Hi Nick. Good question. In this case first track from pad is just small stub. Teardrop point it is not good connection. Teardrop is always in first track in trace from item. It is there but too small. When you run DRC it is reported and you can fix it. Video shows.
https://youtu.be/uSUWkbdA2zM And thinking about those acid things, this property eliminates them too. Not eliminates, you can do them, but not in accidentally because they are reported as a warnings or errors, if you are using teardrops. Warning is example that teardrop is not in right size when first track is enough long to go out item, but too short that teardop can be in full set size. By locking teardrop warnings are eliminated, if you decide to keep teardrop as it is, so that warning is not disturbing you any longer. I build this property, but is it good? Regards Heikki On Tue, Apr 25, 2017 at 8:54 AM, Nick Østergaard <oe.n...@gmail.com> wrote: > Why does it seem like this one pad in the 3D view does not have a > teardrop? See attached. > > 2017-04-24 10:35 GMT+02:00 Heikki Pulkkinen <hei6m...@gmail.com>: > > Now they are there again. It was not so big job that I think. > > > > https://youtu.be/G1YCu2daNww > > > > On Thu, Mar 30, 2017 at 10:04 AM, Heikki Pulkkinen <hei6m...@gmail.com> > > wrote: > >> > >> Yes, they all where there, but any longer. > >> > >> On Wed, Mar 29, 2017 at 8:28 PM, Mário Luzeiro <mrluze...@ua.pt> wrote: > >>> > >>> Impressive! > >>> Is it rendering in the 3D-Viewer? > >>> I.e.: does it reuse existent formats (segment, zones, arcs, etc) or is > it > >>> implementing new elements? (and so it is missing in 3D-Viewer) ? > >>> > >>> > >>> ________________________________________ > >>> From: Kicad-developers > >>> <kicad-developers-bounces+mrluzeiro=ua...@lists.launchpad.net> on > behalf of > >>> Jakub Kozdon <fldriv...@seznam.cz> > >>> Sent: 29 March 2017 16:38:29 > >>> To: Heikki Pulkkinen; kicad-developers > >>> Subject: Re: [Kicad-developers] Something new and old > >>> > >>> Great work! > >>> > >>> Do you think that you can add snowman pads into your tool? [1] > >>> > >>> Hope will be soon merged! > >>> > >>> [1] http://www.ti.com/lit/an/sprabb3/sprabb3.pdf > >>> > >>> > >>> Hi, > >>> > >>> Any comments, questions! > >>> > >>> https://youtu.be/CQC6XMTGxkk > >>> > >>> Heikki > >>> > >>> > >>> > >>> _______________________________________________ > >>> Mailing list: https://launchpad.net/~kicad-developers > >>> Post to : > >>> kicad-developers@lists.launchpad.net<mailto:kicad-developers > @lists.launchpad.net> > >>> Unsubscribe : https://launchpad.net/~kicad-developers > >>> More help : https://help.launchpad.net/ListHelp > >>> > >>> > >>> > >> > > > > > > _______________________________________________ > > Mailing list: https://launchpad.net/~kicad-developers > > Post to : kicad-developers@lists.launchpad.net > > Unsubscribe : https://launchpad.net/~kicad-developers > > More help : https://help.launchpad.net/ListHelp > > >
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : kicad-developers@lists.launchpad.net Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
