Try running 'netinstall' as administrator. You have a static IP address on the interface facing the router per the wiki? https://wiki.mikrotik.com/wiki/Manual:Netinstall
I remember it being a pain getting setup for the first time back a long time ago when I first used it. I haven't used it for a few years now though. On Tue, Mar 19, 2019 at 3:29 PM Leon Zetekoff via Mikrotik-users < mikrotik-users@wispa.org> wrote: > reset button does the same as going into the setup mode and switching the > boot mode. sends out bootp but nothing responds :-( > > it's like netinstall isn't binding to the port??? > > leon > On 3/19/2019 2:51 PM, Leon Zetekoff wrote: > > forgot about the reset button thing will have to try later. No VM on this > bare metal. > > thanks I'll give it a try later leon > On 3/19/2019 2:42 PM, C D Tavares wrote: > > It can be a bear setting up netinstall to work the first time, especially > if you use a VM. Also, if you're unaware that for some reason the CCR > series runs netinstall on the last port, instead of the first port like > every other MikroTik product. > > Netinstall only works if you power up the unit while holding the reset > button down for about 20+ seconds until the blinky light goes out. If port > 8 is pulling DHCP, it's not in the correct startup state. And if it's > looking for DHCP, it's no wonder it doesn't want to talk to your laptop, as > your laptop doesn't offer any. > > On Mar 19, 2019, at 11:18 AM, Leon Zetekoff via Mikrotik-users < > mikrotik-users@wispa.org> wrote: > > Hi Joe.... > > I spent a few hours tackling Netinstall and I can not get it to work. If I > connect ether8 to the network it pulls a DHCP but if I connect ether8 to my > laptop through a cross-over cable nothing happens. I turned off AVG > protection as well as the default windows firewall. If I let the router > boot, I can ping ether8 from the laptop using the x-over cable and ether8 > set to 10Mbps. The laptop can be set to Auto OR 10M fixed. > > Netinstall never sees the bootp request and the netinstall gui only shows > disk drives. > > ANy ideas? > > Thanks leon > On 3/19/2019 11:34 AM, Joe Novak wrote: > > CCR support was added in 6.x if I'm not mistaken. The bootloader version > may have 3.09, though. > > Assuming you've netinstalled the OS... I'm not sure there is much else to > do. You can try to swap in the ram from a known good router, same with > power supply. But that is more or less the extent of troubleshooting I > think you can do. > > On Tue, Mar 19, 2019 at 10:21 AM Leon Zetekoff via Mikrotik-users < > mikrotik-users@wispa.org> wrote: > >> Hi Folks....this device was given to us a number of years ago and it had >> 3.09 on it I believe. We eventually upgraded it to 6.41.rc9 I think it >> was and started to act flooey. Put it on shelf since no time to deal >> with it. Resurrected it again and i manually upgraded it to 6.42.12. >> Whats going on is the ethernet ports only show 10Mbps, auto or anything >> other than 10M doesnt work. ALso only seems I can only talk to my >> laptop. Mikrotik (and I) believe its a hardware issue and of course out >> of warranty. >> >> Anyone else seen this before and any way to resolve it other than >> tossing it in the trash bin? >> >> Thanks leon >> >> >> --- >> This email has been checked for viruses by AVG. >> https://www.avg.com >> >> _______________________________________________ >> Mikrotik-users mailing list >> Mikrotik-users@wispa.org >> http://lists.wispa.org/mailman/listinfo/mikrotik-users >> > > > <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > Virus-free. > www.avg.com > <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > _______________________________________________ > Mikrotik-users mailing list > Mikrotik-users@wispa.org > http://lists.wispa.org/mailman/listinfo/mikrotik-users > > > _______________________________________________ > Mikrotik-users mailing list > Mikrotik-users@wispa.org > http://lists.wispa.org/mailman/listinfo/mikrotik-users >
_______________________________________________ Mikrotik-users mailing list Mikrotik-users@wispa.org http://lists.wispa.org/mailman/listinfo/mikrotik-users
