On Thu, 2013-05-16 at 07:01 +0000, Zang Roy-R61911 wrote:
> I just tried your RCW. one e1000 card works in slot7.
> we may need to check others ...
Tried 4 and 7 ...
Note that this *used* to work. Last year I had this machine up with 2
cards doing things. Not sure what changed, it's possible that the DIP
got inadvertently changed. Or somebody stole a jumper from it in the
lab :-)
> U-Boot 2013.01-00078-g2741c99 (May 03 2013 - 00:20:41)
>
> CPU0: P5020E, Version: 2.0, (0x82280020)
> Core: E5500, Version: 1.2, (0x80240012)
> Clock Configuration:
> CPU0:2000 MHz, CPU1:2000 MHz,
> CCB:800 MHz,
> DDR:666.667 MHz (1333.333 MT/s data rate) (Asynchronous), LBC:100 MHz
> FMAN1: 600 MHz
> QMAN: 400 MHz
> PME: 400 MHz
> L1: D-cache 32 kB enabled
> I-cache 32 kB enabled
> Reset Configuration Word (RCW):
> 00000000: 0c540000 00000000 1e120000 00000000
> 00000010: d8984a01 03002000 de800000 41000000
> 00000020: 00000000 00000000 00000000 10070000
> 00000030: 00000000 00000000 00000000 00000000
My RCW is identical
> Board: P5020DS, Sys ID: 0x1c, Sys Ver: 0x02, FPGA Ver: 0x04, vBank: 4
Mine is:
Board: P5020DS, Sys ID: 0x1c, Sys Ver: 0x12, FPGA Ver: 0x05, vBank: 4
> SERDES Reference Clocks: Bank1=100Mhz Bank2=125Mhz Bank3=125Mhz
Same.
> I2C: ready
> SPI: ready
> DRAM: Initializing....using SPD
> Detected UDIMM i-DIMM
> Detected UDIMM i-DIMM
> 2 GiB left unmapped
> 4 GiB (DDR3, 64-bit, CL=9, ECC on)
> DDR Controller Interleaving Mode: cache line
> DDR Chip-Select Interleaving Mode: CS0+CS1
> Testing 0x00000000 - 0x7fffffff
> Testing 0x80000000 - 0xffffffff
> Remap DDR 2 GiB left unmapped
>
> POST memory PASSED
> Flash: 128 MiB
> L2: 512 KB enabled
> Corenet Platform Cache: 2048 KB enabled
> SRIO1: disabled
> SRIO2: disabled
> NAND: 1024 MiB
> MMC: FSL_SDHC: 0
> EEPROM: Invalid ID (ff ff ff ff)
> PCIe1: Root Complex, x2, regs @ 0xfe200000
> 01:00.0 - 8086:105e - Network controller
> 01:00.1 - 8086:105e - Network controller
> PCIe1: Bus 00 - 01
> PCIe2: disabled
> PCIe3: Root Complex, no link, regs @ 0xfe202000
> PCIe3: Bus 02 - 02
> PCIe4: disabled
And I never see anything here anymore...
> In: serial
> Out: serial
> Err: serial
> Net: Initializing Fman
> Fman1: Uploading microcode version 106.1.6
> PHY reset timed out
> PHY reset timed out
> PHY reset timed out
> PHY reset timed out
> e1000: 00:15:17:16:ce:b8
> e1000: 00:15:17:16:ce:b9
> FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4 [PRIME], FM1@DTSEC5,
> FM1@TGEC1, e1000#0
> Warning: e1000#0 MAC addresses don't match:
> Address in SROM is 00:15:17:16:ce:b8
> Address in environment is 00:1b:21:68:5e:d4
> , e1000#1
> Warning: e1000#1 using MAC address from net device
>
> =>
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
