It builds oke now, but its doesn't boot on my device. i don't get to see any (informative) boot error's (see log).
John Crispin schreef op 15-2-2015 om 22:16: > > > On 15/02/2015 21:44, Michaël Zweers wrote: >> >> Hello, >> >> I got a error message (kernel compile log included) when building v3.18 >> for wr703n. >> >> If you need additional info let me know. >> >> > > please retry, i just pushed a fix >
********************************************* * U-Boot 1.1.4MGZ MOD_V1 (Jun 24 2014) * ********************************************* AP121 (AR9331) U-Boot for TL-WR703N DRAM: 32 MB DDR 16-bit FLASH: Winbond W25Q128 (16 MB) CLOCKS: 400/400/200/33 MHz (CPU/RAM/AHB/SPI) LED on during eth initialization... ## Error: MDIO_BUSY! Hit any key to stop autobooting: 0 Booting image at: 0x9F020000 Image name: OpenWrt r44459 Image type: MIPS Linux Kernel Image (lzma compressed) Data size: 1205904 Bytes = 1.2 MB Load address: 0x80060000 Entry point: 0x80060000 Uncompressing kernel image... OK! Starting kernel... [ 0.000000] Linux version 3.18.7 (user@HartOfGold) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44457) ) #1 Mon Feb 16 00:49:34 CET 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 28324K/32768K available (2627K kernel code, 131K rwdata, 544K rodata, 208K init, 193K bss, 4444K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is TP-LINK TL-WR703N v1 [ 0.380000] Switched to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.400000] TCP: reno registered [ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] NET: Registered protocol family 1 [ 0.420000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.450000] msgmni has been set to 55 [ 0.450000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART [ 0.480000] console [ttyATH0] enabled [ 0.480000] console [ttyATH0] enabled [ 0.490000] bootconsole [early0] disabled [ 0.490000] bootconsole [early0] disabled [ 0.500000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.500000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.510000] 5 tp-link partitions found on MTD device spi0.0 [ 0.510000] Creating 5 MTD partitions on "spi0.0": [ 0.520000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x000000146890 : "kernel" [ 0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.540000] 0x000000146890-0x000000ff0000 : "rootfs" [ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.560000] mtd: device 2 (rootfs) set to be root filesystem [ 0.560000] 1 squashfs-split partitions found on MTD device rootfs [ 0.570000] 0x000000400000-0x000000ff0000 : "rootfs_data" [ 0.580000] 0x000000ff0000-0x000001000000 : "art" [ 0.580000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.620000] libphy: ag71xx_mdio: probed [ 1.220000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.230000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 1.230000] TCP: cubic registered [ 1.230000] NET: Registered protocol family 17 [ 1.240000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.250000] Bridge firewalling registered [ 1.250000] 8021q: 802.1Q VLAN Support v1.8 [ 1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.280000] Freeing unused kernel memory: 208K (8039c000 - 803d0000) procd: Console is alive procd: - watchdog - [ 3.690000] usbcore: registered new interface driver usbfs [ 3.700000] usbcore: registered new interface driver hub [ 3.700000] usbcore: registered new device driver usb [ 3.710000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.720000] ehci-platform: EHCI generic platform driver [ 3.720000] ehci-platform ehci-platform: EHCI Host Controller [ 3.730000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 3.740000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 3.760000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 3.760000] hub 1-0:1.0: USB hub found [ 3.760000] hub 1-0:1.0: 1 port detected [ 3.770000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.780000] ohci-platform: OHCI generic platform driver procd: - preinit - procd: Failed to start preinit procd: - early - procd: - watchdog - procd: - ubus - [ 6.120000] random: ubusd urandom read with 10 bits of entropy available procd: - init - Please press Enter to activate this console. procd: - init complete - [ 81.930000] random: nonblocking pool is initialized Failed to execute Please press Enter to activate this console. Failed to execute Please press Enter Please press EnterPlease press Enter to activate this console.
signature.asc
Description: OpenPGP digital signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
