Also for paraviewweb, don't forget: PARAVIEW_ENABLE_PYTHON=ON
Cheers, Scott On Fri, Feb 10, 2017 at 2:31 PM, Scott Wittenburg < [email protected]> wrote: > I would think you'd want to build with: > > PARAVIEW_BUILD_QT_GUI=OFF > > Hope this helps, > > Scott > > On Fri, Feb 10, 2017 at 2:25 PM, Faraz Hussain <[email protected]> > wrote: > >> Thanks for your help in installing Paraview on a raspberry pi. I followed >> the steps in: >> >> http://www.paraview.org/Wiki/ParaView:Build_And_Install >> >> However, when I configure ccmake it says QT is needed. I could not figure >> out if I can ignore that. The "generate" command did not come up. >> >> On a side note, it took me a while to find ccmake. I thought it was >> installed with cmake, but seems I had to install it separately using "sudo >> apt-get install cmake-curses-gui" . Perhaps the instructions should be >> updated to reflect this to avoid confusion. >> >> >> Quoting Sebastien Jourdain <[email protected]>: >> >> Wow, >>> >>> I'm not an expert on raspberry pi but it should be possible. >>> BUT, (and it is a big but) you need some graphics capability for ParaView >>> or good CPUs if you don't have a GPU. >>> Or the rendering will be really slow. >>> >>> The quicker test you can do, is to build ParaView (without Qt) and try to >>> run Visualizer with that ParaView in the command line to see what >>> performance you are getting. If that's reasonable, then all the network >>> setup should be "trivial". >>> >>> ParaView: http://www.paraview.org/Wiki/ParaView:Build_And_Install >>> Visualizer: https://kitware.github.io/visualizer/ >>> >>> Good luck, >>> >>> Seb >>> >>> On Wed, Feb 8, 2017 at 8:15 AM, Faraz Hussain <[email protected]> >>> wrote: >>> >>> I want to be able to manipulate vtk file on my raspberry pi via a web >>>> browser anywhere in the world. I believe I need to install paraviewweb >>>> and >>>> do some reconfiguration of apache and the virtual hosts? Unfortunately, >>>> I >>>> am not a guru of Linux. So before I attempt it all, is it even possible >>>> to >>>> do this on a raspberry pi? I am using raspian . >>>> >>>> _______________________________________________ >>>> Powered by www.kitware.com >>>> >>>> Visit other Kitware open-source projects at >>>> http://www.kitware.com/opensou >>>> rce/opensource.html >>>> >>>> Please keep messages on-topic and check the ParaView Wiki at: >>>> http://paraview.org/Wiki/ParaView >>>> >>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>> >>>> Follow this link to subscribe/unsubscribe: >>>> http://public.kitware.com/mailman/listinfo/paraview >>>> >>>> >> >> >> _______________________________________________ >> Powered by www.kitware.com >> >> Visit other Kitware open-source projects at >> http://www.kitware.com/opensource/opensource.html >> >> Please keep messages on-topic and check the ParaView Wiki at: >> http://paraview.org/Wiki/ParaView >> >> Search the list archives at: http://markmail.org/search/?q=ParaView >> >> Follow this link to subscribe/unsubscribe: >> http://public.kitware.com/mailman/listinfo/paraview >> > >
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
