From: Girish Mahadevan <giri...@codeaurora.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0 and SPI
Mode 3. The controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <giri...@codeaurora.org>
Signed-off-by: Ryan Case <ryandc...@chromium.org>
---
Changes in v2:
- Addressed formatting feedback
- Squashed bug fixes and features from Doug
- Now uses transfer_one_message instead of mem_ops
- Fixed suspend/resume
- Added spinlocks
drivers/spi/Kconfig | 6 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-qcom-qspi.c | 608 ++++++++++++++++++++++++++++++++++++
3 files changed, 615 insertions(+)
create mode 100644 drivers/spi/spi-qcom-qspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index de03d67bcd2b..36922e12c3b0 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -549,6 +549,12 @@ config SPI_RSPI
help
SPI driver for Renesas RSPI and QSPI blocks.
+config SPI_QCOM_QSPI
+ tristate "QTI QPSPI controller"
+ depends on ARCH_QCOM
+ help
+ QSPI(Quad SPI) driver for Qualcomm QSPI controller.
+
config SPI_QUP
tristate "Qualcomm SPI controller with QUP interface"
depends on ARCH_QCOM || (ARM && COMPILE_TEST)
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 876f8690fc47..f997c49255a6 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -112,3 +112,4 @@ obj-$(CONFIG_SPI_ZYNQMP_GQSPI) +=
spi-zynqmp-gqspi.o
# SPI slave protocol handlers
obj-$(CONFIG_SPI_SLAVE_TIME) += spi-slave-time.o
obj-$(CONFIG_SPI_SLAVE_SYSTEM_CONTROL) += spi-slave-system-control.o
+obj-$(CONFIG_SPI_QCOM_QSPI) += spi-qcom-qspi.o
diff --git a/drivers/spi/spi-qcom-qspi.c b/drivers/spi/spi-qcom-qspi.c
new file mode 100644
index 000000000000..1bf2720a7b6f
--- /dev/null
+++ b/drivers/spi/spi-qcom-qspi.c
@@ -0,0 +1,608 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#include <asm/unaligned.h>
+
+#define AHB_MIN_HZ 9600000UL
+#define QSPI_NUM_CS 2
+#define QSPI_BYTES_PER_WORD 4
+#define MSTR_CONFIG 0x0000
+#define AHB_MASTER_CFG 0x0004
+#define MSTR_INT_EN 0x000C
+#define MSTR_INT_STATUS 0x0010
+#define PIO_XFER_CTRL 0x0014
+#define PIO_XFER_CFG 0x0018
+#define PIO_XFER_STATUS 0x001c
+#define PIO_DATAOUT_1B 0x0020
+#define PIO_DATAOUT_4B 0x0024
+#define RD_FIFO_CFG 0x0028
+#define RD_FIFO_STATUS 0x002c
+#define RD_FIFO_RESET 0x0030
+#define CUR_MEM_ADDR 0x0048
+#define HW_VERSION 0x004c
+#define RD_FIFO 0x0050
+#define SAMPLING_CLK_CFG 0x0090
+#define SAMPLING_CLK_STATUS 0x0094
+
+/* Macros to help set/get fields in MSTR_CONFIG register */
+#define FULL_CYCLE_MODE BIT(3)
+#define FB_CLK_EN BIT(4)
+#define PIN_HOLDN BIT(6)
+#define PIN_WPN BIT(7)
+#define DMA_ENABLE BIT(8)
+#define BIG_ENDIAN_MODE BIT(9)
+#define SPI_MODE_MSK 0xc00
+#define SPI_MODE_SHFT 10
+#define CHIP_SELECT_NUM BIT(12)
+#define SBL_EN BIT(13)
+#define LPA_BASE_MSK 0x3c000
+#define LPA_BASE_SHFT 14
+#define TX_DATA_DELAY_MSK 0xc0000
+#define TX_DATA_DELAY_SHFT 18
+#define TX_CLK_DELAY_MSK 0x300000
+#define TX_CLK_DELAY_SHFT 20
+#define TX_CS_N_DELAY_MSK 0xc00000
+#define TX_CS_N_DELAY_SHFT 22
+#define TX_DATA_OE_DELAY_MSK 0x3000000
+#define TX_DATA_OE_DELAY_SHFT 24
+
+/* Macros to help set/get fields in AHB_MSTR_CFG register */
+#define HMEM_TYPE_START_MID_TRANS_MSK 0x7
+#define HMEM_TYPE_START_MID_TRANS_SHFT 0
+#define HMEM_TYPE_LAST_TRANS_MSK 0x38
+#define HMEM_TYPE_LAST_TRANS_SHFT 3
+#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_MSK 0xc0
+#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_SHFT 6
+#define HMEMTYPE_READ_TRANS_MSK 0x700
+#define HMEMTYPE_READ_TRANS_SHFT 8
+#define HSHARED BIT(11)
+#define HINNERSHARED BIT(12)
+
+/* Macros to help set/get fields in MSTR_INT_EN/MSTR_INT_STATUS registers */
+#define RESP_FIFO_UNDERRUN BIT(0)
+#define RESP_FIFO_NOT_EMPTY BIT(1)
+#define RESP_FIFO_RDY BIT(2)
+#define HRESP_FROM_NOC_ERR BIT(3)
+#define WR_FIFO_EMPTY BIT(9)
+#define WR_FIFO_FULL BIT(10)
+#define WR_FIFO_OVERRUN BIT(11)
+#define TRANSACTION_DONE BIT(16)
+#define QSPI_ERR_IRQS (RESP_FIFO_UNDERRUN | HRESP_FROM_NOC_ERR | \
+ WR_FIFO_OVERRUN)
+#define QSPI_ALL_IRQS (QSPI_ERR_IRQS | RESP_FIFO_RDY | \
+ WR_FIFO_EMPTY | WR_FIFO_FULL | \
+ TRANSACTION_DONE)
+
+/* Macros to help set/get fields in RD_FIFO_CONFIG register */
+#define CONTINUOUS_MODE BIT(0)
+
+/* Macros to help set/get fields in RD_FIFO_RESET register */
+#define RESET_FIFO BIT(0)
+
+/* Macros to help set/get fields in PIO_TRANSFER_CONFIG register */
+#define TRANSFER_DIRECTION BIT(0)
+#define MULTI_IO_MODE_MSK 0xe
+#define MULTI_IO_MODE_SHFT 1
+#define TRANSFER_FRAGMENT BIT(8)
+
+/* Macros to help set/get fields in PIO_TRANSFER_CONTROL register */
+#define REQUEST_COUNT_MSK 0xffff
+
+/* Macros to help set/get fields in PIO_TRANSFER_STATUS register */
+#define WR_FIFO_BYTES_MSK 0xffff0000
+#define WR_FIFO_BYTES_SHFT 16
+
+/* Macros to help set/get fields in RD_FIFO_STATUS register */
+#define FIFO_EMPTY BIT(11)
+#define WR_CNTS_MSK 0x7f0
+#define WR_CNTS_SHFT 4
+#define RDY_64BYTE BIT(3)
+#define RDY_32BYTE BIT(2)
+#define RDY_16BYTE BIT(1)
+#define FIFO_RDY BIT(0)
+
+/*
+ * The Mode transfer macros, the values are programmed to the HW registers
+ * when doing PIO mode of transfers.
+ */
+#define SDR_1BIT 1
+#define SDR_2BIT 2
+#define SDR_4BIT 3
+#define DDR_1BIT 5
+#define DDR_2BIT 6
+#define DDR_4BIT 7
+
+/* The Mode transfer macros when setting up DMA descriptors */
+#define DMA_DESC_SINGLE_SPI 1
+#define DMA_DESC_DUAL_SPI 2
+#define DMA_DESC_QUAD_SPI 3
+
+enum qspi_dir {
+ QSPI_READ,
+ QSPI_WRITE,
+};
+
+struct qspi_xfer {
+ union {
+ const void *tx_buf;
+ void *rx_buf;
+ };
+ unsigned int rem_bytes;
+ int buswidth;
+ enum qspi_dir dir;
+ bool is_last;
+};
+
+enum qspi_clocks {
+ QSPI_CLK_CORE,
+ QSPI_CLK_IFACE,
+ QSPI_NUM_CLKS
+};
+
+struct qcom_qspi {
+ void __iomem *base;
+ struct device *dev;
+ struct clk_bulk_data clks[QSPI_NUM_CLKS];
+ struct qspi_xfer xfer;
+ spinlock_t lock;
+};
+
+static int qspi_buswidth_to_iomode(struct qcom_qspi *ctrl, int buswidth)
+{
+ switch (buswidth) {
+ case 1:
+ return SDR_1BIT;
+ case 2:
+ return SDR_2BIT;
+ case 4:
+ return SDR_4BIT;
+ default:
+ dev_warn_once(ctrl->dev,
+ "Unexpected bus width: %d\n", buswidth);
+ return SDR_1BIT;
+ }
+}
+
+static void qcom_qspi_pio_xfer_cfg(struct qcom_qspi *ctrl)
+{
+ u32 pio_xfer_cfg = 0;
+ struct qspi_xfer *xfer;
+
+ xfer = &ctrl->xfer;
+ pio_xfer_cfg = readl(ctrl->base + PIO_XFER_CFG);
+ pio_xfer_cfg &= ~TRANSFER_DIRECTION;
+ pio_xfer_cfg |= xfer->dir;
+ if (xfer->is_last)
+ pio_xfer_cfg &= ~TRANSFER_FRAGMENT;
+ else
+ pio_xfer_cfg |= TRANSFER_FRAGMENT;
+ pio_xfer_cfg &= ~MULTI_IO_MODE_MSK;
+ pio_xfer_cfg |= qspi_buswidth_to_iomode(ctrl, xfer->buswidth) <<
+ MULTI_IO_MODE_SHFT;
+
+ writel(pio_xfer_cfg, ctrl->base + PIO_XFER_CFG);
+}
+
+static void qcom_qspi_pio_xfer_ctrl(struct qcom_qspi *ctrl)
+{
+ u32 pio_xfer_ctrl;
+
+ pio_xfer_ctrl = readl(ctrl->base + PIO_XFER_CTRL);
+ pio_xfer_ctrl &= ~REQUEST_COUNT_MSK;
+ pio_xfer_ctrl |= ctrl->xfer.rem_bytes;
+ writel(pio_xfer_ctrl, ctrl->base + PIO_XFER_CTRL);
+}
+
+static void qcom_qspi_pio_xfer(struct qcom_qspi *ctrl)
+{
+ u32 ints;
+
+ qcom_qspi_pio_xfer_cfg(ctrl);
+
+ /* Ack any previous interrupts that might be hanging around */
+ writel(QSPI_ALL_IRQS, ctrl->base + MSTR_INT_STATUS);
+
+ /* Setup new interrupts */
+ if (ctrl->xfer.dir == QSPI_WRITE)
+ ints = QSPI_ERR_IRQS | WR_FIFO_EMPTY;
+ else
+ ints = QSPI_ERR_IRQS | RESP_FIFO_RDY;
+ writel(ints, ctrl->base + MSTR_INT_EN);
+
+ /* Kick off the transfer */
+ qcom_qspi_pio_xfer_ctrl(ctrl);
+}
+
+static void qcom_qspi_handle_err(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+ unsigned long flags;
+
+ spin_lock_irqsave(&ctrl->lock, flags);
+ writel(0, ctrl->base + MSTR_INT_EN);
+ ctrl->xfer.rem_bytes = 0;
+ spin_unlock_irqrestore(&ctrl->lock, flags);
+}
+
+static int qcom_qspi_transfer_one(struct spi_master *master,
+ struct spi_device *slv,
+ struct spi_transfer *xfer)
+{
+ struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+ int ret;
+ unsigned long speed_hz;
+ unsigned long flags;
+
+ speed_hz = slv->max_speed_hz;
+ if (xfer->speed_hz)
+ speed_hz = xfer->speed_hz;
+
+ ret = clk_set_rate(ctrl->clks[QSPI_CLK_CORE].clk, speed_hz * 4);
+ if (ret) {
+ dev_err(ctrl->dev, "Failed to set core clk %d\n", ret);
+ return ret;
+ }
+
+ spin_lock_irqsave(&ctrl->lock, flags);
+
+ /* We are half duplex, so either rx or tx will be set */
+ if (xfer->rx_buf) {
+ ctrl->xfer.dir = QSPI_READ;
+ ctrl->xfer.buswidth = xfer->rx_nbits;
+ ctrl->xfer.rx_buf = xfer->rx_buf;
+ } else {
+ ctrl->xfer.dir = QSPI_WRITE;
+ ctrl->xfer.buswidth = xfer->tx_nbits;
+ ctrl->xfer.tx_buf = xfer->tx_buf;
+ }
+ ctrl->xfer.is_last = list_is_last(&xfer->transfer_list,
+ &master->cur_msg->transfers);
+ ctrl->xfer.rem_bytes = xfer->len;
+ qcom_qspi_pio_xfer(ctrl);
+
+ spin_unlock_irqrestore(&ctrl->lock, flags);
+
+ /* We'll call spi_finalize_current_transfer() when done */
+ return 1;
+}
+
+static int qcom_qspi_setup(struct spi_device *spi)
+{
+ u32 mstr_cfg;
+ struct qcom_qspi *ctrl;
+ int tx_data_oe_delay = 1;
+ int tx_data_delay = 1;
+ int ret;
+
+ ctrl = spi_master_get_devdata(spi->master);
+ ret = pm_runtime_get_sync(ctrl->dev);
+ if (ret) {
+ dev_err(ctrl->dev, "Runtime PM get failed in setup: %d\n", ret);
+ pm_runtime_put(ctrl->dev);
+ return ret;
+ }
+
+ mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
+ mstr_cfg &= ~CHIP_SELECT_NUM;
+ if (spi->chip_select)
+ mstr_cfg |= CHIP_SELECT_NUM;
+
+ mstr_cfg = (mstr_cfg & ~SPI_MODE_MSK) | (spi->mode << SPI_MODE_SHFT);
+ mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE;
+ mstr_cfg |= (mstr_cfg & ~TX_DATA_OE_DELAY_MSK) |
+ (tx_data_oe_delay << TX_DATA_OE_DELAY_SHFT);
+ mstr_cfg |= (mstr_cfg & ~TX_DATA_DELAY_MSK) |
+ (tx_data_delay << TX_DATA_DELAY_SHFT);
+ mstr_cfg &= ~DMA_ENABLE;
+
+ writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
+
+ /*
+ * Ensure that the configuration goes through by reading back
+ * a register from the IO space.
+ */
+ mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
+
+ pm_runtime_put(ctrl->dev);
+
+ return 0;
+}
+
+static irqreturn_t pio_read(struct qcom_qspi *ctrl)
+{
+ u32 rd_fifo_status;
+ u32 rd_fifo;
+ unsigned int wr_cnts;
+ unsigned int bytes_to_read;
+ unsigned int words_to_read;
+ u32 *word_buf;
+ u8 *byte_buf;
+ int i;
+
+ rd_fifo_status = readl(ctrl->base + RD_FIFO_STATUS);
+
+ if (!(rd_fifo_status & FIFO_RDY)) {
+ dev_dbg(ctrl->dev, "Spurious IRQ %#x\n", rd_fifo_status);
+ return IRQ_NONE;
+ }
+
+ wr_cnts = (rd_fifo_status & WR_CNTS_MSK) >> WR_CNTS_SHFT;
+
+ if (wr_cnts > ctrl->xfer.rem_bytes)
+ wr_cnts = ctrl->xfer.rem_bytes;
+
+ words_to_read = wr_cnts / QSPI_BYTES_PER_WORD;
+ bytes_to_read = wr_cnts % QSPI_BYTES_PER_WORD;
+
+ if (words_to_read) {
+ word_buf = ctrl->xfer.rx_buf;
+ ctrl->xfer.rem_bytes -= words_to_read * QSPI_BYTES_PER_WORD;
+ for (i = 0; i < words_to_read; i++) {
+ rd_fifo = readl(ctrl->base + RD_FIFO);
+ put_unaligned(rd_fifo, word_buf++);
+ }
+ ctrl->xfer.rx_buf = word_buf;
+ }
+
+ if (bytes_to_read) {
+ byte_buf = ctrl->xfer.rx_buf;
+ rd_fifo = readl(ctrl->base + RD_FIFO);
+ ctrl->xfer.rem_bytes -= bytes_to_read;
+ for (i = 0; i < bytes_to_read; i++)
+ *byte_buf++ = rd_fifo >> (i * BITS_PER_BYTE);
+ ctrl->xfer.rx_buf = byte_buf;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t pio_write(struct qcom_qspi *ctrl)
+{
+ const void *xfer_buf = ctrl->xfer.tx_buf;
+ const int *word_buf;
+ const char *byte_buf;
+ unsigned int wr_fifo_bytes;
+ unsigned int wr_fifo_words;
+ unsigned int wr_size;
+ unsigned int rem_words;
+
+ wr_fifo_bytes = readl(ctrl->base + PIO_XFER_STATUS)
+ >> WR_FIFO_BYTES_SHFT;
+
+ if (ctrl->xfer.rem_bytes < QSPI_BYTES_PER_WORD) {
+ /* Process the last 1-3 bytes */
+ wr_size = min(wr_fifo_bytes, ctrl->xfer.rem_bytes);
+ ctrl->xfer.rem_bytes -= wr_size;
+
+ byte_buf = xfer_buf;
+ while (wr_size--)
+ writel(*byte_buf++,
+ ctrl->base + PIO_DATAOUT_1B);
+ ctrl->xfer.tx_buf = byte_buf;
+ } else {
+ /*
+ * Process all the whole words; to keep things simple we'll
+ * just wait for the next interrupt to handle the last 1-3
+ * bytes if we don't have an even number of words.
+ */
+ rem_words = ctrl->xfer.rem_bytes / QSPI_BYTES_PER_WORD;
+ wr_fifo_words = wr_fifo_bytes / QSPI_BYTES_PER_WORD;
+
+ wr_size = min(rem_words, wr_fifo_words);
+ ctrl->xfer.rem_bytes -= wr_size * QSPI_BYTES_PER_WORD;
+
+ word_buf = xfer_buf;
+ while (wr_size--)
+ writel(get_unaligned(word_buf++),
+ ctrl->base + PIO_DATAOUT_4B);
+ ctrl->xfer.tx_buf = word_buf;
+
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t qcom_qspi_irq(int irq, void *dev_id)
+{
+ u32 int_status;
+ struct qcom_qspi *ctrl = dev_id;
+ irqreturn_t ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ctrl->lock, flags);
+
+ int_status = readl(ctrl->base + MSTR_INT_STATUS);
+ writel(int_status, ctrl->base + MSTR_INT_STATUS);
+
+ if (ctrl->xfer.dir == QSPI_WRITE) {
+ if (int_status & WR_FIFO_EMPTY)
+ ret = pio_write(ctrl);
+ } else {
+ if (int_status & RESP_FIFO_RDY)
+ ret = pio_read(ctrl);
+ }
+
+ if (!ctrl->xfer.rem_bytes) {
+ writel(0, ctrl->base + MSTR_INT_EN);
+ spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
+ }
+
+ spin_unlock_irqrestore(&ctrl->lock, flags);
+ return ret;
+}
+
+static int qcom_qspi_probe(struct platform_device *pdev)
+{
+ int ret = 0;
+ struct device *dev;
+ struct resource *res;
+ struct spi_master *master;
+ struct qcom_qspi *ctrl;
+
+ dev = &pdev->dev;
+
+ master = spi_alloc_master(dev, sizeof(struct qcom_qspi));
+ if (!master) {
+ dev_err(dev, "Failed to alloc spi master\n");
+ return -ENOMEM;
+ }
+ platform_set_drvdata(pdev, master);
+
+ ctrl = spi_master_get_devdata(master);
+
+ spin_lock_init(&ctrl->lock);
+ ctrl->dev = dev;
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ctrl->base = devm_ioremap(dev, res->start, resource_size(res));
+ if (IS_ERR(ctrl->base)) {
+ ret = PTR_ERR(ctrl->base);
+ dev_err(dev, "Failed to get base addr %d\n", ret);
+ goto exit_probe_master_put;
+ }
+
+ ctrl->clks[QSPI_CLK_CORE].id = "core";
+ ctrl->clks[QSPI_CLK_IFACE].id = "iface";
+ ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks);
+ if (ret)
+ goto exit_probe_master_put;
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0) {
+ dev_err(dev, "Failed to get irq %d\n", ret);
+ goto exit_probe_master_put;
+ }
+ ret = devm_request_irq(dev, ret, qcom_qspi_irq,
+ IRQF_TRIGGER_HIGH, dev_name(dev), ctrl);
+ if (ret) {
+ dev_err(dev, "Failed to request irq %d\n", ret);
+ goto exit_probe_master_put;
+ }
+
+ master->max_speed_hz = 300000000;
+ master->num_chipselect = QSPI_NUM_CS;
+ master->bus_num = pdev->id;
+ master->dev.of_node = pdev->dev.of_node;
+ master->mode_bits = SPI_MODE_0 |
+ SPI_TX_DUAL | SPI_RX_DUAL |
+ SPI_TX_QUAD | SPI_RX_QUAD;
+ master->flags = SPI_MASTER_HALF_DUPLEX;
+ master->setup = qcom_qspi_setup;
+ master->transfer_one = qcom_qspi_transfer_one;
+ master->handle_err = qcom_qspi_handle_err;
+ master->auto_runtime_pm = true;
+
+ pm_runtime_enable(dev);
+
+ ret = spi_register_master(master);
+ if (ret)
+ goto exit_probe_runtime_disable;
+
+ return 0;
+
+exit_probe_runtime_disable:
+ pm_runtime_disable(dev);
+
+exit_probe_master_put:
+ spi_master_put(master);
+
+ return ret;
+}
+
+static int qcom_qspi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+
+ /* Unregister _before_ disabling pm_runtime() so we stop transfers */
+ spi_unregister_master(master);
+
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+static int __maybe_unused qcom_qspi_runtime_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+
+ clk_bulk_disable_unprepare(QSPI_NUM_CLKS, ctrl->clks);
+
+ return 0;
+}
+
+static int __maybe_unused qcom_qspi_runtime_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+
+ return clk_bulk_prepare_enable(QSPI_NUM_CLKS, ctrl->clks);
+}
+
+static int qcom_qspi_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ int ret;
+
+ ret = spi_master_suspend(master);
+ if (ret)
+ return ret;
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ spi_master_resume(master);
+
+ return ret;
+}
+
+static int qcom_qspi_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ ret = spi_master_resume(master);
+ if (ret)
+ pm_runtime_force_suspend(dev);
+
+ return ret;
+}
+
+static const struct dev_pm_ops qcom_qspi_dev_pm_ops = {
+ SET_RUNTIME_PM_OPS(qcom_qspi_runtime_suspend,
+ qcom_qspi_runtime_resume, NULL)
+ SET_SYSTEM_SLEEP_PM_OPS(qcom_qspi_suspend, qcom_qspi_resume)
+};
+
+static const struct of_device_id qcom_qspi_dt_match[] = {
+ { .compatible = "qcom,sdm845-qspi", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_qspi_dt_match);
+
+static struct platform_driver qcom_qspi_driver = {
+ .driver = {
+ .name = "qcom_qspi",
+ .pm = &qcom_qspi_dev_pm_ops,
+ .of_match_table = qcom_qspi_dt_match,
+ },
+ .probe = qcom_qspi_probe,
+ .remove = qcom_qspi_remove,
+};
+module_platform_driver(qcom_qspi_driver);
+
+MODULE_DESCRIPTION("SPI driver for QSPI cores");
+MODULE_LICENSE("GPL v2");
--
2.19.0.444.g18242da7ef-goog
