Oh wait, I do. The whole box already says “(not supported in Legacy graphics)”.
So we could remove the “not in legacy” disclaimer for Mac, and reverse the checkbox sense for non-Mac (so it would say something like “Hide crosshairs for selection tool” or something). > On 7 Feb 2018, at 20:56, Jeff Young <j...@rokeby.ie> wrote: > > Well, except on OSX, where the legacy canvas didn’t support it. > > So turning on the checkbox isn’t supported in Mac-legacy, while turning off > the checkbox isn’t supported in other-legacy. > > I haven’t the foggiest idea how to communicate that succinctly. > > > > >> On 7 Feb 2018, at 20:39, Wayne Stambaugh <stambau...@gmail.com >> <mailto:stambau...@gmail.com>> wrote: >> >> The crosshair behavior is canvas dependent. In the legacy canvas, the >> crosshairs (full screen or small) are always shown. In the modern >> canvases, the crosshairs are only show when a tool is active and the >> option is disabled. Enabling the option makes the modern canvas >> behavior the same as the legacy canvas. >> >> On 2/7/2018 3:37 PM, Jeff Young wrote: >>> Oh wait, bells are ringing. >>> >>> The disclaimer on the checkbox is OSX-only. Other platforms support it >>> even in legacy, don’t they? >>> >>> >>> >>>> On 7 Feb 2018, at 20:28, Wayne Stambaugh <stambau...@gmail.com >>>> <mailto:stambau...@gmail.com>> wrote: >>>> >>>> I just looked and there is no mention of legacy or modern in the >>>> checkbox string. There is a "not supported in legacy graphics" note in >>>> the grid options but not the crosshair setting. >>>> >>>> On 2/7/2018 2:24 PM, Jeff Young wrote: >>>>> We already did. Well: “Always display crosshairs (not in Legacy)”, >>>>> anyway. >>>>> >>>>> >>>>>> On 7 Feb 2018, at 19:21, Wayne Stambaugh <stambau...@gmail.com >>>>>> <mailto:stambau...@gmail.com>> wrote: >>>>>> >>>>>> On 2/7/2018 1:54 PM, jp charras wrote: >>>>>>> Le 07/02/2018 à 19:44, Wayne Stambaugh a écrit : >>>>>>>> If you are using a gal canvas, the only time you see the cross hairs is >>>>>>>> when a tool is selected. This is true of even the small cross hairs. >>>>>>> >>>>>>> Yes, but if in Preferences/Display Options you enable "Always display >>>>>>> crosshairs" you should have >>>>>>> the crosshair cursor always displayed. >>>>>> >>>>>> So that's what that option is for! We really should change the text to >>>>>> is "Always display crosshairs in modern canvas" since this has no effect >>>>>> on the legacy canvas. >>>>>> >>>>>>> >>>>>>>> >>>>>>>> On 2/7/2018 1:41 PM, Bernhard Stegmaier wrote: >>>>>>>>> Yes, did see the button (synced today). >>>>>>>>> But it didn’t seem to change anything. >>>>>>>>> Where should I see it? >>>>>>>>> >>>>>>>>>> On 7. Feb 2018, at 19:39, Jeff Young <j...@rokeby.ie >>>>>>>>>> <mailto:j...@rokeby.ie>> wrote: >>>>>>>>>> >>>>>>>>>> The crosshairs should be available again in a current build. Do you >>>>>>>>>> see the toolbar button on the left? >>>>>>>>>> >>>>>>>>>>> On 7 Feb 2018, at 17:36, Bernhard Stegmaier >>>>>>>>>>> <stegma...@sw-systems.de <mailto:stegma...@sw-systems.de>> wrote: >>>>>>>>>>> >>>>>>>>>>> … yes, no good. >>>>>>>>>>> It seems to be OK when just panning around. >>>>>>>>>>> But, it gets very laggy while e.g. dragging/moving symbols around >>>>>>>>>>> (even on a not so big schematic I had at hand). >>>>>>>>>>> >>>>>>>>>>> It is fine if you take out the Refresh() quoted below on macOS. >>>>>>>>>>> I didn’t see any obvious things on a quick check with the remaining >>>>>>>>>>> changes (might be due to the fact that crosshair is still disabled >>>>>>>>>>> on macOS?). >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> Regards, >>>>>>>>>>> Bernhard >>>>>>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Mailing list: https://launchpad.net/~kicad-developers >>>>>> <https://launchpad.net/~kicad-developers> >>>>>> Post to : kicad-developers@lists.launchpad.net >>>>>> <mailto:kicad-developers@lists.launchpad.net> >>>>>> Unsubscribe : https://launchpad.net/~kicad-developers >>>>>> <https://launchpad.net/~kicad-developers> >>>>>> More help : https://help.launchpad.net/ListHelp >>>>>> <https://help.launchpad.net/ListHelp> >>>>> >>> >
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : kicad-developers@lists.launchpad.net Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
