0x1000" rev 2.00/15.86 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub3 port 3 configuration 1 interface 1 "vendor 0x05ac product
0x1000" rev 2.00/15.86 addr 2
uhidev1: iclass 3/1
uhid0 at uhidev1: input=3, output=0, feature=1
uhidev2 at uhub4 port 2 configuration 1 interface 0 "Razer Razer BlackWidow
Ultimate" rev 2.00/2.00 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2
wskbd1 at ukbd1: console keyboard, using wsdisplay0
uhidev3 at uhub4 port 2 configuration 1 interface 1 "Razer Razer BlackWidow
Ultimate" rev 2.00/2.00 addr 2
uhidev3: iclass 3/0, 5 report ids
ukbd2 at uhidev3 reportid 1
wskbd2 at ukbd2 mux 1
wskbd2: connecting to wsdisplay0
uhid1 at uhidev3 reportid 2: input=15, output=0, feature=0
uhid2 at uhidev3 reportid 3: input=15, output=0, feature=0
uhid3 at uhidev3 reportid 4: input=15, output=0, feature=0
uhid4 at uhidev3 reportid 5: input=15, output=0, feature=0
uhidev4 at uhub4 port 2 configuration 1 interface 2 "Razer Razer BlackWidow
Ultimate" rev 2.00/2.00 addr 2
uhidev4: iclass 3/0
uhid5 at uhidev4: input=8, output=0, feature=90
softraid0 at root
scsibus1 at softraid0: 256 targets
bootpath: /ht/pci@5/ata-6/disk@0:/7.0/macppc/bsd.rd
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
