Marco,
With your question in mind, I more closely examined the BIOSs.

The tape drive is on channel B.  I have examined the system BIOS and found that
channel B is configured as SCSI, as indicated below:
Integrated Devices ->
        Embedded RAID Controller..........RAID Enabled
                Channel A........................RAID
                Channel B........................SCSI

I examined the PERC BIOS and found that channel B was set for 320M.  I changed
that to Ultra-2, to better match the specs that I read on the tape drive.

The tape drive is still not detected.

Thanks for your previous reply, and I would appreciate your further suggestions,
comments, or guidance.

-Victor


At 07:11 PM 5/24/2006, you wrote:
>There is no tape in your dmesg.  Are you sure the server is set to RAID/SCSI in
>the bios?
>
>On Wed, May 24, 2006 at 07:03:39PM -0700, Victor wrote:
>> Hi!
>> OpenBSD 3.8-release installation is not detecting the Dell installed
>> PV100T internal tape drive connected to the onboard SCSI on my 2850
>> PowerEdge rackmount server.  The 2850 is
>> configured as follows:
>> 2.8GHz/2MB Cache, Xeon, 800MHzFront Side Bus for PowerEdge 2850 285282 [
>> 222-0123]
>> 2.8GHz/2MB Cache, Xeon, 800MHzFront Side Bus, 2nd processor for PowerEdg
>> e 2850 2P282 [311-5387]
>> 1GB DDR2 400MHz (2X512MB) Single Ranked DIMMs 1G2D4S [311-3586]
>> Riser,ROMB,PCI-X,PE2850 ROMBPCX [320-3977]
>> 73GB,U320,SCSI,1IN 10K,PE2850 73G103 [341-1305]
>> 73GB,U320,SCSI,1IN 10K,PE2850 73G103 [341-1305]
>> MR1, ROMB RAID 1, Drives attached to PERC4ei,PE2850 MR1 [341-1354]
>> Embedded RAID - PERC4 Embedded Integrated FROMB [463-7995]
>> PV100T DAT72 w/onboard SCSI for PE2850 DAT72NC [341-1371]
>> 1x6 Hard Drive Backplane PE2850 1X6BKPL [311-4282]
>> 1.44MB Floppy Drive FD [341-1308]
>> No Operating System, Microsoft NOOSM [420-4077]
>> Dual On-Board NICS ONLY OBNICS [430-8991]
>> 24X IDE CD-RW/DVD ROM Drive for PowerEdge Servers All OS CDRWDVD [313-26
>> 92]
>> Redundant Power Supply With Y-CORD and Straight Cords PE2850 RPSWY [310-
>> 5461]
>> 
>> With OpenBSD 3.8-release installed, without X, the dmesg is:
>> OpenBSD 3.8 (GENERIC.MP) #298: Sat Sep 10 15:51:54 MDT 2005
>>     [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
>> cpu0: Intel(R) Xeon(TM) CPU 2.80GHz ("GenuineIntel" 686-class) 2.80 GHz
>> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,
>> PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
>> real mem  = 1073065984 (1047916K)
>> avail mem = 972488704 (949696K)
>> using 4278 buffers containing 53755904 bytes (52496K) of memory
>> mainbus0 (root)
>> bios0 at mainbus0: AT/286+(00) BIOS, date 09/22/05, BIOS32 rev. 0 @ 0xff
>> e90
>> pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
>> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfb4b0/320 (18 entries)
>> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801EB/ER LPC" rev 0
>> x00)
>> pcibios0: PCI bus #11 is the last bus
>> bios0: ROM list: 0xc0000/0xb000! 0xcb000/0x1000 0xcc000/0x1000 0xcd000/0
>> x2200 0xec000/0x4000!
>> mainbus0: Intel MP Specification (Version 1.4) (DELL     PE 016D     )
>> cpu0 at mainbus0: apid 0 (boot processor)
>> cpu0: apic clock running at 199 MHz
>> cpu1 at mainbus0: apid 6 (application processor)
>> cpu1: Intel(R) Xeon(TM) CPU 2.80GHz ("GenuineIntel" 686-class) 2.80 GHz
>> cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,
>> PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
>> mainbus0: bus 0 is type PCI
>> mainbus0: bus 1 is type PCI
>> mainbus0: bus 2 is type PCI
>> mainbus0: bus 3 is type PCI
>> mainbus0: bus 4 is type PCI
>> mainbus0: bus 5 is type PCI
>> mainbus0: bus 6 is type PCI
>> mainbus0: bus 7 is type PCI
>> mainbus0: bus 8 is type PCI
>> mainbus0: bus 9 is type PCI
>> mainbus0: bus 10 is type PCI
>> mainbus0: bus 11 is type PCI
>> mainbus0: bus 12 is type ISA
>> ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
>> ioapic0: misconfigured as apic 0, remapped to apic 8
>> ioapic1 at mainbus0: apid 9 pa 0xfec80000, version 20, 24 pins
>> ioapic1: misconfigured as apic 0, remapped to apic 9
>> ioapic2 at mainbus0: apid 10 pa 0xfec83000, version 20, 24 pins
>> ioapic2: misconfigured as apic 0, remapped to apic 10
>> ioapic3 at mainbus0: apid 11 pa 0xfec84000, version 20, 24 pins
>> ioapic3: misconfigured as apic 0, remapped to apic 11
>> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
>> pchb0 at pci0 dev 0 function 0 "Intel E7710 SMCH" rev 0x09
>> ppb0 at pci0 dev 2 function 0 "Intel E7710 MCH PCIE" rev 0x09
>> pci1 at ppb0 bus 1
>> ppb1 at pci1 dev 0 function 0 "Intel IOP331 Channel 0" rev 0x06
>> pci2 at ppb1 bus 2
>> ami0 at pci2 dev 14 function 0 "Dell PERC 4e/Di" rev 0x06: apic 9 int 14
>>  (irq 7) Dell 16d/32b
>> ami0: FW 521S, BIOS vH430, 256MB RAM
>> ami0: 2 channels, 0 FC loops, 1 logical drives
>> scsibus0 at ami0: 40 targets
>> sd0 at scsibus0 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/direct fix
>> ed
>> sd0: 69880MB, 8908 cyl, 255 head, 63 sec, 512 bytes/sec, 143114240 sec t
>> otal
>> scsibus1 at ami0: 16 targets
>> safte0 at scsibus1 targ 6 lun 0: <PE/PV, 1x6 SCSI BP, 1.0> SCSI2 3/proce
>> ssor fixed
>> scsibus2 at ami0: 16 targets
>> ppb2 at pci1 dev 0 function 2 "Intel IOP331 Channel 1" rev 0x06
>> pci3 at ppb2 bus 3
>> ppb3 at pci0 dev 4 function 0 "Intel E7710 MCH PCIE" rev 0x09
>> pci4 at ppb3 bus 4
>> ppb4 at pci0 dev 5 function 0 "Intel E7710 MCH PCIE" rev 0x09
>> pci5 at ppb4 bus 5
>> ppb5 at pci5 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
>> pci6 at ppb5 bus 6
>> em0 at pci6 dev 7 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: apic
>>  10 int 0 (irq 11), address: 00:14:22:1c:30:14
>> ppb6 at pci5 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09
>> pci7 at ppb6 bus 7
>> em1 at pci7 dev 8 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: apic
>>  10 int 1 (irq 3), address: 00:14:22:1c:30:15
>> ppb7 at pci0 dev 6 function 0 "Intel E7710 MCH PCIE" rev 0x09
>> pci8 at ppb7 bus 8
>> ppb8 at pci8 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09
>> pci9 at ppb8 bus 9
>> ppb9 at pci8 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09
>> pci10 at ppb9 bus 10
>> uhci0 at pci0 dev 29 function 0 "Intel 82801EB/ER USB" rev 0x02: apic 8
>> int 16 (irq 11)
>> usb0 at uhci0: USB revision 1.0
>> uhub0 at usb0
>> uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
>> uhub0: 2 ports with 2 removable, self powered
>> uhci1 at pci0 dev 29 function 1 "Intel 82801EB/ER USB" rev 0x02: apic 8
>> int 19 (irq 10)
>> usb1 at uhci1: USB revision 1.0
>> uhub1 at usb1
>> uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
>> uhub1: 2 ports with 2 removable, self powered
>> uhci2 at pci0 dev 29 function 2 "Intel 82801EB/ER USB" rev 0x02: apic 8
>> int 18 (irq 7)
>> usb2 at uhci2: USB revision 1.0
>> uhub2 at usb2
>> uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
>> uhub2: 2 ports with 2 removable, self powered
>> ehci0 at pci0 dev 29 function 7 "Intel 82801EB/ER USB" rev 0x02: apic 8
>> int 23 (irq 5)
>> usb3 at ehci0: USB revision 2.0
>> uhub3 at usb3
>> uhub3: Intel EHCI root hub, rev 2.00/1.00, addr 1
>> uhub3: 6 ports with 6 removable, self powered
>> ppb10 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xc2
>> pci11 at ppb10 bus 11
>> vga1 at pci11 dev 13 function 0 "ATI Radeon VE QY" rev 0x00
>> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
>> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
>> ichpcib0 at pci0 dev 31 function 0 "Intel 82801EB/ER LPC" rev 0x02
>> pciide0 at pci0 dev 31 function 1 "Intel 82801EB/ER IDE" rev 0x02: DMA,
>> channel 0 configured to compatibility, channel 1 configured to compatibi
>> lity
>> atapiscsi0 at pciide0 channel 0 drive 0
>> scsibus3 at atapiscsi0: 2 targets
>> cd0 at scsibus3 targ 0 lun 0: <HL-DT-ST, CDRW/DVD GCC4244, B101> SCSI0 5
>> /cdrom removable
>> cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
>> pciide0: channel 1 disabled (no drives)
>> isa0 at ichpcib0
>> isadma0 at isa0
>> pckbc0 at isa0 port 0x60/5
>> pckbd0 at pckbc0 (kbd slot)
>> pckbc0: using irq 1 for kbd slot
>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>> pms0 at pckbc0 (aux slot)
>> pckbc0: using irq 12 for aux slot
>> wsmouse0 at pms0 mux 0
>> pcppi0 at isa0 port 0x61
>> midi0 at pcppi0: <PC speaker>
>> spkr0 at pcppi0
>> sysbeep0 at pcppi0
>> npx0 at isa0 port 0xf0/16: using exception 16
>> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
>> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
>> biomask 0 netmask 0 ttymask 0
>> pctr: user-level cycle counter enabled
>> uhub4 at uhub3 port 3
>> uhub4: Dell product 0xa001, rev 2.00/0.00, addr 2
>> uhub4: 2 ports with 2 removable, self powered, multiple transaction tran
>> slators
>> dkcsum: sd0 matches BIOS drive 0x80
>> root on sd0a
>> rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
>> 
>> Just as a test, I booted using a 3.9 boot only CD made from cd39.iso,
>> exited to shell and ran dmesg. The tape drive was not listed.
>> Dell's utility successfully tested and "passed" the tape drive.
>> 
>> The tape drive is on Channel B, LUN 0, ID 6, and the tape drive's DIP
>> switches are at default, all on "1."
>> 
>> I would appreciate your suggestions or comments.
>> 
>> -Victor 

Reply via email to