Looks like you need to have a minimal SMS configuration like to define some basic Storage Group,Storclas, Data Class, Management Class. Then translate and activate...
On Thu, Oct 10, 2013 at 11:36 PM, mf db <[email protected]> wrote: > Hello, > > I have created a LDS, Its the main catalog volume where I have created this > COMMDS,ACDS,SCDS. I was able to bring up the system but when I try to use > ISMF 8.3 to alter the base configuration i get the CDS is not found though > it is very much visible via D SMS,OPTIONS and when i do SETSMS > COMMDS(SYSTEM.ZT01.COMMDS), I get the below information. > > IEE600I REPLY TO 011 IS;U > IGD056I COMMDS SYSTEM.ZT01.COMMDS NOT FOUND > > Not sure where is it exactly missing on.. > > > On Thu, Oct 10, 2013 at 2:59 AM, Lizette Koehler <[email protected] > >wrote: > > > You cannot activate an already active ACDS SCDS or COMMDS. They would > > need > > to be new to do that. > > > > You seem to have a valid ACDS and SCDS in the configuration. If I > > understand your current issue it is the COMMDS. > > > > So I have some basic questions. > > > > When it was defined, you created a Linear VSAM Dataset? > > It is on a volume that is accessible to your LPAR? > > > > When the SYSTEM IPLd, you indicated it could not use the COMMDS, but it > > could use the SCDS and ACDS? > > What happens when you issue the SETSMS COMMDS(your.data.set.name.here) > > > > Provide all messages. > > > > Is all that correct? > > > > Lizette > > > > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:[email protected]] On > > Behalf Of mf db > > Sent: Wednesday, October 09, 2013 1:42 PM > > To: [email protected] > > Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > > > Hello Lizette, > > > > I did for SETSMS for COMMDS there was no response at all, but for SCDS > and > > ACDS i got the below : > > > > setsms acds(system.zt01.acds) > > IGD068I ACDS SYSTEM.ZT01.ACDS SPECIFIED IS THE SAME AS THE ACTIVE > ACDS > > - COMMAND IS REJECTED > > > > > > setsms scds(system.zt01.scds) > > IGD056I ACDS SYSTEM.ZT01.ACDS NOT FOUND > > IGD052I REQUEST DENIED - NO ACTIVE CONFIGURATION > > > > > > On Thu, Oct 10, 2013 at 1:58 AM, Lizette Koehler > > <[email protected]>wrote: > > > > > If he did a SETSMS COMMDS(SYSTEM.ZT01.COMMDS) and it got an IGD002I > > > then something else might be incorrect. > > > > > > Could you do the SETSMS command and post all message from the > invocation? > > > > > > > > > > > > Lizette > > > > > > > > > -----Original Message----- > > > From: IBM Mainframe Discussion List [mailto:[email protected]] > > > On Behalf Of Jim Blalock > > > Sent: Wednesday, October 09, 2013 1:09 PM > > > To: [email protected] > > > Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > > > > > Is the COMMDS cataloged in the master catalog? SMS may be started > > > early enough that the usercats aren't available yet. > > > > > > On 10/9/2013 3:59 PM, mf db wrote: > > > > Lizette, > > > > > > > > Its during IPL.. but before IPL i did updated the IGDSMS00 with the > > > > new ACDS and COMMDS. During IPL it said it couldn't recognize the > > > > COMMDS, so I tried activating by SETSMS COMMDS/SETSMS ACDS/SETSMS > > > > SCDS > > > but > > > no luck. > > > > > > > > d sms,options > > > > IGD002I 15:58:40 DISPLAY SMS 613 > > > > ACDS = SYSTEM.ZT01.ACDS > > > > COMMDS = SYSTEM.ZT01.COMMDS > > > > ACDS LEVEL = UNAVAIL > > > > > > > > > > > > > > > > On Thu, Oct 10, 2013 at 12:39 AM, Lizette Koehler > > > > <[email protected]>wrote: > > > > > > > >> I would also do a D SMS,OPTIONS and check to see if the files are > > > >> recognized. > > > >> > > > >> Lizette > > > >> > > > >> > > > >> -----Original Message----- > > > >> From: IBM Mainframe Discussion List > > > >> [mailto:[email protected]] On Behalf Of Lizette Koehler > > > >> Sent: Wednesday, October 09, 2013 12:08 PM > > > >> To: [email protected] > > > >> Subject: Re: NO COMMUNICATIONS DATA SET - IGD002I > > > >> > > > >> What were you doing at the time? And IPL? A SETSMS? > > > >> > > > >> How is your IGDSMSxx member created? > > > >> > > > >> SMS ACDS(dsname) COMMDS(dsname) > > > >> > > > >> > > > >> Try a SETSMS COMMDS(xxxxx) Check my syntax. > > > >> > > > >> > > > >> > > > >> Lizette > > > >> > > > >> > > > >> -----Original Message----- > > > >> From: IBM Mainframe Discussion List > > > >> [mailto:[email protected]] On Behalf Of mf db > > > >> Sent: Wednesday, October 09, 2013 12:02 PM > > > >> To: [email protected] > > > >> Subject: NO COMMUNICATIONS DATA SET - IGD002I > > > >> > > > >> Hello Group, > > > >> > > > >> I am trying to bring up our sandbox for testing purpose, but while > > > >> Bring up the I get message as > > > >> > > > >> IGD002I : NO COMMUNICATIONS DATA SET > > > >> > > > >> Though i have defined it in IGDSMS00 and Also I did the activate of > > > >> SET SMS=xx, but still I do not get this activated during IPL. > > > >> > > > >> This is a new COMMDS,ACDS,SCDS defined but still I do not see get > > > >> clue where I missed on. > > > >> > > > >> Any suggestions or pointers ? > > > >> > > > >> Peter > > > >> > > > > > > > ---------------------------------------------------------------------- > > For IBM-MAIN subscribe / signoff / archive access instructions, > > send email to [email protected] with the message: INFO IBM-MAIN > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
