On Fri, Aug 01, 2008 at 10:58:58AM -0500, Sparks, Sam wrote:
> I'm trying to get the compact flash up and running on an mpc8349eITX,
> and am continually running into issues where the IRQ is not processed,
> and the mmio commands are not getting response. At this point, I am
> starting to suspect a HW issue, but I was hoping to verify that I am
> using a known good kernel configuration.
>
> Has anyone successfully communicated with a compact flash device in true
> IDE mode on the MPC8349eITX? If so, do you happen to know the kernel
> configuration and/or revision?
Works like a charm here. I use quite outdated u-boot though. Which one
you use? I could try it (if it is community u-boot).
As for the backtrace you posted recently, I remeber I've noticed the
similar issue long ago on some mITX board. I believe the board had
hw issues indeed (or CF card I tested with). The problem could be in
the IRQ line itself (for some reason it always low), or it could be
IDE cmd/data lines at fault, so that IDE can't receive status read
command and does not deassert the interrupt line... quite hard to
tell.
The logs below.
(Notice that u-boot says that UPMA is configured to work with CF IDE).
U-Boot 1.2.0-g5b1313fb (Jun 9 2007 - 17:29:42) MPC83XX
CPU: e300c1, MPC8349E, Rev: 11 at 533.333 MHz, CSB: 266 MHz
Board: Freescale MPC8349E-mITX
UPMA: Configured for compact flash
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 16 MB
PCI: Bus Dev VenId DevId Class Int
00 10 1095 3114 0180 00
In: serial
Out: serial
Err: serial
Board revision: 1.0 (PCF8475A)
Net: TSEC0
IDE: Bus 0: OK
Device 0: Model: KINGSTON Firm: 20060713 Ser#: KINGSTON CF 00003E2C
Type: Hard Disk
Capacity: 495.1 MB = 0.4 GB (1014048 x 512)
MPC8349E-mITX> boot
[...]
Using MPC834x ITX machine description
Linux version 2.6.27-rc1-00006-g2799599 ([EMAIL PROTECTED]) (gcc version
4.2.0)) #35 Fri Aug 1 20:32:51 MSD 2008
[...]
scsi0 : pata_platform
ata1: PATA max PIO6 mmio cmd 0xf0000000 ctl 0xf000020c irq 23
ata1.00: ATA-0: KINGSTON, 20060713, max MWDMA2
ata1.00: 1014048 sectors, multi 0: LBA
ata1.00: configured for PIO
ata1.00: configured for PIO
ata1: EH complete
scsi 0:0:0:0: Direct-Access ATA KINGSTON 2006 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1014048 512-byte hardware sectors (519 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 1014048 512-byte hardware sectors (519 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
[...]
# dd if=/dev/sda of=/dev/null count=20000
20000+0 records in
20000+0 records out
10240000 bytes (10 MB) copied, 1.94026 seconds, 5.3 MB/s
--
Anton Vorontsov
email: [EMAIL PROTECTED]
irc://irc.freenode.net/bd2
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
