Here is dmesg also: http://pastebin.com/ZHXdd3PK
Note: [ 12.580000] gpio-keys gpio-keys.0: unable to claim gpio 6, err=-16 [ 12.660000] gpio-keys: probe of gpio-keys.0 failed with error -16 [ 12.900000] leds-gpio: probe of leds-gpio failed with error -16 I also have trouble with sysupgrade. I can load a new firmware image using TFTP to the bootloader, but if I try a OpenWrt->OpenWrt upgrade using sysupgrade, the system never reboots and gets stuck in the bootloader when I powercycle. I can then flash the same image using TFTP and it works (so I think the image is OK, but some issue with sysupgrade). On Thu, Jun 5, 2014 at 1:12 PM, Catalin Patulea <c...@vv.carleton.ca> wrote: > Hi, > > I've got a WRT54GS v1.0 and trying to run r41004 on it. I'm having > trouble with assignment of GPIOs. > > The model number on the case, serial no, MAC and FCC ID all match a > WRT54GS v1.0 according to: > https://wikidevi.com/wiki/Linksys_WRT54GS_v1.0 > > But my nvram has these board parameters: > boardtype=0x0101 > boardnum=42 > boardrev=0x10 > (full nvram dump: http://pastebin.com/FVkddFSi) > > which in arch/mips/bcm47xx/board.c gets mapped to: > {{BCM47XX_BOARD_LINKSYS_WRT54G, "Linksys WRT54G/GS/GL"}, "0x0101", > "42", "0x10"}, > > with these LED definitions: > bcm47xx_leds_linksys_wrt54gsv1[] __initconst = { > BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF), > BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON), > BCM47XX_GPIO_LED(5, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF), > BCM47XX_GPIO_LED(7, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF), > }; > > I have DMZ and power LEDs, but they're on different GPIOs, and I don't > have a WPS LED (front panel looks like this: > http://www.rootdir.de/linksys_wrt54gs/wrt54gs_rev1.1_5.jpg). > > I did some experimentation and this is my GPIO layout: > GPIOs 0-15, ssb_chipco_gpio: > gpio-0 (sysfs ) out hi WLAN LED active high > gpio-1 (sysfs ) out lo PWR LED 0=blink 1=on > gpio-2 (adm_eecs ) in lo > gpio-3 (adm_eesk ) in lo > gpio-4 (sysfs ) in hi > gpio-5 (adm_eedi ) in lo > gpio-6 (adm_eerc ) in hi RESET BTN active low > gpio-7 (sysfs ) in hi DMZ LED active low > gpio-8 (sysfs ) in lo > gpio-9 (sysfs ) in lo > gpio-10 (sysfs ) in lo > gpio-11 (sysfs ) in lo > gpio-12 (sysfs ) in lo > gpio-13 (sysfs ) in lo > gpio-14 (sysfs ) in lo > gpio-15 (sysfs ) in lo > > which most closely matches WRTSL54GS (except no WPS LED). > > The ADM pins also might be wrong (despite definitions in the nvram > that point to those pins). My switch gets detected but when I do > "swconfig switch0 show" my system reboots. > > It feels like I have a WRT54GS v1.0 hardware with WRT54G NVRAM. Does > anyone have a WRT54GS v1.0 nvram dump to compare? WRTSL54GS dump would > also be nice. > > Catalin _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
