bonjour,
de notre expérience avec des vdx 6740, nous n'avons pu faire de lacp
sur du cuivre 1Gbs, la mention speed 1000 obligatoire pour faire
fonctioner le lien cuivre semble empecher le fonctionnement lacp ...
en revanche en fibre 1Gbs (ou 10Gbs) nous en avons ...
petite question grey-market subsidiaire : comment se passe le licensing
pour les ports supplementaires ou les ports 40Gbs en grey-market ?
--
Jean-Daniel Pauget http://rezopole.net/
Rezopole/LyonIX +33 (0)4 27 46 00 50
On Tue, Sep 04, 2018 at 01:44:29PM +0200, Mathieu Poussin wrote:
> Hello.
>
> Je suis en train de configurer un Brocade VDX (gray market donc pas de
> support malheureusement).
>
> Impossible de monter un LACP, en faite c'est assez bizarre, le Port-Channel
> monte bien mais impossible de no shut les membres (Qui sont des ports 10g
> mais avec des sfp copper 1g), exemple :
>
> bcn-sws-3-1# show port-channel 1
> LACP Aggregator: Po 1
> Aggregator type: Standard
> Admin Key: 0001 - Oper Key 0001
> Partner System ID - 0x0000,00-00-00-00-00-00
> Partner Oper Key 0000
> Member ports:
> Link: Te 0/35 (0x18118184) sync: 0
> Link: Te 0/40 (0x18140189) sync: 0
> Link: Te 0/55 (0x181B8284) sync: 0
> Link: Te 0/60 (0x181E0289) sync: 0
>
> bcn-sws-3-1# sh run int po 1
> interface Port-channel 1
> speed 1000
> description Uplink to BCN-SWC-3-1
> switchport
> switchport mode trunk
> switchport trunk allowed vlan add 110-112
> switchport trunk tag native-vlan
> no shutdown
> !
>
> bcn-sws-3-1(config)# int te 0/35
> bcn-sws-3-1(conf-if-te-0/35)# no shut
> bcn-sws-3-1(conf-if-te-0/35)# end
> bcn-sws-3-1# sh run int te 0/35
> interface TenGigabitEthernet 0/35
> speed 1000
> description Uplink
> channel-group 1 mode active type standard
> lacp timeout long
> shutdown # << wtf?
> !
>
>
> bcn-sws-3-1# sh int te 0/35
> TenGigabitEthernet 0/35 is admin down, line protocol is down (admin down)
> Hardware is Ethernet, address is 0005.334b.f97e
> Current address is 0005.334b.f97e
> Pluggable media not present
> Description: Uplink
> Interface index (ifindex) is 403800452
> MTU 2500 bytes
> LineSpeed Actual : Nil
> LineSpeed Configured : 1000 Mbit, Duplex: Full
> Priority Tag disable
> IPv6 RA Guard disable
> Last clearing of show interface counters: 03:39:48
> Queueing strategy: fifo
> Receive Statistics:
> 0 packets, 0 bytes
> Unicasts: 0, Multicasts: 0, Broadcasts: 0
> 64-byte pkts: 0, Over 64-byte pkts: 0, Over 127-byte pkts: 0
> Over 255-byte pkts: 0, Over 511-byte pkts: 0, Over 1023-byte pkts: 0
> Over 1518-byte pkts(Jumbo): 0
> Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0
> Errors: 0, Discards: 0
> Transmit Statistics:
> 1960 packets, 289098 bytes
> Unicasts: 8, Multicasts: 1302, Broadcasts: 650
> Underruns: 0
> Errors: 0, Discards: 0
> Rate info (interval 299 seconds):
> Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
> Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
> Time since last interface status change: 00:44:44
>
>
> Le "Pluggable media not present" me porte a confusions vu que j'ai d'autre
> ports 10g qui sont up, fonctionnent bien mais qui retournent aussi ça,
> exemple:
>
> bcn-sws-3-1# sh int te 0/1
> TenGigabitEthernet 0/1 is up, line protocol is up (connected)
> Hardware is Ethernet, address is 0005.334b.f95c
> Current address is 0005.334b.f95c
> Pluggable media not present
> Description: STORAGE
> Interface index (ifindex) is 402685952
> MTU 2500 bytes
> LineSpeed Actual : 10000 Mbit
> LineSpeed Configured : Auto, Duplex: Full
> Priority Tag disable
> IPv6 RA Guard disable
> Last clearing of show interface counters: 03:42:41
> Queueing strategy: fifo
> Receive Statistics:
> 145608 packets, 29709612 bytes
> Unicasts: 144478, Multicasts: 940, Broadcasts: 190
> 64-byte pkts: 112543, Over 64-byte pkts: 15686, Over 127-byte pkts: 2810
> Over 255-byte pkts: 730, Over 511-byte pkts: 613, Over 1023-byte pkts:
> 13226
> Over 1518-byte pkts(Jumbo): 0
> Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0
> Errors: 0, Discards: 0
> Transmit Statistics:
> 1176133 packets, 1658862747 bytes
> Unicasts: 1174922, Multicasts: 952, Broadcasts: 259
> Underruns: 0
> Errors: 0, Discards: 0
> Rate info (interval 299 seconds):
> Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
> Output 0.000708 Mbits/sec, 0 packets/sec, 0.00% of line-rate
> Time since last interface status change: 01:19:15
>
> La version (Pas de support donc pas de MAJ malheureusement...):
>
> bcn-sws-3-1# show ver
>
> Network Operating System Software
> Network Operating System Version: 4.1.1
> Copyright (c) 1995-2014 Brocade Communications Systems, Inc.
> Firmware name: 4.1.1
> Build Time: 19:48:22 Mar 19, 2014
> Install Time: 12:34:44 Mar 23, 2015
> Kernel: 2.6.34.6
>
> BootProm: 2.2.0
> Control Processor: e500v2 with 2048 MB of memory
>
> Appl Primary/Secondary Versions
> ------------------------------------------
> NOS 4.1.1
> 4.1.1
>
> Une idée?
> Pas d'accès aux forums Brocade non plus sans support alors que la réponse y
> est surement...
>
> Merci
>
>
>
> ---------------------------
> Liste de diffusion du FRnOG
> http://www.frnog.org/
---------------------------
Liste de diffusion du FRnOG
http://www.frnog.org/
