forgot about the reset button thing will have to try later. No VM on
this bare metal.
thanks I'll give it a try later leon
On 3/19/2019 2:42 PM, C D Tavares wrote:
It can be a bear setting up netinstall to work the first time,
especially if you use a VM. Also, if you're unaware that for some
reason the CCR series runs netinstall on the last port, instead of the
first port like every other MikroTik product.
Netinstall only works if you power up the unit while holding the reset
button down for about 20+ seconds until the blinky light goes out. If
port 8 is pulling DHCP, it's not in the correct startup state. And if
it's looking for DHCP, it's no wonder it doesn't want to talk to your
laptop, as your laptop doesn't offer any.
On Mar 19, 2019, at 11:18 AM, Leon Zetekoff via Mikrotik-users
<mikrotik-users@wispa.org <mailto:mikrotik-users@wispa.org>> wrote:
Hi Joe....
I spent a few hours tackling Netinstall and I can not get it to work.
If I connect ether8 to the network it pulls a DHCP but if I connect
ether8 to my laptop through a cross-over cable nothing happens. I
turned off AVG protection as well as the default windows firewall. If
I let the router boot, I can ping ether8 from the laptop using the
x-over cable and ether8 set to 10Mbps. The laptop can be set to Auto
OR 10M fixed.
Netinstall never sees the bootp request and the netinstall gui only
shows disk drives.
ANy ideas?
Thanks leon
On 3/19/2019 11:34 AM, Joe Novak wrote:
CCR support was added in 6.x if I'm not mistaken. The bootloader
version may have 3.09, though.
Assuming you've netinstalled the OS... I'm not sure there is much
else to do. You can try to swap in the ram from a known good router,
same with power supply. But that is more or less the extent of
troubleshooting I think you can do.
On Tue, Mar 19, 2019 at 10:21 AM Leon Zetekoff via Mikrotik-users
<mikrotik-users@wispa.org <mailto:mikrotik-users@wispa.org>> wrote:
Hi Folks....this device was given to us a number of years ago
and it had
3.09 on it I believe. We eventually upgraded it to 6.41.rc9 I
think it
was and started to act flooey. Put it on shelf since no time to
deal
with it. Resurrected it again and i manually upgraded it to
6.42.12.
Whats going on is the ethernet ports only show 10Mbps, auto or
anything
other than 10M doesnt work. ALso only seems I can only talk to my
laptop. Mikrotik (and I) believe its a hardware issue and of
course out
of warranty.
Anyone else seen this before and any way to resolve it other than
tossing it in the trash bin?
Thanks leon
---
This email has been checked for viruses by AVG.
https://www.avg.com <https://www.avg.com/>
_______________________________________________
Mikrotik-users mailing list
Mikrotik-users@wispa.org <mailto:Mikrotik-users@wispa.org>
http://lists.wispa.org/mailman/listinfo/mikrotik-users
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
Virus-free. www.avg.com
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
<x-msg://47/#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________
Mikrotik-users mailing list
Mikrotik-users@wispa.org <mailto:Mikrotik-users@wispa.org>
http://lists.wispa.org/mailman/listinfo/mikrotik-users
_______________________________________________
Mikrotik-users mailing list
Mikrotik-users@wispa.org
http://lists.wispa.org/mailman/listinfo/mikrotik-users
