This adds support for the Allnet ALL6000 board to the Kernel. See http://www.allnet.de/entwicklungsplatformen.html?&L=0
Signed-off-by: Daniel Golle <dgo...@allnet.de>
diff --git a/target/linux/kirkwood/patches-3.3/300-all6000.patch
b/target/linux/kirkwood/patches-3.3/300-all6000.patch
new file mode 100644
index 0000000..571e301
--- /dev/null
+++ b/target/linux/kirkwood/patches-3.3/300-all6000.patch
@@ -0,0 +1,201 @@
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -148,6 +148,11 @@ config MACH_NSA310
+ Say 'Y' here if you want your kernel to support the
+ ZyXEL NSA-310 board.
+
++config MACH_ALL6000
++ bool "Allnet ALL6000"
++ help
++ Say 'Y' here if you want your kernel to support the
++ Allnet ALL6000 board.
+ endmenu
+
+ endif
+--- a/arch/arm/mach-kirkwood/Makefile
++++ b/arch/arm/mach-kirkwood/Makefile
+@@ -21,5 +21,6 @@ obj-$(CONFIG_MACH_NET5BIG_V2) += netxbi
+ obj-$(CONFIG_MACH_T5325) += t5325-setup.o
+ obj-$(CONFIG_MACH_NAS6210) += nas6210-setup.o
+ obj-$(CONFIG_MACH_NSA310) += nsa-310-setup.o
++obj-$(CONFIG_MACH_ALL6000) += all6000-setup.o
+
+ obj-$(CONFIG_CPU_IDLE) += cpuidle.o
+--- /dev/null
++++ b/arch/arm/mach-kirkwood/all6000-setup.c
+@@ -0,0 +1,175 @@
++/*
++ * arch/arm/mach-kirkwood/all6000-setup.c
++ *
++ * ALL6000 Board Setup
++ *
++ * Copyright (C) 2012 Daniel Golle <dgo...@allnet.de>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2. This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/version.h>
++#include <linux/platform_device.h>
++#include <linux/mtd/nand.h>
++#include <linux/mtd/partitions.h>
++#include <linux/ata_platform.h>
++#include <linux/mv643xx_eth.h>
++#include <linux/i2c.h>
++#include <linux/gpio.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <mach/kirkwood.h>
++#include <plat/mvsdio.h>
++#include "common.h"
++#include "mpp.h"
++
++/* for the PCIe reset workaround */
++#include <plat/pcie.h>
++
++static struct mtd_partition all6000_nand_parts[] = {
++ {
++ .name = "uboot",
++ .offset = 0,
++ .size = 0x80000,
++ .mask_flags = MTD_WRITEABLE
++ }, {
++ .name = "uboot-env",
++ .offset = 0x80000,
++ .size = 0x20000,
++ }, {
++ .name = "ubi0",
++ .offset = 0x100000,
++ .size = MTDPART_SIZ_FULL
++ },
++};
++
++/* PHY addresses from u-boot mii info */
++static struct mv643xx_eth_platform_data all6000_ge00_data = {
++ .phy_addr = MV643XX_ETH_PHY_ADDR(11),
++};
++
++static struct mv643xx_eth_platform_data all6000_ge01_data = {
++ .phy_addr = MV643XX_ETH_PHY_ADDR(8),
++};
++
++static struct mv_sata_platform_data all6000_sata_data = {
++ .n_ports = 2,
++};
++
++static struct mvsdio_platform_data all6000_mvsdio_data = {
++ .gpio_card_detect = 28,
++ .gpio_write_protect = 38, /* microSD => n.c.? */
++};
++
++static unsigned int all6000_mpp_config[] __initdata = {
++ MPP0_NF_IO2,
++ MPP1_NF_IO3,
++ MPP2_NF_IO4,
++ MPP3_NF_IO5,
++ MPP4_NF_IO6,
++ MPP5_NF_IO7,
++ MPP6_SYSRST_OUTn,
++ MPP8_TW0_SDA,
++ MPP9_TW0_SCK,
++ MPP10_UART0_TXD,
++ MPP11_UART0_RXD,
++ MPP12_SD_CLK,
++ MPP13_SD_CMD,
++ MPP14_SD_D0,
++ MPP15_SD_D1,
++ MPP16_SD_D2,
++ MPP17_SD_D3,
++ MPP18_NF_IO0,
++ MPP19_NF_IO1,
++ MPP20_GE1_TXD0,
++ MPP21_GE1_TXD1,
++ MPP22_GE1_TXD2,
++ MPP23_GE1_TXD3,
++ MPP24_GE1_RXD0,
++ MPP25_GE1_RXD1,
++ MPP26_GE1_RXD2,
++ MPP27_GE1_RXD3,
++ MPP28_GPIO, /* SD Status */
++ MPP29_GPIO, /* USB Power Enable */
++ MPP30_GE1_RXCTL,
++ MPP31_GE1_RXCLK,
++ MPP32_GE1_TCLKOUT,
++ MPP33_GE1_TXCTL,
++ MPP34_SATA1_ACTn,
++ MPP35_SATA0_ACTn,
++ MPP36_AU_SPDIFI,
++ MPP37_AU_SPDIFO,
++ MPP38_GPIO, /* SD Sw Wp */
++ MPP39_TDM_SPI_CS0,
++ MPP40_TDM_SPI_SCK,
++ MPP41_TDM_SPI_MISO,
++ MPP42_TDM_SPI_MOSI,
++ MPP43_TDM_CODEC_INTn,
++ MPP44_TDM_CODEC_RSTn,
++ MPP45_TDM_PCLK,
++// MPP46_TDM_FS
++ MPP46_GPIO, /* HDD PWR CTRL */
++// MPP47_TDM_DRX
++ MPP47_GPIO, /* FAN PWR CTRL */
++ MPP48_TDM_DTX,
++ MPP49_GPIO, /* USB FLAGA */
++ 0
++};
++
++
++static struct i2c_board_info __initdata all6000_i2c_info[] = {
++ {
++ I2C_BOARD_INFO("ALL6000", 0x0e),
++ },
++};
++
++static int __init all6000_pci_init(void)
++{
++ orion_pcie_reset((void __iomem *)PCIE_VIRT_BASE);
++ kirkwood_pcie_init(KW_PCIE0);
++ return 0;
++};
++subsys_initcall(all6000_pci_init);
++
++static void __init all6000_init(void)
++{
++ kirkwood_init();
++ kirkwood_mpp_conf(all6000_mpp_config);
++
++ kirkwood_uart0_init();
++ kirkwood_nand_init(ARRAY_AND_SIZE(all6000_nand_parts), 25);
++ kirkwood_sdio_init(&all6000_mvsdio_data);
++
++ if (gpio_request(29, "USB Power Enable") != 0 ||
++ gpio_direction_output(29, 1) != 0)
++ printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
++
++ kirkwood_ehci_init();
++ kirkwood_ge00_init(&all6000_ge00_data);
++ kirkwood_ge01_init(&all6000_ge01_data);
++
++ kirkwood_sata_init(&all6000_sata_data);
++
++ i2c_register_board_info(0, all6000_i2c_info,
++ ARRAY_SIZE(all6000_i2c_info));
++
++ kirkwood_i2c_init();
++
++}
++
++MACHINE_START(NAXY1200, "Allnet ALL6000")
++ /* Maintainer: Daniel Golle <dgo...@allnet.de> */
++ .atag_offset = 0x100,
++ .init_machine = all6000_init,
++ .map_io = kirkwood_map_io,
++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39)
++ .init_early = kirkwood_init_early,
++#endif
++ .init_irq = kirkwood_init_irq,
++ .timer = &kirkwood_timer,
++ .restart = kirkwood_restart,
++MACHINE_END
pgpqhPDaE7pNm.pgp
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
