You need to hit [c](configure) several time before getting the generate. On Fri, Feb 10, 2017 at 2:33 PM, Scott Wittenburg < [email protected]> wrote:
> Also for paraviewweb, don't forget: > > PARAVIEW_ENABLE_PYTHON=ON > > Cheers, > > Scott > > On Fri, Feb 10, 2017 at 2:31 PM, Scott Wittenburg < > [email protected]> wrote: > >> I would think you'd want to build with: >> >> PARAVIEW_BUILD_QT_GUI=OFF >> >> Hope this helps, >> >> Scott >> >> On Fri, Feb 10, 2017 at 2:25 PM, Faraz Hussain <[email protected]> >> wrote: >> >>> Thanks for your help in installing Paraview on a raspberry pi. I >>> followed the steps in: >>> >>> http://www.paraview.org/Wiki/ParaView:Build_And_Install >>> >>> However, when I configure ccmake it says QT is needed. I could not >>> figure out if I can ignore that. The "generate" command did not come up. >>> >>> On a side note, it took me a while to find ccmake. I thought it was >>> installed with cmake, but seems I had to install it separately using "sudo >>> apt-get install cmake-curses-gui" . Perhaps the instructions should be >>> updated to reflect this to avoid confusion. >>> >>> >>> Quoting Sebastien Jourdain <[email protected]>: >>> >>> Wow, >>>> >>>> I'm not an expert on raspberry pi but it should be possible. >>>> BUT, (and it is a big but) you need some graphics capability for >>>> ParaView >>>> or good CPUs if you don't have a GPU. >>>> Or the rendering will be really slow. >>>> >>>> The quicker test you can do, is to build ParaView (without Qt) and try >>>> to >>>> run Visualizer with that ParaView in the command line to see what >>>> performance you are getting. If that's reasonable, then all the network >>>> setup should be "trivial". >>>> >>>> ParaView: http://www.paraview.org/Wiki/ParaView:Build_And_Install >>>> Visualizer: https://kitware.github.io/visualizer/ >>>> >>>> Good luck, >>>> >>>> Seb >>>> >>>> On Wed, Feb 8, 2017 at 8:15 AM, Faraz Hussain <[email protected]> >>>> wrote: >>>> >>>> I want to be able to manipulate vtk file on my raspberry pi via a web >>>>> browser anywhere in the world. I believe I need to install paraviewweb >>>>> and >>>>> do some reconfiguration of apache and the virtual hosts? >>>>> Unfortunately, I >>>>> am not a guru of Linux. So before I attempt it all, is it even >>>>> possible to >>>>> do this on a raspberry pi? I am using raspian . >>>>> >>>>> _______________________________________________ >>>>> Powered by www.kitware.com >>>>> >>>>> Visit other Kitware open-source projects at >>>>> http://www.kitware.com/opensou >>>>> rce/opensource.html >>>>> >>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>> http://paraview.org/Wiki/ParaView >>>>> >>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>> >>>>> Follow this link to subscribe/unsubscribe: >>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>> >>>>> >>> >>> >>> _______________________________________________ >>> Powered by www.kitware.com >>> >>> Visit other Kitware open-source projects at >>> http://www.kitware.com/opensource/opensource.html >>> >>> Please keep messages on-topic and check the ParaView Wiki at: >>> http://paraview.org/Wiki/ParaView >>> >>> Search the list archives at: http://markmail.org/search/?q=ParaView >>> >>> Follow this link to subscribe/unsubscribe: >>> http://public.kitware.com/mailman/listinfo/paraview >>> >> >> >
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
