Désolé j'en mélange mes langues :) J'ai pu trouver la solution... Si on force speed a 1G ça pose des soucis... Le message est pas très explicite. https://gtacknowledge.extremenetworks.com/articles/Q_A/Setting-1GB-SFP-on-VDX-to-speed-1000-brings-link-down
Je laisse ça la si ca peut aider dans le future. Merci :) ---- On Tue, 04 Sep 2018 13:58:34 +0200 Mathieu Poussin <m...@mpouss.in> wrote ---- > Ok I just found in the logs : > > Incompatible SFP transceiver for interface TenGigabitEthernet 0/35 is > detected > > Which is weird those are supposed to be compatible with ? 1GE-XBR-000190 > > Maybe a firmware update could fix this ? (hard to say without support) Or > this is expected to not be compatible ? > > Thanks > > > ---- On Tue, 04 Sep 2018 13:44:29 +0200 Mathieu Poussin <m...@mpouss.in> > wrote ---- > > Hello. > > > > Je suis en train de configurer un Brocade VDX (gray market donc pas de > support malheureusement). > > > > Impossible de monter un LACP, en faite c'est assez bizarre, le > Port-Channel monte bien mais impossible de no shut les membres (Qui sont des > ports 10g mais avec des sfp copper 1g), exemple : > > > > bcn-sws-3-1# show port-channel 1 > > LACP Aggregator: Po 1 > > Aggregator type: Standard > > Admin Key: 0001 - Oper Key 0001 > > Partner System ID - 0x0000,00-00-00-00-00-00 > > Partner Oper Key 0000 > > Member ports: > > Link: Te 0/35 (0x18118184) sync: 0 > > Link: Te 0/40 (0x18140189) sync: 0 > > Link: Te 0/55 (0x181B8284) sync: 0 > > Link: Te 0/60 (0x181E0289) sync: 0 > > > > bcn-sws-3-1# sh run int po 1 > > interface Port-channel 1 > > speed 1000 > > description Uplink to BCN-SWC-3-1 > > switchport > > switchport mode trunk > > switchport trunk allowed vlan add 110-112 > > switchport trunk tag native-vlan > > no shutdown > > ! > > > > bcn-sws-3-1(config)# int te 0/35 > > bcn-sws-3-1(conf-if-te-0/35)# no shut > > bcn-sws-3-1(conf-if-te-0/35)# end > > bcn-sws-3-1# sh run int te 0/35 > > interface TenGigabitEthernet 0/35 > > speed 1000 > > description Uplink > > channel-group 1 mode active type standard > > lacp timeout long > > shutdown # << wtf? > > ! > > > > > > bcn-sws-3-1# sh int te 0/35 > > TenGigabitEthernet 0/35 is admin down, line protocol is down (admin down) > > > Hardware is Ethernet, address is 0005.334b.f97e > > Current address is 0005.334b.f97e > > Pluggable media not present > > Description: Uplink > > Interface index (ifindex) is 403800452 > > MTU 2500 bytes > > LineSpeed Actual : Nil > > LineSpeed Configured : 1000 Mbit, Duplex: Full > > Priority Tag disable > > IPv6 RA Guard disable > > Last clearing of show interface counters: 03:39:48 > > Queueing strategy: fifo > > Receive Statistics: > > 0 packets, 0 bytes > > Unicasts: 0, Multicasts: 0, Broadcasts: 0 > > 64-byte pkts: 0, Over 64-byte pkts: 0, Over 127-byte pkts: 0 > > Over 255-byte pkts: 0, Over 511-byte pkts: 0, Over 1023-byte pkts: 0 > > Over 1518-byte pkts(Jumbo): 0 > > Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0 > > Errors: 0, Discards: 0 > > Transmit Statistics: > > 1960 packets, 289098 bytes > > Unicasts: 8, Multicasts: 1302, Broadcasts: 650 > > Underruns: 0 > > Errors: 0, Discards: 0 > > Rate info (interval 299 seconds): > > Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate > > Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate > > Time since last interface status change: 00:44:44 > > > > > > Le "Pluggable media not present" me porte a confusions vu que j'ai > d'autre ports 10g qui sont up, fonctionnent bien mais qui retournent aussi > ça, exemple: > > > > bcn-sws-3-1# sh int te 0/1 > > TenGigabitEthernet 0/1 is up, line protocol is up (connected) > > Hardware is Ethernet, address is 0005.334b.f95c > > Current address is 0005.334b.f95c > > Pluggable media not present > > Description: STORAGE > > Interface index (ifindex) is 402685952 > > MTU 2500 bytes > > LineSpeed Actual : 10000 Mbit > > LineSpeed Configured : Auto, Duplex: Full > > Priority Tag disable > > IPv6 RA Guard disable > > Last clearing of show interface counters: 03:42:41 > > Queueing strategy: fifo > > Receive Statistics: > > 145608 packets, 29709612 bytes > > Unicasts: 144478, Multicasts: 940, Broadcasts: 190 > > 64-byte pkts: 112543, Over 64-byte pkts: 15686, Over 127-byte pkts: > 2810 > > Over 255-byte pkts: 730, Over 511-byte pkts: 613, Over 1023-byte > pkts: 13226 > > Over 1518-byte pkts(Jumbo): 0 > > Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0 > > Errors: 0, Discards: 0 > > Transmit Statistics: > > 1176133 packets, 1658862747 bytes > > Unicasts: 1174922, Multicasts: 952, Broadcasts: 259 > > Underruns: 0 > > Errors: 0, Discards: 0 > > Rate info (interval 299 seconds): > > Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate > > Output 0.000708 Mbits/sec, 0 packets/sec, 0.00% of line-rate > > Time since last interface status change: 01:19:15 > > > > La version (Pas de support donc pas de MAJ malheureusement...): > > > > bcn-sws-3-1# show ver > > > > Network Operating System Software > > Network Operating System Version: 4.1.1 > > Copyright (c) 1995-2014 Brocade Communications Systems, Inc. > > Firmware name: 4.1.1 > > Build Time: 19:48:22 Mar 19, 2014 > > Install Time: 12:34:44 Mar 23, 2015 > > Kernel: 2.6.34.6 > > > > BootProm: 2.2.0 > > Control Processor: e500v2 with 2048 MB of memory > > > > Appl Primary/Secondary Versions > > ------------------------------------------ > > NOS 4.1.1 > > 4.1.1 > > > > Une idée? > > Pas d'accès aux forums Brocade non plus sans support alors que la réponse > y est surement... > > > > Merci > > > > > > > > --------------------------- > > Liste de diffusion du FRnOG > > http://www.frnog.org/ > > > > --------------------------- Liste de diffusion du FRnOG http://www.frnog.org/
