sorry , in answer to my own question, UKC>disable acpi fixes
that problem .. I boot right up
So I guess the real question becomes why didn't my cd work? I
enabled aac in both GENERIC and RAMDISK_CD and did a release ..
It's fairly obvious the GENERIC worked, based on the pxe boot
working using the kernel.
Should I start from scratch? delete the release directory and
do it again?
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Behalf Of
Morris, Roy
Sent: Thursday, November 27, 2008 1:49 PM
To: Marco Peereboom
Cc: misc@openbsd.org
Subject: Re: AAC 4.4
neat, I did the pxe boot, it appears to see the 3Di now according
to the boot message, however hangs forever at ..
"piixpm0 at pci0 dev 15 function 0 "ServerWorks CSB5" rev 0x93:
SMIiic0 at piixpm0
I haven't seen that before? ... neat!
-----Original Message-----
From: Marco Peereboom [mailto:[EMAIL PROTECTED]
Sent: Thursday, November 27, 2008 11:08 AM
To: Morris, Roy
Cc: misc@openbsd.org
Subject: Re: AAC 4.4
You must have done it wrong. Did you make a release cd?
Try booting a bsd.rd over pxe with aac enabled. This has to work.
On Thu, Nov 27, 2008 at 10:20:52AM -0500, Morris, Roy wrote:
-----Original Message-----
From: Marco Peereboom [mailto:[EMAIL PROTECTED]
Sent: Wednesday, November 26, 2008 6:35 PM
To: Morris, Roy
Cc: misc@openbsd.org
Subject: Re: AAC 4.4
Show me a dmesg.
On Wed, Nov 26, 2008 at 03:21:35PM -0500, Morris, Roy wrote:
I wanted to update this for the archives. Enabling these lines in
the kernel does NOT allow 4.4 to see the Perc 3DI controller. The
3.5-stable release that was on the box (off net) worked fine.
I did a complete release of 4.4 with the lines enabled (uncommented)
and even tried UKC, but alas it's a no go. Hope this saves someone
some time down the road.
Cheers
Roy
On Tue, Nov 25, 2008 at 02:17:12PM -0500, Morris, Roy wrote:
Hi, I have a need to run the adaptec 3Di, it's not really a
choice at
this
point. I have
been doing some research in the archives and I think I need to
complile
my
4.4
kernel
with the following two lines uncommented. Any chance someone can
comment
if
this
sounds right?
#aac* at pci? # Adaptec FSA RAID controllers
#scsibus* at aac?
Cheers
Roy
Sure, here you go! As I said I have even tried the UKC> enable aac*
OpenBSD 4.4-stable (RAMDISK_CD) #0: Wed Nov 26 09:23:49 EST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/
RAMDISK_CD
cpu0: Intel(R) Pentium(R) III CPU - S 1133MHz ("GenuineIntel" 686-
class)
1.13 GHz
cpu0:
FPU,
V86,
DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,F
XSR,SSE
real mem = 2146926592 (2047MB)
avail mem = 2069417984 (1973MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/08/03, BIOS32 rev. 0 @
0xffe90,
SMBIOS rev. 2.3 @ 0xfb1e0 (47 entries)
bios0: vendor Dell Computer Corporation version "A11" date 10/08/2003
bios0: Dell Computer Corporation PowerEdge 1650
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC SPCR
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (PCI1)
acpiprt2 at acpi0: bus 2 (ZION)
acpiprt3 at acpi0: bus 3 (PCI2)
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000 0xc9000/0x4000!
0xec000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20HE Host" rev 0x23
pci1 at pchb0 bus 1
em0 at pci1 dev 2 function 0 "Intel PRO/1000XT (82544EI)" rev 0x02:
irq 7,
address 00:0f:1f:69:cc:7e
em1 at pci1 dev 4 function 0 "Intel PRO/1000XT (82544EI)" rev 0x02:
irq 5,
address 00:0f:1f:69:cc:7f
ppb0 at pci1 dev 8 function 0 "Intel 80303 IOP" rev 0x01
pci2 at ppb0 bus 2
"Adaptec AIC-7899F" rev 0x01 at pci2 dev 6 function 0 not configured
"Adaptec AIC-7899F" rev 0x01 at pci2 dev 6 function 1 not configured
"Dell PERC 3/Di" rev 0x01 at pci1 dev 8 function 1 not configured
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20HE Host" rev 0x01
pchb2 at pci0 dev 0 function 2 "ServerWorks CNB20HE Host" rev 0x01
pchb3 at pci0 dev 0 function 3 "ServerWorks CNB20HE Host" rev 0x01
pci3 at pchb3 bus 3
vga1 at pci0 dev 12 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pchb4 at pci0 dev 15 function 0 "ServerWorks CSB5" rev 0x93
pciide0 at pci0 dev 15 function 1 "ServerWorks CSB5 IDE" rev 0x93:
DMA
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-224E, K.9A> ATAPI 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev
0x05: irq
11, version 1.0, legacy support
pcib0 at pci0 dev 15 function 3 "ServerWorks CSB5 LPC" rev 0x00
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "ServerWorks OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ff4d netmask ffed ttymask ffff
rd0: fixed, 3800 blocks
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
