neat, I did the pxe boot, it appears to see the 3Di now according to the boot message, however hangs forever at ..
"piixpm0 at pci0 dev 15 function 0 "ServerWorks CSB5" rev 0x93: SMIiic0 at piixpm0 I haven't seen that before? ... neat! -----Original Message----- From: Marco Peereboom [mailto:[EMAIL PROTECTED] Sent: Thursday, November 27, 2008 11:08 AM To: Morris, Roy Cc: misc@openbsd.org Subject: Re: AAC 4.4 You must have done it wrong. Did you make a release cd? Try booting a bsd.rd over pxe with aac enabled. This has to work. On Thu, Nov 27, 2008 at 10:20:52AM -0500, Morris, Roy wrote: > -----Original Message----- > From: Marco Peereboom [mailto:[EMAIL PROTECTED] > Sent: Wednesday, November 26, 2008 6:35 PM > To: Morris, Roy > Cc: misc@openbsd.org > Subject: Re: AAC 4.4 > > > Show me a dmesg. > > On Wed, Nov 26, 2008 at 03:21:35PM -0500, Morris, Roy wrote: > > I wanted to update this for the archives. Enabling these lines in > > the kernel does NOT allow 4.4 to see the Perc 3DI controller. The > > 3.5-stable release that was on the box (off net) worked fine. > > > > I did a complete release of 4.4 with the lines enabled (uncommented) > > and even tried UKC, but alas it's a no go. Hope this saves someone > > some time down the road. > > > > Cheers > > Roy > > > > > > > > On Tue, Nov 25, 2008 at 02:17:12PM -0500, Morris, Roy wrote: > > > Hi, I have a need to run the adaptec 3Di, it's not really a choice at this > > > point. I have > > > been doing some research in the archives and I think I need to complile my > > 4.4 > > > kernel > > > with the following two lines uncommented. Any chance someone can comment if > > > this > > > sounds right? > > > > > > #aac* at pci? # Adaptec FSA RAID controllers > > > #scsibus* at aac? > > > > > > > > > Cheers > > > Roy > > > > Sure, here you go! As I said I have even tried the UKC> enable aac* > > OpenBSD 4.4-stable (RAMDISK_CD) #0: Wed Nov 26 09:23:49 EST 2008 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD > cpu0: Intel(R) Pentium(R) III CPU - S 1133MHz ("GenuineIntel" 686-class) 1.13 GHz > cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,F XSR,SSE > real mem = 2146926592 (2047MB) > avail mem = 2069417984 (1973MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 10/08/03, BIOS32 rev. 0 @ 0xffe90, SMBIOS rev. 2.3 @ 0xfb1e0 (47 entries) > bios0: vendor Dell Computer Corporation version "A11" date 10/08/2003 > bios0: Dell Computer Corporation PowerEdge 1650 > acpi0 at bios0: rev 0 > acpi0: tables DSDT FACP APIC SPCR > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 1 (PCI1) > acpiprt2 at acpi0: bus 2 (ZION) > acpiprt3 at acpi0: bus 3 (PCI2) > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000 0xc9000/0x4000! 0xec000/0x4000! > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20HE Host" rev 0x23 > pci1 at pchb0 bus 1 > em0 at pci1 dev 2 function 0 "Intel PRO/1000XT (82544EI)" rev 0x02: irq 7, address 00:0f:1f:69:cc:7e > em1 at pci1 dev 4 function 0 "Intel PRO/1000XT (82544EI)" rev 0x02: irq 5, address 00:0f:1f:69:cc:7f > ppb0 at pci1 dev 8 function 0 "Intel 80303 IOP" rev 0x01 > pci2 at ppb0 bus 2 > "Adaptec AIC-7899F" rev 0x01 at pci2 dev 6 function 0 not configured > "Adaptec AIC-7899F" rev 0x01 at pci2 dev 6 function 1 not configured > "Dell PERC 3/Di" rev 0x01 at pci1 dev 8 function 1 not configured > pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20HE Host" rev 0x01 > pchb2 at pci0 dev 0 function 2 "ServerWorks CNB20HE Host" rev 0x01 > pchb3 at pci0 dev 0 function 3 "ServerWorks CNB20HE Host" rev 0x01 > pci3 at pchb3 bus 3 > vga1 at pci0 dev 12 function 0 "ATI Rage XL" rev 0x27 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > pchb4 at pci0 dev 15 function 0 "ServerWorks CSB5" rev 0x93 > pciide0 at pci0 dev 15 function 1 "ServerWorks CSB5 IDE" rev 0x93: DMA > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus0 at atapiscsi0: 2 targets, initiator 7 > cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-224E, K.9A> ATAPI 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 > ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x05: irq 11, version 1.0, legacy support > pcib0 at pci0 dev 15 function 3 "ServerWorks CSB5 LPC" rev 0x00 > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 "ServerWorks OHCI root hub" rev 1.00/1.00 addr 1 > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec > biomask ff4d netmask ffed ttymask ffff > rd0: fixed, 3800 blocks > softraid0 at root > root on rd0a swap on rd0b dump on rd0b
