Hi! On Thu, Feb 14, 2008 at 11:29 PM, Jacob Meuser <[EMAIL PROTECTED]> wrote: > > Hi > > I got an acomdata DVEXXU2FE enclosure, and stuffed it with SONY, DVD > > RW DRU-510A. > > Attempts to burn dvds fail after about 140Mb, drive simply stops and > > becomes ready. cdrecord > > fails after some timeout, and an unknown error code is displayed. Do I > > get another enclosure, > > or did I just picked a bad unit? Any feedback is greately appreciated. > I have the same burner.
In an enclosure? > > cd0 at scsibus0 targ 1 lun 0: <SONY, DVD RW DRU-510A, 1.0d> SCSI0 > > 5/cdrom removable > although 1.0c firmware. I actually had this unit for long time, connected as an IDE, never had any problems with it. I'm putting it in an enclosure because it started to overheat inside the case with that new hardware I got recently. > your cdrecord session seems to have gotten lost. oh, I meant dmesg that covers the time frame when a dvd was attempted to be burned. Well, lemme waste another blank or two.... > maybe try using lower write speeds? my drive doesn't seem to be reliably > capable of it's advertised speeds. never had problem writing with that unit at top speed as IDE.... Well, here is the cdrecord dvd, at speed#1, no better. Failed after 27Mb. Thanks! Pawel. [EMAIL PROTECTED]/iso# nice -18 cdrecord.dvd -dev=/dev/rcd0c:0,1,0 -speed 1 -eject -v -fs=250M /home/vps/iso/80days.iso cdrecord.dvd: No write mode specified. cdrecord.dvd: Asuming -sao mode. cdrecord.dvd: If your drive does not accept -sao, try -tao. cdrecord.dvd: Future versions of cdrecord may have different drive dependent defaults. Cdrecord-ProDVD-ProBD-Clone 2.01.01a32 (i386-unknown-openbsd4.2) Copyright (C) 1995-2007 Jbrg Schilling TOC Type: 1 = CD-ROM scsidev: '/dev/rcd0c:0,1,0' devname: '/dev/rcd0c' scsibus: 0 target: 1 lun: 0 Using libscg version 'schily-0.9'. SCSI buffer size: 61440 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'SONY ' Identifikation : 'DVD RW DRU-510A ' Revision : '1.0d' Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM. Current: DVD-R sequential recording Profile: DVD+R Profile: DVD+RW Profile: DVD-RW sequential recording Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording (current) Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-2 DVD-R/DVD-RW/DVD-RAM driver (mmc_dvd). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 4718592 = 4608 KB Drive pbuf size: 8126464 = 7936 KB FIFO size : 262144000 = 256000 KB Track 01: data 4436 MB Total size: 4436 MB = 2271669 sectors Current Secsize: 2048 Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 26827 Starting to write CD/DVD/BD at speed 1 in real SAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is ON. Turning BURN-Free off Starting new track at sector: 0 Track 01: 27 of 4436 MB written (fifo 100%) [buf 100%] 1.0x.cdrecord.dvd: Input/output error. write_g1: scsi sendcmd: fatal error CDB: 2A 00 00 00 36 7E 00 00 1E 00 resid: 61440 cmd finished after 209.986s timeout 100s write track data: error after 28569600 bytes cdrecord.dvd: A write error occured. cdrecord.dvd: Please properly read the error message above. cdrecord.dvd: Input/output error. test unit ready: scsi sendcmd: fatal error CDB: 00 00 00 00 00 00 cmd finished after 0.005s timeout 100s Writing time: 330.030s Average write speed 10.2x. Min drive buffer fill was 99% Fixating... cdrecord.dvd: Input/output error. flush cache: scsi sendcmd: fatal error CDB: 35 00 00 00 00 00 00 00 00 00 cmd finished after 0.010s timeout 1000s Trouble flushing the cache cdrecord.dvd: Cannot fixate disk. Fixating time: 0.010s cdrecord.dvd: fifo had 4730 puts and 466 gets. cdrecord.dvd: fifo was 0 times empty and 374 times full, min fill was 98%.
