"Ask if you have any more questions, this is a good demonstration of the mosaic mode in Hugin.
A dangerous thing to say! Thanks for your instructions. I worked my way through it and saw what you had done. I started with three images, but there is a fourth, which is the foot of the stone. I can see why you fixed the centre image in the set of three and adjusted the positions of the others. What should I do with four images? On Sunday, 23 March 2025 at 08:33:29 UTC [email protected] wrote: > Hi Nick, attached a PTO project that stitches your photos. > > Since this isn't a 'normal' panorama (the camera shifts between shots), > you need to set Interface > Expert. This enables XYZ (mosaic) camera > positions. > When Hugin loads photos it initially gives them a horizontal spread, but > you don't want this, in the Photos tab right click and 'Reset positions'. > In the preview, reduce the angle of the view to fit the photos, and set > the output projection to rectilinear (the same as your input photos), > Add some control points, you don't need many, but they need a good spread > over the overlapping areas. > In the photos tab, select Optimise > Geometric > custom parameters, this > will reveal the Optimiser tab. > In the Optimiser tab, you want the middle photo to stay in place, but set > optimisation for Yaw, Pitch, Roll, X, Y & Z for the top and bottom photos. > Optimise. > The photos should now be aligned. Go back to the preview, fit the field of > view so you can see the whole output, crop and stitch. > > Ask if you have any more questions, this is a good demonstration of the > mosaic mode in Hugin. > > -- > Bruno > > On Fri, 21 Mar 2025 at 10:27, Nick Thomas wrote: > >> I found a tutorial from 2010, which walked me through stitching flat >> images. I followed it, and got better results, but with the top and bottom >> clipped off. >> >> What appears to be happening is that it is calculating the final size as >> though the images were being horizontally stacked. I rotated the images and >> followed the tutorial again. This gives me a different focal length for the >> lens, and hence a different FOV. I no longer get the clipping, but I do >> get the distortion again. >> >> On Thursday, 20 March 2025 at 10:34:24 UTC Bruno Postle wrote: >> > For a flat object viewed straight-on you need rectilinear output >>> projection. >>> >>> Five control points should be enough, but my question is, did you move >>> the camera between shots? Hugin can stitch this, but it is not a 'normal' >>> panorama, so you need to use what Hugin calls a 'mosaic' technique where >>> you optimise the camera positions. >>> >>> Can you upload the photos? I'm sure someone here can show you how it's >>> done. >>> >>> On Thu, 20 Mar 2025, 09:49 Nick Thomas wrote: >>> >>>> I am attempting to stitch images of the Dunfallandy Stone >>>> <https://i0.wp.com/sobt.co.uk/wp-content/uploads/2022/03/Dunfallandy-Stone-1.jpg?resize=768%2C1024&ssl=1>. >>>> >>>> I have three images, the top, middle and bottom of the stone taken with a >>>> Nikkor 14-24mm lens, set at 14mm. >>>> >>>> When I try to align the images, no control points are found. I have >>>> manually added 5 CP on each pair of images. >>>> >>>> The thing that I am now unsure of is what projection to use. I have >>>> tried a number (fish eye, equisolid, orthographic, amongst others), but >>>> all >>>> give me a huge amount of distortion on the final image. >>>> >>>> My questions are: >>>> >>>> 1. Are 5 CP sufficient? >>>> 2. What projection should I use for a stitch of 3 vertical images? >>>> >>>> > > -- > Bruno > -- A list of frequently asked questions is available at: http://wiki.panotools.org/Hugin_FAQ --- You received this message because you are subscribed to the Google Groups "hugin and other free panoramic software" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion visit https://groups.google.com/d/msgid/hugin-ptx/9dd81085-15ac-4ecf-a6dc-1497c58a768dn%40googlegroups.com.
